Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: "Tod Merley" <todbot88@xxxxxxxxx>
- Date: Sat, 15 Apr 2006 12:15:50 -0700
On 4/15/06, Debbie Deutsch <fedoralist@xxxxxxxxxxxx> wrote:
Lyvim Xaphir wrote:
Has this machine done any updates or is this the original binaries off
of the FC5 install cds?
Given the information you have gathered up to this point, I would put
the machine in runlevel 3 and then start experimenting with different X
resolutions. Unless that is the machine has gone thru updating.
LX
No, there were no updates. I've never been able to get past the
configuration procedure that happens when you boot the first time after
the install. The installation was off an unmodified FC5 distribution.
Since my previous email I reinstalled FC5 from scratch. Then I went
through the first boot configuration process, but this time I did NOT
alter my display settings or change the SELinux setting. I got the same
problem as before. The screen went grayish-blue, then blank, and the
system hung.
One other thing may be worth mentioning. The installation correctly
identified the graphics chipset on the motherboard and the monitor
model. However the initial display settings during the first boot were
600x800. This is almost certainly a lower resolution that was used
during the installation procedure. I don't remember the monitor coming
up with such a low resolution when I installed FC5 on my other Linux box.
This problem is baffling. I wonder if there is a log file somewhere
that might reveal something. I could boot into Linux rescue mode and
take a look, if I knew what to look for. :-)
Debbie
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Hi Debbie!
If it were me I would be doing the following:
1. Obtain the technical specifications on the monitor from the web.
2. Boot Linux (from CD) into rescue mode and print (or copy the monitor,
display sections) of /etc/X11/xorg.conf.
3. Might be well to do a "man xorg.conf" on a working linux machine. Anyway
check specifically the resolution and horizonal and vertical timeing to be
within that which the monitor will be happy with. A possible easier way may
be to boot a Knoppix CD and copy what it comes up with. Your monitor may
well be in the list that Fedora has during setup. I do not recall the setup
utility name (perhaps Craig White has provided this) but with the monitor
info you may well be able to select the best xorg.conf by selecting your
specific monitor from the setup facility.
All above done should eliminate X as a possible cause. It is my first
guess.
Good Hunting!
Tod
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
- Follow-Ups:
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: Debbie Deutsch
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- References:
- Problem booting FC5 after good install and doing the "first boot" configuration
- From: Debbie Deutsch
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: Timothy Murphy
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: Debbie Deutsch
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: Lyvim Xaphir
- Re: Problem booting FC5 after good install and doing the "first boot" configuration
- From: Debbie Deutsch
- Problem booting FC5 after good install and doing the "first boot" configuration
- Prev by Date: Re: Fedora Frog - problem solver for Fedora
- Next by Date: i810 bug in X11?
- Previous by thread: Re: Problem booting FC5 after good install and doing the "first boot" configuration
- Next by thread: Re: Problem booting FC5 after good install and doing the "first boot" configuration
- Index(es):
Relevant Pages
|
|
