Re: Bluetooth wireless Question

Micheal,

I hope your bluetooth dongle hardware is compatible with Linux, there
are good chances. So plug it in to the usb port of your notebook. Once
you plugged in the dongle, please run the command /usr/sbin/hciconfig
to ensure your bluetooth dongle in now accepted and active with the
hotplug system. Out put will be something like as below, notice you
will see the proper mac address.

hci0: Type: USB
BD Address: 00:39:36:04:65:34 ACL MTU: 678:8 SCO MTU: 48:10
UP RUNNING PSCAN ISCAN
RX bytes:107 acl:0 sco:0 events:14 errors:0
TX bytes:303 acl:0 sco:0 commands:14 errors:0

Basically two of the service scripts are involved and their related
setup, the service scripts in question are: /etc/rc.d/init.d/bluetooth
and(if_required_read_below) /etc/rc.d/init.d/dund

If you have pairing problems of Bluetooth-PC with other Bluetooth
devices in range, you might want to suspect DBUS system un-ability and
then need to make changes in file /etc/bluetooth/hcid.conf :
replace_line : dbus_pin_helper;
replace_with : pin_helper /usr/bin/bluepin;
then execute command /sbin/service bluetooth restart
next try pairing again.

Thats enough as short and sweet for (1) below, else keep reading if
you have other requirements.
--
Here the scripts in question also depends on what you want to do with
the bluetooth dongle device attached on to the PC:

1) You require basic Obex (File Transfer) functionality,
- So if your dongle is now detected as in output of hciconfig, the
service script concerned in /etc/rc.d/init.d/bluetooth and you'll also
need to execute gnome-obex-server from the run-prompt or terminal,
while you are logged on to a X (GUI) session.
- To send files from a bluetooth device choose to send file to PC as
detected in range by the device e.g your PDA or mobile phone.
- If you need send files from the PC to a bluetooth device run
gnome-obex-send /path/to/file

2) You have a GPRS or CDMA phone you want to use as a modem to your PC,
- You will need to run command /usr/bin/hcitool scan and identify your
modem device form the output as for e.g: 00:0J:EJ:9A:A2:AB T630
, so note the MAC addess of the modem device
- Edit the file /etc/bluetooth/rfcomm.conf , in the file look for
block rfcomm0 , and change the sample MAC address with the mac address
of your Bluetooth modem device then run command /sbin/service
bluetooth restart
- Ensure your Bluetooth modem has its bluetooth status as on, then run
command /usr/bin/rfcomm -a ensure it has been binded to the PC this
should be binded to rfcomm0 and a device node rfcomm0 will also be
found in /dev directory as /dev/rfcomm0 , you might like to test if
this modem is found by wvdial,
- To test with wvdial, I suggest create a temporary softlink to
/dec/rfcomm0 as /dev/modem and run command /usr/bin/wvdialconf
/tmp/wvdial.conf

I hope this is quiet much for now, please let me know if perhaps you
need a dial-in for your PDA or other bluetooth PC.

Cheers,

on your system you will like to ensure those start up in your desired
system runlevels, I assume 3 & 5 as:
/sbin/chkconfig --level 35 bluetooth on
/sbin/chkconfig --level 35 dund on




On 1/14/06, Michael Wright <michael_wright@xxxxxxxxxxx> wrote:
> Hi Floks
>
> I want to setup wireless using bluetooth I've look on there website but
> there seams to be not many answers for fedoracore, how do i go about
> seting it up using it for my laptop.
>
> Regards
> Michael
>
> --
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
>

--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list

Relevant Pages

  • [a bit OT] bluetooth with MAC OS
    ... bluetooth LAN. ... bluetooth LAN access server, rfcomm_pppd runs and listen to channel 7, ... Now the problem comes with MAC OS. ... username/password I am rejected with "modem doesn't response". ...
    (freebsd-net)
  • Re: flushing a widicom bluetooth serial port
    ... Instead of trying to access the bluetooth dongle through the serial ... have you thought of using a Socket connection? ... toolbar to access the port. ...
    (microsoft.public.dotnet.languages.csharp)
  • Re: bluetooth dongle to dongle
    ... Im looking at bluetooth to cominucate with a remote mcu from my pc, ... many medium mcus have usb port wich act as slave devices but a few have ... Theres 3 chips inside the bluetooth dongle with up to 40pins, ...
    (sci.electronics.design)
  • Bluetooth SDP issue on CE 5.0
    ... I am trying to include usb bluetooth dongle support on my terminal and ... I am trying to use OBEX file transfer on CE5.0 devices using USB BT ... Now i am able to search and pair it other devices using Bluetooth ... my bluetooth dongle. ...
    (microsoft.public.windowsce.platbuilder)
  • Need Help: USB Bluetooth Dongle support on CE5.0
    ... I am trying to use OBEX file transfer on CE5.0 devices using USB BT ... Now i am able to search and pair it other devices using Bluetooth ... Similarly i am trying with adding BT keyboard profile by including ... my bluetooth dongle. ...
    (microsoft.public.windowsce.platbuilder)
Loading