Re: Grub Problem (?) Installing FC4 dual boot with Win2K

From: Jim Cornette (fc-cornette_at_insight.rr.com)
Date: 08/09/05

  • Next message: Reuben D. Budiardja: "Re: wlan not present"
    Date: Mon, 08 Aug 2005 18:31:35 -0400
    To: For users of Fedora Core releases <fedora-list@redhat.com>
    
    

    Mike McCarty wrote:

    > Bill Bernauer wrote:
    >
    >> Jeff Vian wrote:
    >>
    >>> 1) Check the drives jumper settings and if these drives are on a
    >>> cable-select cable I suggest they both be jumpered for cable-select.
    >>
    >>
    >> Both drives are set for CS.
    >
    >
    > [snip]
    >
    > Opinion mode ON
    >
    > CS is EVIL. Do not use CS. I have never seen a machine use CS
    > run any better than one with separate Master/Slave settings.
    > I have seen machines with CS set get confused about which
    > drive is which.
    >
    > Opinion mode OFF
    >
    > YMMV
    >
    > Mike

    Flip-flop mode:
    Setting the jumpers to master / slave on even a cable where pin 28 is
    used for signaling the Master / slave should always work. The fact that
    you have a cable setup for CS should not matter. Setting the jumpers
    seems to be best practice for predictability.
    *However* defective hardware which wants to be master, even when
    jumpered as slave, but function correctly is set to CS (cable select)
    are legitimate reasons for choosing CS over jumper settings.
    Either way would work *sometimes* - :-)

    Jim

    An interesting link described below shows some good information.
    http://www.unixwiz.net/techtips/ide-cable-select.html

    -- 
    The kernel is not there to cover up for usermode programmers inability
    to get things right. It has enough to do covering up for the hardware folk
    	- Alan Cox on linux-kernel
    -- 
    fedora-list mailing list
    fedora-list@redhat.com
    To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
    

  • Next message: Reuben D. Budiardja: "Re: wlan not present"

    Relevant Pages

    • Re: Questions about sis7012+snd_intel8x0 sound card problem
      ... > config my sound card, ... surround volume control and the master volume control ... amixer set Master 50 should also set master ... One caveat -- I'm not sure if the settings are ...
      (Debian-User)
    • Re: Does Adding a 2nd IDE Hard Drive (Master/Slave setup) Slow Down Both Drives?
      ... on Cable Select and not jumpers to set the Master/Slave ... The IDE channel controler has no way to know which drive ... the drives indicate whether they are One or the Other. ... That HD boot order has the "Master" on IDE channel 0 at ...
      (alt.sys.pc-clone.dell)
    • Re: UDMA & mode 4
      ... Master will be on the end, ... PCs that have trouble with hard drives bigger than that. ... > connector ideally is meant for the master mode & which one ... > In some HDDs there are 5 jumper settings while in some ...
      (microsoft.public.windowsxp.hardware)
    • Re: UDMA & mode 4
      ... Master will be on the end, ... PCs that have trouble with hard drives bigger than that. ... > connector ideally is meant for the master mode & which one ... > In some HDDs there are 5 jumper settings while in some ...
      (microsoft.public.windowsxp.newusers)
    • [SLE] RESOLVED Re: [SLE] CD burning problems with 9.1 AGAIN!
      ... The new settings: dvdrom on secondary as master, dvdrw on secondary as slave. ...
      (SuSE)