Re: Printer setup howto
- From: Csanyi Pal <csanyipal@xxxxxxxxxxxxxx>
- Date: Sun, 30 Apr 2006 18:03:41 +0200
On Sun, Apr 30, 2006 at 11:23:09AM -0400, Roberto C. Sanchez wrote:
I'm not sure what you are asking. Are you printing on Letter or A4 in
How can I setup margins correlated to the edges of A4 paper?
I have the printer HP Business Inkjet 1000 and use the hpjis driver to
print.
If I use Gnome-cups-manager to setup the printer, and I print a test
page therein with format paper of A4, then to check margin settings, I
can use a ruler to verify that margin lines are printed at 0.5, 1, and
1.5 cm from the edge of the paper on all sides.
I verified these margin lines and get the results
from the top edge:
instead of 0.5 cm - 0.6 cm
instead of 1 cm - 1.1 cm
instead of 1.5 cm - 1.6 cm
from the right edge:
instead of 0.5 cm - 0.8 cm
instead of 1 cm - 1.3 cm
instead of 1.5 cm - 1.8 cm
from the bottom edge:
0.5 cm - don't show up !!!
1 cm - don't show up !!!
1.5 cm - 1.5 cm
from the left edge:
0.5 cm - 0.3 cm
1 cm - 0.8 cm
1.5 cm - 1.3 cm
How can I setup these margin lines to the right dimension?
Why don't show up the margin lines from the bottom edge of the paper at
0.5 cm and 1 cm?
If I do Align Cartridges... within HP Linux Imaging and Printing System
window, then the printer print 2 pages and on the first page print at
bottom corners 2 point:
from the left edge 0.6 cm
from the right edge 0.6 cm
from the bottom edge 0.5 cm
Accordingly to this abowe the printer can print from all edge of paper
A4 at 0.5 cm, but when I try to print say a draw.dxf from QCAD
application, then the printer don't print at the bottom edge of A4
paper. Why don't print there?
I appreciate any advices!
the firstplace?
(Sorry for my English, I'm Hungarian.)
I'm printing on A4 in the first place.
|-----------0.5 cm-------------|
||----------1.0 cm------------||
|||---------1.5 cm-----------|||
||| |||
||| |||
||| |||
... ...
||| |||
||| |||
||| |||
|||---------1.5 cm-----------|||
The margin line at 1.0 cm is not showed up.
The margin line at 0.5 cm is not showed up.
If I set up the printer right then I expect the following picture with
printed margin lines:
|-----------0.5 cm-------------|
||----------1.0 cm------------||
|||---------1.5 cm-----------|||
||| |||
||| |||
||| |||
... ...
||| |||
||| |||
||| |||
|||---------1.5 cm-----------|||
||----------1.0 cm------------||
|-----------0.5 cm-------------|
How can I set up the printer to get printed documents like this?
Any advices is appreciated!
--
Regards, Csányi Paul
http://www.ektf.hu/~Csanyi.Pal (Up to now, it is in Hungarian only.)
http://csanyipal.info/moodle <<<--- Moodle - Course Management System
http://csanyipal.info:81 <<<--- sTeam - Cooperative Learning
--
To UNSUBSCRIBE, email to debian-user-REQUEST@xxxxxxxxxxxxxxxx
with a subject of "unsubscribe". Trouble? Contact listmaster@xxxxxxxxxxxxxxxx
- References:
- Printer setup howto
- From: Csanyi Pal
- Re: Printer setup howto
- From: Roberto C. Sanchez
- Printer setup howto
- Prev by Date: boot disk for grub; network config; printer pb
- Next by Date: Re: [debian] Re: OT: Politics [Was:Social Contract]
- Previous by thread: Re: Printer setup howto
- Next by thread: boot disk for grub; network config; printer pb
- Index(es):
Relevant Pages
|