Kernel errors?
From: Tom Diehl (tdiehl_at_rogueind.com)
Date: 09/29/05
- Previous message: fredex: "Re: OT: Massachusetts Verdict: MS Office Formats Out"
- Next in thread: Peter Arremann: "Re: Kernel errors?"
- Reply: Peter Arremann: "Re: Kernel errors?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Wed, 28 Sep 2005 21:11:58 -0400 (EDT) To: fedora-list@redhat.com
HI all,
I have an FC4 machine that been running fine for several months using only eth0
and eth1. Today I tried to bring up eth2 for the first time and I got the
messages below. Can someone tell what is going on here and more importantly how
to fix it?
This is an FC4 machine running 2.6.12-1.1456_FC4 kernel.
Sep 28 20:50:24 taz kernel: irq 10: nobody cared!
Sep 28 20:50:24 taz kernel: [<c0151e74>] __report_bad_irq+0x24/0x7f
Sep 28 20:50:24 taz kernel: [<c0151f46>] note_interrupt+0x59/0x83
Sep 28 20:50:24 taz kernel: [<c0151220>] __do_IRQ+0x1f7/0x347
Sep 28 20:50:24 taz kernel: [<c0105b2d>] do_IRQ+0x4a/0x82
Sep 28 20:50:24 taz kernel: =======================
Sep 28 20:50:24 taz kernel: [<c0103c1e>] common_interrupt+0x1a/0x20
Sep 28 20:50:24 taz kernel: [<c01286ec>] __do_softirq+0x2c/0x8a
Sep 28 20:50:24 taz kernel: [<c0105c39>] do_softirq+0x3e/0x42
Sep 28 20:50:24 taz kernel: =======================
Sep 28 20:50:24 taz kernel: [<c0105b34>] do_IRQ+0x51/0x82
Sep 28 20:50:24 taz kernel: [<c0103c1e>] common_interrupt+0x1a/0x20
Sep 28 20:50:24 taz kernel: [<c024c6fe>] acpi_processor_idle+0x10e/0x272
Sep 28 20:50:24 taz kernel: [<c01010a6>] cpu_idle+0x34/0x4c
Sep 28 20:50:24 taz kernel: [<c04256ea>] start_kernel+0x164/0x1be
Sep 28 20:50:24 taz kernel: [<c04252e5>] unknown_bootoption+0x0/0x1b6
Sep 28 20:50:24 taz kernel: handlers:
Sep 28 20:50:24 taz kernel: [<c02d3dde>] (usb_hcd_irq+0x0/0x52)
Sep 28 20:50:24 taz kernel: [<de8868f8>] (rhine_interrupt+0x0/0x25c [via_rhine])
Sep 28 20:50:24 taz kernel: Disabling IRQ #10
Sep 28 20:50:28 taz kernel: printk: 1 messages suppressed.
Sep 28 20:50:28 taz kernel: martian source 67.62.182.165 from 67.62.182.1, on dev eth2
Sep 28 20:50:28 taz kernel: ll header: ff:ff:ff:ff:ff:ff:00:09:43:10:be:80:08:06
Sep 28 20:50:30 taz kernel: NETDEV WATCHDOG: eth1: transmit timed out
Sep 28 20:50:30 taz kernel: eth1: Transmit timed out, status 1003, PHY status 786d, resetting...
Sep 28 20:50:30 taz kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
Sep 28 20:50:34 taz kernel: martian source 67.62.181.186 from 67.62.181.1, on dev eth2
Sep 28 20:50:34 taz kernel: ll header: ff:ff:ff:ff:ff:ff:00:09:43:10:be:80:08:06
Sep 28 20:50:37 taz kernel: loop: loaded (max 8 devices)
Sep 28 20:50:37 taz kernel: martian source 67.62.181.186 from 67.62.181.1, on dev eth2
Sep 28 20:50:37 taz kernel: ll header: ff:ff:ff:ff:ff:ff:00:09:43:10:be:80:08:06
Sep 28 20:50:41 taz kernel: irq 10: nobody cared!
I am not sure what information to include but lspci -vv shows the following:
(taz pts1) # lspci -vv
00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-dbffffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 8b)
Subsystem: VIA Technologies, Inc.: Unknown device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at df003000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 15
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at dc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin D routed to IRQ 11
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at e000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at df001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Ethernet controller: Linksys NC100 Network Everywhere Fast Ethernet 10/100 (rev 11)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at df002000 (32-bit, non-prefetchable) [size=1K]
00:14.0 Ethernet controller: Linksys NC100 Network Everywhere Fast Ethernet 10/100 (rev 11)
Subsystem: Linksys: Unknown device 0574
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (16000ns min, 32000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at df004000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
(taz pts1) #
Is this indicative of some kind of hardware conflict or a bug? I do not understand
what is going on here, so any help would be appreciated.
Regards,
Tom Diehl tdiehl@rogueind.com Spamtrap address mtd123@rogueind.com
-- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
- Previous message: fredex: "Re: OT: Massachusetts Verdict: MS Office Formats Out"
- Next in thread: Peter Arremann: "Re: Kernel errors?"
- Reply: Peter Arremann: "Re: Kernel errors?"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
