Re: 2.6.0-test4-mm2: promise again fdisk causes Oops

From: Resident Boxholder (resid_at_boxho.com)
Date: 08/31/03

  • Next message: Felipe W Damasio: "[PATCH] Needed include in usb/gadget/net2280"
    Date:	Sat, 30 Aug 2003 20:57:29 -0400
    To: undisclosed-recipients: ;
    
    

    Peter,

    If you'd like to get a null modem cable and contribute logs about the
    promise that should help. If you'd like to get back to work, promise ide
    cards, uh, aren't great for linux right now. I switched to a siig card.

    "disabling the promise controller in bios", generally if you disable
    anything in bios and have linux code in the kernel for it, the thing
    will be found and enabled by linux until you take the relevent code out
    of your kernel or rip the card out of your box. You don't want to take
    the promise code out and have generic code make do, either, so try
    taking the card out!

    "promise controller", I started with two, took one and its cd's out,
    played with hdparm, disabled nforce2 ethernet and usb and serial and
    parallel and winmodem and audio(shame, it's the surround sound mcpt),
    disable apic so linux can enable it(!), finally took the promise card
    out and put in a Silicon Image 680 chip siig controller card. With the
    promise in the promise drives would crash the system in any config but I
    could run 32io unmask irq udma6 on mbo drives only with no errors. With
    the SiImage.c driver and SiI680 chip unmask off is needed(according to
    siimage.c doc, and IN FACT) also hdparm -d1 -c1 -p9 -u0 -X70 on the siig
    and still needed unmask off on the mbo controller to keep raid from
    crashing hdparm -d1 -c1 -p4 -u0 -X70 on the mbo controller. -u0 turns
    unmask off.

    Siig SiI680 chip works without errors on a four-drive linux software
    raid as long as I do the hdparms, bios turn off apic, usb, ethernet,
    audio, serial, parallel, winmodem, use a card for ethernet. Nvidia says
    set "non-pnp os" but I didn't find that helpful, had to turn onboard
    audio and ethernet off and pnp-os is on(kern 2.6.0-t4 MSI nforce2
    k7ndelta mbo amd xp 3000+ cpu pc3200csl2 ddr, 4 Maxtor 8mbcache 60G's,
    amd74xx driver on mbo controller and siimage.c on SiI680 card).

    I could crash both promise and SiI680 with fdisk, mke2fs, mkreiserfs,
    e2fsck, reiserfsck, mdadm -C, mdadm -A, but the relevent conflicts were
    hdparm -u0 the sii680 and conflicts between promise and sii680(cmd680)
    and usb and onboard ethernet and...there was no fix for promise but siig
    CAN work in a no-frills server setup.

    The usb code is being worked on as far as conflicts.

    cp -aR /usr /tmp should break the promise setup if it's going to break.

    -Bob D

    Peter Lieverdink wrote:

    > FYI: I can't reproduce this under 2.6.0-test4-mm3-1
    >
    > - Peter.
    > --
    > At 15:12 29/08/2003 +1000, you wrote:
    >
    >> Hi,
    >>
    >> When running fdisk -l under 2.6.0-test4-mm2, the kernel oopses. dmesg,
    >> the oops (fdisk.txt) and output from lspci are attached.
    >>
    >> I've tried after disabling the Promise controller in the BIOS, but the
    >> oops still occurs. Same when I specify a device instead of -l.
    >>
    >> fdisk is from debian/unstable, version 2.11z
    >>
    >> - Peter.
    >
    >

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/


  • Next message: Felipe W Damasio: "[PATCH] Needed include in usb/gadget/net2280"

    Relevant Pages

    • problem starting up Fedora on an IBM Thinkpad 600E using Xircom card
      ... Redhat Fedora working on my laptop. ... >> ethernet after booting. ... > network service before the pcmcia service. ... > card is recognized then you should be able to use it for networking. ...
      (comp.os.linux.setup)
    • Re: cPCI Hotplug support
      ... Card: Zynx ZX412 dual 10/100 card and DEC/Intel 21143 chipset ... media: Ethernet autoselect ... vendor = 'Digital Equipment Corporation' ... But these drivers don't work for me. ...
      (freebsd-current)
    • only first PCMCIA card works
      ... card is plugged on the first PCMCIA slot and I inserted my FC card ... second slot, be it ethernet card or FC card adapter, doesn't work. ... # Power management support ... <Parallel port bus> on ppc0 ...
      (freebsd-questions)
    • Re: 3Com 3C05 adapter on 43P running 4.3
      ... > card out, and the ent0 PCI adapter still shows up. ... So the on-board adapter goes through the PCI ... device driver for the OS to make it usable. ... ethernet card, or get a different ethernet adapter... ...
      (comp.unix.aix)
    • multiport ethernet cards
      ... going to buy a spare PCI ethernet card. ... except on Ebay (where I can now only see one two port card). ... These two multiport ethernet adapters deliver excellent performance at ...
      (Debian-User)