mount unable to determine ipod filesystem type, kernel 2.6.5

From: Alex C-G (alexcg_at_gmail.com)
Date: 05/15/04

  • Next message: Phillipus Gunawan: "TPG DSL200 on Debian" 
    Date: Sat, 15 May 2004 17:17:16 +1200
To: debian-user@lists.debian.org

    Hi, I just upgraded to kernel 2.6.5-1 and now when i try to mount my
    ipod I get the following:

    mount: I could not determine the filesystem type, and none was specified

    It worked fine with kernel 2.4.22. What can I do to make it work with 2.6?

    Got the following from dmesg:

    usb 3-2: new full speed USB device using address 2
    usb 3-2: device not accepting address 2, error -71
    usb 3-2: new full speed USB device using address 3
    usb 3-2: device not accepting address 3, error -71
    usb 1-4: new high speed USB device using address 2
    Initializing USB Mass Storage driver...
    scsi0 : SCSI emulation for USB Mass Storage devices
      Vendor: Apple Model: iPod Rev: 1.50
      Type: Direct-Access ANSI SCSI revision: 02
    sda: Spinning up disk.....ready
    SCSI device sda: 29297520 512-byte hdwr sectors (15000 MB)
    sda: assuming Write Enabled
    sda: assuming drive cache: write through
     /dev/scsi/host0/bus0/target0/lun0: p1 p2
    Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    USB Mass Storage device found at 2
    drivers/usb/core/usb.c: registered new driver usb-storage
    USB Mass Storage support registered.
    FAT: Unrecognized mount option "0" or missing value
    EFS: 1.0a - http://aeschi.ch.eu.org/efs/
    FAT: Unrecognized mount option "0" or missing value
    FAT: invalid media value (0x2f)
    VFS: Can't find a valid FAT filesystem on dev sda1.
    FAT: invalid media value (0x2f)
    VFS: Can't find a valid FAT filesystem on dev sda1.
    FAT: Unrecognized mount option "0" or missing value
    FAT: Unrecognized mount option "0" or missing value
    ieee1394: Initialized config rom entry `ip1394'
    sbp2: $Rev: 1170 $ Ben Collins <bcollins@debian.org>
    FAT: Unrecognized mount option "0" or missing value

    Anyone have any ideas?

    Thanks,
    Alex C-G 

    -- 
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org 
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
  • Next message: Phillipus Gunawan: "TPG DSL200 on Debian"

    Relevant Pages

    • [opensuse] USB stick mount failure
      ... I am trying to read a USB. ... SCSI device sda: 4089855 512-byte hdwr sectors ... reset high speed USB device using ehci_hcd and address 2 ... FAT: ...
      (SuSE)
    • Re: crash
      ... connected to my Ubuntu notebook through the USB port. ... But mounting it or running fsck on it as ext3 doesn't ... behind a FAT translation service. ... filesystem, ...
      (alt.os.linux)
    • Re: USB 2.0 ports not working
      ... loaded the fat filesystem driver, so i seems that the device is ... Did you used the same USB disk in both tests? ... recognize fronts on the pin where the host controller is connected). ... In this case the host controller will keep it's interrupt line low ...
      (microsoft.public.windowsce.platbuilder)
    • Re: This is what we did here 12 years ago
      ... The cheap floppies are not worth buying. ... I wish this MoBo booted from USB. ... think of to give it a FAT and file structure, ...
      (misc.survivalism)
    • WinCE operates FAT file system in strange manner
      ... I am developping a usb mass storage function driver in WinCE4.2. ... READ10 or WRITE10 CBW posted from usb host. ... directory(FAT32 partition),then I find the actual FAT table is not ... write,but WInCE set a sector of data section to FAT Table.And the new ...
      (microsoft.public.windowsce.platbuilder)