Re: 3C905-TX problems

From: Jim Cornette (jim-cornette_at_insight.rr.com)
Date: 01/31/04

  • Next message: John Stroud: "RE: 3C905-TX problems"
    To: fedora-list@redhat.com
    Date: Sat, 31 Jan 2004 16:48:02 -0500
    
    

    Michael Bernstein wrote:
    > Hi,
    >
    > I'm having problems with my first Linux installation (so expect some
    > naivite). The Ethernet card - a 3C905-TX on an MSI K7N2G mobo - is a
    > real mare!! Let me say that all works well under WinXP. The NIC is
    > connected to the Cable modem (ftom ntl in the UK).
    >
    > I had loads of trouble getting the board to go "active" at all, but
    > finally managed after I turned off kudzu ("chkconfig kudzu off" and a
    > reboot). Now I can ping and browse, but everything goes at a snail's
    > pace. If I ping the BBC website I get 50% packet loss.
    >
    > I've spent a LOT of time with this now so help would be greatly
    > appreciated.
    >
    >
    > Many thx,
    > Mike
    >
    > PS I tried to work with the on-board nVIDIA ethernet but that wasn't
    > recognised, and nVIDIA don't supply a driver for core 2.4.22-1.2115
    >

    This card stopped working correctly with The beta for RH10, which turned
    into Fedora Core 1.

    The card has worked from at least RHL 5.2 up to RHL9. It doesn't work
    well with Fedora Core 1. Fedora Core 2 (Test 1) comes out later next
    week (mid-week). I hope the card works better with the 2.6 kernel driver
    for the card and the tools which setup, detect the card. (ethertool,
    kudzu, hwdata,system-config-network and the like.)

    Mine was a PCI card version (Rev A) and went back to it's original owner.

    The workarounds I have heard so far are to set the mode in the
    modules.conf file (or modprobe.conf file for the 2.6 kernel)

    Disable Kudzu and the graphical bootloader.

    If possible, i would get a cheap NIC, to get a reliable connection,
    until the problem with the 3Com NIC get fixed. (If ever)

    Jim

    -- 
    fedora-list mailing list
    fedora-list@redhat.com
    To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
    

  • Next message: John Stroud: "RE: 3C905-TX problems"

    Relevant Pages

    • RE: TVtime
      ... For users of Fedora Core releases ... What is really freaky is if I run lsmod there is no driver loaded. ... if I modprobe the module the Card starts to work but as I said I only ... Chadley - Linux Rocks ...
      (Fedora)
    • Re: cheap low-profile pci ethernet adapters
      ... Dimension 300 Mhz system and it didn't have a network card in it. ... I was able to do an NFS install of Fedora Core 3 just fine. ... My friend is happily ...
      (Fedora)
    • still scsi problems - Adaptec - scsi0: Someone reset channel A
      ... Fedora Core R2. ... Jun 28 12:03:49 salvatore kernel: scsi0: Dumping Card State while idle, ... Götz Reinicke ...
      (Fedora)
    • FC3 install on Adaptec 2410SA - Adaptec says NO
      ... Adaptec 2410SA SATA RAID cards working with Fedora Core 3. ... installs on these systems, and I was successful in running FC3 on a ... the FC3 causes the on-card ... The OS that you are using is not supported by this controller card. ...
      (Fedora)
    • HOWTO: FC2 USB Multicard Reader
      ... you must recompile the scsi module with "Probe all LUNs". ... I had to reload the usb_storage module every time i added or removed a card ... linux fedora core 2 fc2 usb multi card multicard reader ...
      (Fedora)