Re: Install which Linux? (or avoiding dirty birds)
- From: Wayne Topa <linuxone@xxxxxxxxxxxxx>
- Date: Sun, 10 Jun 2007 09:39:53 -0400
Gayle Lee Fairless(fairless@xxxxxxxx) is reported to have said:
Although I would have replied sooner; there was a death in the family.
Sorry for your loss.
<--<snip>-->
Gayle Lee Fairless(fairless@xxxxxxxx) is reported to have said:
Wayne Topa <linuxone@xxxxxxxxxxxxx> replied:
Then I hope the US Robotics card will work, or I get lucky with the
Belkin adapter!
You may be in luck after all.
A google for "US Robotics USR5410 Linux" came up with a review that
wasn't too good, but the second one you might like. The headline is
"US Robotics goes Linux" and your 5410 in included in the writeup.
<http://www.ameinfo.com/32533.html>
I found it and the reference to Linuxant and their product, DriverLoader:
(quote off www.Linuxant.com)
DriverLoader is a revolutionary compatibility-wrapper allowing standard
Windows NDIS (Network Driver Interface Specification) drivers shipped by
hardware vendors to be used as-is on Linux x86 systems ....
(end of quote)
It appears that the program supports both the Belkin USB wireless device
and
the US Robotics USR5410 PCMIA card. I have to hook it up and find out
under
both Linux and Windows XP Pro.
I try to stay away from the NDIS wrappers but if you have a card
and thats the only way....
<--<snip>-->
I learned enough vi to naviage through a text file and make simple
changes.
Although I have mutt on my Debian sarge box, I do not understand it as well
as I do vi. The messages to root go through mutt. I also have seen and
used
a version of emacs on the Amiga.
Mutt is a command line Mail User Agent (MUA) and it uses vim, an
expandad vi, to write/reply to mail. IMHO these are 2 of the most
useful apps.
Try "aptitude show mutt" | "apt-cache show mutt" & "aptitude|apt-cache
show vi".
IIRC the netinstall uses the nano editor because of its small size.
<--<snip>-->
I was able to install a baic Debian GNU/Linux etch system on the
Thinkpad with the official network installation CDROM. Since I was
not connected to the Internet, I need to know how to get network setup
working and start installing packages.
'If' the drivers were installed correctly: iwconfig Should show something
installed.
------------------------------------------------
{TP 770, running a USB wireless adapter }
$ iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
wlan0 IEEE 802.11-b ESSID:"Mtntop_AP" Nickname:"Mtntop_AP"
Mode:Managed Frequency:2.437 GHz Access Point: 00:0F:B5:11:37:1F
Bit Rate:11 Mb/s Tx-Power:18 dBm
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=25/92 Signal level=-66 dBm Noise level=-91 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
------------------------------------------------
If a device shows up then the driver is loaded. Then you have to configure
your /etc/network/interfaces file. See man interfaces.
------------------------------------------------
{ the above 770's interfaces file}
$cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo
down route del -net 127.0.0.0 netmask 255.0.0.0 dev lo
# The primary network interface
# Ashton USB Dongle
# NOTE: all setup for this USB Dongle is is in /etc/wlan/
# and the startup script in /etc/network/if-pre-up.d/linux-wlan-ng-pre-up
# and down with the /etc/network/if-post-down.d/linux-wlan-ng-post-down
auto wlan0
iface wlan0 inet dhcp
------------------------------------------------
Once you have the above interfaces file done then to connect to your
AP do first.
/etc/init.d/networking force-reload
then
$ ifup (interface name from iwconfig)
I looked
at Martin Kraft's Debian maintainer notes on fluxbox. Did you have to
install a patch
to get yours working?
I did not install any flux patches. Note I am running lenny/Testing not
etch/stable.
I'll leave it there until we know if the wrappers got the drivers installed
correctly.
I'll mention some other stuff for you to ponder.
There, usually, is no need to reboot the system. When working on
networking you can restart networking, after making changes to the
interfaces file by doing as root /etc/init.d/networking restart.
$ ifconfig (show what interfaces are up)
The dhcp, in the interfaces file, is the command to get access to your
AP. I have to assume that the netinstall includes the dhcp client.
Wayne
--
Press any key to continue or any other key to quit...
_______________________________________________________
--
To UNSUBSCRIBE, email to debian-user-REQUEST@xxxxxxxxxxxxxxxx
with a subject of "unsubscribe". Trouble? Contact listmaster@xxxxxxxxxxxxxxxx
- References:
- Re: Install which Linux? (or avoiding dirty birds)
- From: Gayle Lee Fairless
- Re: Install which Linux? (or avoiding dirty birds)
- Prev by Date: what wants to remove gcc?
- Next by Date: Re: what wants to remove gcc?
- Previous by thread: Re: Install which Linux? (or avoiding dirty birds)
- Next by thread: Re: Install which Linux? (or avoiding dirty birds)
- Index(es):
Relevant Pages
|
