usb pendrive strangness

From: Damon L. Chesser (dchesser4_at_cox.net)
Date: 01/01/04

  • Next message: Jan Minar: "Re: Bug Report-Deb Install says insert cd2 but doesn't eject cd1" 
    Date: Thu, 01 Jan 2004 11:48:58 -0600
To: Debian User <debian-user@lists.debian.org>

    On a stock debian sarge, fresh install, I can enter these two lines into
    fstab:

    /dev/sda /mnt/pendrive auto defualts,user,noauto,umask=002 0 0
    /dev/sdb1 /mnt/usbdrive auto defualts,user,noauto,umask=002 0 0

    I can then mount as user or root both devices. In Libranet 2.8.1, mosly
    sarge I can mount the usb drive IF it is sdb1, NOT sda1 or sdc1 or
    sdd1. I CANNOT mount /mnt/sda:

    user1@DAM-LN:~$ mount /mnt/pendrive
    mount: /dev/sda is not a valid block device
    user1@DAM-LN:~$
     
    Making it /dev/sda1 or c,b etc has no bearing. If I specifiy vfat
    (which is what I think it is) I get:

    kernel does not support fs hfs (or words to that effect).

    I think this is related to an upgrade and have seen this before. If I
    do a stock 2.8.1 install, I will have no problem. At some point seeking
    the coolest, best stuff, I will get an error in dmesg, which, if not
    directly relevent, tells me I will see this error with usb mas storage
    devices. I do not know what upgrade causes it. I have never tried to
    run this down before. Here is dmesg relevent output:

    usb.c: new USB bus registered, assigned bus number 1
    ehci_hcd 00:11.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4
    hub.c: USB hub found
    hub.c: 4 ports detected
    host/usb-uhci.c: $Revision: 1.275 $ time 12:28:35 Dec 6 2003
    host/usb-uhci.c: High bandwidth mode enabled
    host/usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11
    host/usb-uhci.c: Detected 2 ports
    usb.c: new USB bus registered, assigned bus number 2
    hub.c: USB hub found
    hub.c: 2 ports detected
    host/usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 11
    host/usb-uhci.c: Detected 2 ports
    usb.c: new USB bus registered, assigned bus number 3
    hub.c: USB hub found
    hub.c: 2 ports detected
    host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
    host/usb-ohci.c: USB OHCI at membase 0xe0e24000, IRQ 3
    host/usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] USB 1.0
    Controller (#2)
    usb.c: new USB bus registered, assigned bus number 4
    hub.c: USB hub found
    hub.c: 3 ports detected
    host/usb-ohci.c: USB OHCI at membase 0xe0e26000, IRQ 11
    host/usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] USB 1.0
    Controller
    usb.c: new USB bus registered, assigned bus number 5
    hub.c: USB hub found
    hub.c: 3 ports detected
    usb.c: registered new driver hid
    hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
    hid-core.c: USB HID support drivers
    ######later on in the file###########
    ide0(3,7):Using r5 hash to sort names
    usbdevfs: remount parameter error
    NTFS driver v1.1.22 [Flags: R/O MODULE]
    ########later on in the file, this shows the pluging in of the
    device###########
    hub.c: new USB device 00:02.3-2, assigned address 2
    usb.c: USB device 2 (vend/prod 0x90c/0x1000) is not claimed by any
    active driver.
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    scsi1 : SCSI emulation for USB Mass Storage devices
      Vendor: Model: USB CYBER DISK Rev:
      Type: Direct-Access ANSI SCSI revision: 02
    Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
    SCSI device sda: 32001 512-byte hdwr sectors (16 MB)
    usb_control/bulk_msg: timeout
    usb_control/bulk_msg: timeout
    usb_control/bulk_msg: timeout
    hub.c: USB device not accepting new address (error=-110)
    usb-storage: host_reset() requested but not implemented
    scsi: device set offline - command error recover failed: host 1 channel
    0 id 0 lun 0
    sda: test WP failed, assume Write Enabled
     sda: I/O error: dev 08:00, sector 0
     sda: I/O error: dev 08:00, sector 0
     I/O error: dev 08:00, sector 0
     unable to read partition table
    WARNING: USB Mass Storage data integrity not assured
    USB Mass Storage device found at 2
    USB Mass Storage support registered.
     unable to read partition table
    usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -110
    #####above line repeated about 20 times##########

    The message at boot (does not show up if I run dmesg) is:

    Starting Htoplug subsystem: Inputt*** cant synthesize input events
    -/proc/bus/input/devices missing
    pci*** cant synthesize PCI hotplug events
    usbsync: [oo1 oo1 oo1 oo2 oo1 ]

    /proc/bus has pci & usb, but no input. ???? Should it have input? IF
    so, how do I make input dir? I'm starting to think this is a kernel
    issue. I am using 2.4.23 on this box (stock Libranet kernel settings)
    and 2.4.21-1-I386 stock Sarge Debian kernel on the box these devices
    work on. Same family of motherboards (ECS k7s5a and k7s5a Pro) so
    hardware is not an issue. In addition, on the problem box (Libranet
    2.8.1) I have an USB-2 pci card, eliminating the possibility of an
    onboard usb problem. This has me scratching my head. Where do I look
    and what do I do? 

    -- 
Damon L. Chesser
dchesser@bigfoot.com
-- 
To UNSUBSCRIBE, email to debian-user-request@lists.debian.org 
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
  • Next message: Jan Minar: "Re: Bug Report-Deb Install says insert cd2 but doesn't eject cd1"

    Relevant Pages