Re: Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct
From: Joseph Jones (joe_at_bumpycarrot.cjb.net)
Date: 02/06/04
- Previous message: Information Technology: "Auto-response from the ACC Registration Helpline"
- Maybe in reply to: Joseph Jones: "Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Next in thread: Kent West: "Re: Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Reply: Kent West: "Re: Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 06 Feb 2004 15:07:50 +0000 To: debian-user@lists.debian.org
Adam Aube wrote:
> On Thursday 05 February 2004 12:06 pm, Joseph Jones wrote:
>
>>Adam Aube wrote:
>>
>>>Your interfaces file looks fine. Exactly what happens when you try to
>>>get your network interface working, and how do you try to do it?
>>
>> I try to get it working by starting up my PC. I was under the
>>impression that that was all was requied after installing the kernel
>>(it's all my Via Rhine based card needed).
>>
>>Upon bootup, it says something along the lines of eth1: ERROR while
>>getting interface flags: No such device (dmesg has ceased to work for
>>some reason, so I had to right it down as it flashed by) about 6 or so
>>times.
>
>
> Sounds like a driver problem to me. What does the output of lspci -vv
> show?
>
> Adam
>
>
Output follows (hope you don't mind me cc'ing to you and the list):
00:00.0 Host bridge: nVidia Corporation nForce CPU bridge (rev b2)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [40] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [60] #08 [2001]
00:00.1 RAM memory: nVidia Corporation nForce 220/420 Memory Controller
(rev b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:00.2 RAM memory: nVidia Corporation nForce 220/420 Memory Controller
(rev b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation: Unknown device 01aa (rev b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:01.0 ISA bridge: nVidia Corporation nForce ISA Bridge (rev c3)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [50] #08 [01e1]
00:01.1 SMBus: nVidia Corporation nForce PCI System Management (rev c1)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 5000 [size=16]
Region 1: I/O ports at 5500 [size=16]
Region 2: I/O ports at 5100 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation nForce USB Controller (rev
c3) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e6800000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: nVidia Corporation nForce USB Controller (rev
c3) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: nVidia Corporation nForce Ethernet
Controller (rev c2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e5800000 (32-bit, non-prefetchable) [size=1K]
Region 1: I/O ports at d800 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: nVidia Corporation: Unknown device
01b0 (rev c2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e5000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce Audio
(rev c2)
Subsystem: Asustek Computer, Inc.: Unknown device 8384
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e100 [size=256]
Region 1: I/O ports at e000 [size=128]
Region 2: Memory at e4800000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 PCI bridge: nVidia Corporation nForce PCI-to-PCI bridge (rev c2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: e4000000-e47fffff
Prefetchable memory behind bridge: f6f00000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:09.0 IDE interface: nVidia Corporation nForce IDE (rev c3) (prog-if
8a [Master SecP PriP])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at a800 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: nVidia Corporation nForce AGP to PCI Bridge (rev b2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Memory behind bridge: e3000000-e3ffffff
Prefetchable memory behind bridge: e7700000-f6efffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
01:06.0 Multimedia video controller: 3Dfx Interactive, Inc. Voodoo 2
(rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Region 0: Memory at f7000000 (32-bit, prefetchable) [size=16M]
01:07.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II]
(rev 43)
Subsystem: D-Link System Inc DFE-530TX rev A
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at e4000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti
4200] (rev a3) (prog-if 00 [VGA])
Subsystem: CardExpert Technology: Unknown device 0fc2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e3000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at e7800000 (32-bit, prefetchable) [size=512K]
Expansion ROM at e77e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
-- To UNSUBSCRIBE, email to debian-user-request@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
- Previous message: Information Technology: "Auto-response from the ACC Registration Helpline"
- Maybe in reply to: Joseph Jones: "Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Next in thread: Kent West: "Re: Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Reply: Kent West: "Re: Need help, dual NICs, don't know whether this /etc/network/interfaces file is correct"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
