Re: 3Com 3c2000 NIC support? - FC3?
From: Karen Spearel (kas11_at_tampabay.rr.com)
Date: 04/30/04
- Previous message: John Nichel: "Re: Killing a process that won't die"
- In reply to: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Next in thread: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Reply: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 30 Apr 2004 13:16:19 -0400 To: For users of Fedora Core releases <fedora-list@redhat.com>
Dave wrote:
>>>On my Asus K8V motherboard is a 3-Com 3c2000 NIC. I have downloaded and
>
> compiled the Driver (as far as I can tell, new to this distro) but I am
> having problems getting it to load with the kernel and trying to configure
> it. The log file messages had some text relating to the startup of the
> driver but I cannot access the internet etc.
>
>>>I followed the instructions to extract the tar, "make load" then
>
> "ifconfig eth0 up", but when I go to the network configuration utilities in
> FC1 I can't find the card or driver. Nor can I figure out how to load it on
> boot. The instructions talk about using "/etc/modules.conf file" or insmod
> . Also as I cannot select the NIC I cannot tell if it is set to use DHCP.
>
>>>>From the readme file
>>>+++++SNIP+++++++++
>>
>>---SNIP ----
>>
>>>+++++++SNIP+++++++
>>>
>>>I use an old computer with Smoothwall on it which provides the DHCP.
>>>
>>>Thanks
>>> Dav
>>>
>
> ----- Original Message -----
> From: "eng.Ilia Dulgerov" <ilia@linuxman.biz>>
>
>>I had same problem with ASSUS mobo and i found that modprobe sk98lin do
>>the trick and driver loaded and detected card properly.
>>nex is ifconfig I assume it is common way to config.
>>Hope this help
>>--
>>///eng.Ilia Dulgerov, <office@linuxman.biz>
>>// ph.+359 888 541553
>
>
> Thanks, Question: what is modprobe &/or sk98lin? As far as I can find with
> google sk98lin is for a different NIC and I'm not sure what to do with
> modprobe.
>
> You'll see another thread that I just posted to about 10 min ago "Re: 3com
> 3c2000 NIC support" where I am trying re-compile the 3c2000 drivers and get
> them into the /lib/.../net/ directory.
>
> Dave
>
>
>
Your K8V has a 3c940 chip on the motherboard. IIRC, much of the 3c2000
driver was taken from the sk98lin driver originally written by
Syskonnect to support their wide range of network interface cards, at
least one of which uses the 3c940.
There were issues with the sk98lin at various points during the run up
to FC1 release and there have been points since were it got broken...but
these have always be quickly fixed...the RH/Fedora people in charge of
these issues are exceptionally responsive.
Anyhow, the Sk98lin driver was functioning fine with an updated FC1
system although getting to this point from the FC1 release CDs might
require installation with a $10 Realtek card or something in order to
acquire the updates...once FC1 is fully updated, the 3c940 on your K8V
will work with the sk98lin driver. The sk98lin driver supports a wide
variety of hardware but is the Fedora supported driver for the 3c940.
If you decide to switch to FC2 Test 3, the installer will find your
hardware and install the sk98Lin driver automagically. Test 3 is
working very well with my K8V.
HTH,
KAS
-- fedora-list mailing list fedora-list@redhat.com To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
- Previous message: John Nichel: "Re: Killing a process that won't die"
- In reply to: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Next in thread: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Reply: Dave: "Re: 3Com 3c2000 NIC support? - FC3?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
