Re: Applying Kernel Patch-Errors on FC1

From: Murali P (linuxmurali_48_at_yahoo.co.in)
Date: 04/29/04

  • Next message: d l: "Re: Netsend equivalent"
    Date: Thu, 29 Apr 2004 16:56:25 +0100 (BST)
    To: "ne..." <akabi@speakeasy.net>, For users of Fedora Core releases <fedora-list@redhat.com>
    
    

     --- "ne..." <akabi@speakeasy.net> wrote: > On Apr 28,
    2004 at 12:37, Murali P in a soothing
    > rage wrote:
    >
    > >Hello List
    > >I had earlier reported some compilation errors on
    > >2.6.3 kernel.This was after applying the patch :
    > >"packet-2.6.3.patch " to enable packet writing for
    > >CD-RW.
    > What kernel source are you using and where is it
    > resident?
    >
    > >Since then I managed to rectify thoseerrors.I
    > >recompiled and followed the detailed tips posted in
    > >this list.All steps got through correctly but "make
    > >install" failed with the message :
    > >1)Could not load
    >
    >/lib/modules/2.6.3-2.1.204/unsupported/fs/hfs/hfs.ko
    >
    > >2)Could not load
    > >/lib/modules/2.6.3-2.1.204custom/modules.dep :No
    > such
    > >file or directory ' mkinitrd failed' .Next I copied
    > >the 'bzImage' generated successfully to /boot and
    > >renamed it as vmlinuz-2.6.3-udf to indicate that
    > the
    > >image is packet-writing enabled for CD-RW.
    > When you do this, the kernel name should match what
    > is in the Makefile and also the modules in
    > /lib/modules.
    > They cannot have different names. From what I see
    > above
    > it seems you have three different versions.
    >
    > >However, on booting the new kernel image I found
    > that
    > >all the modules are missing.The old image is also
    > >giving the same errors.
    > You never said the modules were installed properly.
    > If they were not, then the modules.dep may occur.
    >
    > >I know that I have messed up my FC1 system. I think
    > >that it has something to do with
    > 2.6.3-2.1.204custom
    > >directory which is being searched but is
    > >non-existent.Hence I removed the word custom from
    > >EXTRAVERSION=2.6.3-2.1.204custom line in the top
    > >level Makefile.
    > >This does not get my system back to the old state.
    > > I request for urgent help in restoration of my
    > >system.Could some one respond please?
    > You should have the kernel the system came with...
    >
    > Say you install the kernel-source rpm, this will
    > install
    > to /usr/src/linux-<version>. Now you apply the patch
    > to
    > this and it succeeds. Step 1 safely accomplished. So
    > now
    > you cd /usr/src/linux-<version> and edit the
    > Makefile.
    > Since you like your EXTRAVERSION as udf, you add
    > this
    > as 'EXTRAVERSION = -udf'. Next you do a 'make
    > mrproper'.
    > Now the source is in a nice clean state. Then
    > - Copy a 2.6.x config if you have one to
    > /usr/src/linux-<version>/.config and do 'make
    > oldconfig'
    > - I then do a'make menuconfig' and recheck _all_ my
    > options.
    > - 'make clean all'
    > - 'make modules_install install'
    > - Check grub.conf and reboot.
    >
    > If you have problems with these steps, it may happen
    > because of the options you chose in the 'make
    > menuconfig'
    > step. Redo from that point on.
    >
    > HTH.
    > N.Emile...
    Thanks a lot.Your prescription worked.Packet writing
    is enabled on my CDRW device when I rebooted with the
    new bzImage copied as vmlinuz-2.6.3-udf under /boot.
    But strangely (or is it not?) 'make install' failed
    with the messages : "mkinitrd failed" and "could not
    load /lib/modules/2.6.3-2.1.204custom/modules.dep:No
    such file or directory ".
    Although system is fine,but what is the meaning of
    such error messages?
    Once again I thank you very much.
    Murali

    ________________________________________________________________________
    Yahoo! India Matrimony: Find your partner online. http://yahoo.shaadi.com/india-matrimony/

    -- 
    fedora-list mailing list
    fedora-list@redhat.com
    To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
    

  • Next message: d l: "Re: Netsend equivalent"

    Relevant Pages

    • Re: Make Error (please help i need my webcam to work)...
      ... there should be a file called Makefile. ... > Looks like you have to create a soft link into the kernel source. ... > i'm having a real tough time trying to install this nw802 video driver ... > for my dark ring logitech quickcam. ...
      (comp.os.linux.misc)
    • Re: Make Error (please help i need my webcam to work)...
      ... Did you look at line 485 in the Makefile? ... There should be a README and INSTALL file in the driver source ... I'm confused as to why you needed to use a 2.4 driver for a 2.6 ... >> Looks like you have to create a soft link into the kernel source. ...
      (comp.os.linux.misc)
    • Re: [SLE] Newbie questions about kernel update and Konstruct, and Mozilla as default browser
      ... > occurs when I try to go to the kernel configuration in the control center. ... That page tells you what kernel you have installed, not what kernel source you ... > I ran into the same problem as others have, that when trying to install one ... upgrade the SuSE installed stuff. ...
      (SuSE)
    • Kernel Source
      ... I recently bought a GForce 6600GT AGP graphics card to ... they wouldn't install, something about no pre-comiled kernel headers ... and no source for my 2.4.x kernel. ... or can I not download the 2.6.x kernel source ...
      (Debian-User)
    • input method on fc3?
      ... FC3 and soundcard ... >> without problems and sound works fine. ... What modules were loaded with kernel ... I can install and configure samba on Linux as easily as I can install ...
      (Fedora)