PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)
From: Pavel Alexeev (al_pavel_at_rambler.ru)
Date: 12/07/03
- Previous message: Dan Creswell: "Irq balancing problem?"
- Next in thread: Greg KH: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Reply: Greg KH: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Reply: Charles Bueche: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Sun, 07 Dec 2003 00:42:05 +0100 To: linux-kernel@vger.kernel.org
Hi!
Sorry, i am totally stumped as to whom to send the report :)
[1.] One line summary of the problem:
-------------------------------------
I cannot mount any USB mass storage drive when using kernel 2.6.0-test11
[2.] Full description of the problem/report:
--------------------------------------------
After plugging the HP Photosmart 720 USB cable in my notebook HP Omnibook xe4500 i see
in /var/log/messages:
Dec 6 19:28:18 mycomp kernel: hub 1-0:1.0: new USB device on port 2, assigned address 3
Dec 6 19:28:18 mycomp modprobe: FATAL: Module usb_storage already in kernel.
Dec 6 19:28:18 mycomp kernel: scsi1 : SCSI emulation for USB Mass Storage devices
Dec 6 19:28:18 mycomp scsi.agent[894]: bogus sysfs DEVPATH=/devices/pci0000:00/0000:00:02.0/usb1/1-2/1-2:1.0/ho st1/1:0:0:0
Dec 6 19:28:18 mycomp kernel: Vendor: Model: Rev:
Dec 6 19:28:18 mycomp kernel: Type: Direct-Access ANSI SCSI revision: 02
Dec 6 19:28:18 mycomp kernel: Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
But I cannot mount the device:
bash-2.05b# mount /dev/sg0 /mnt/flash
mount: /dev/sg0 is not a block device
bash-2.05b# mount /dev/sda1 /mnt/flash
mount: /dev/sda1 is not a valid block device
bash-2.05b# mount /dev/sdb1 /mnt/flash
mount: /dev/sdb1 is not a valid block device
...
When I use the 2.4.22 kernel (compiled with the same options in .config-file), the
command "mount /dev/sda1 /mnt/flash" works fine!
I have tried the same with the 128MB USB Flash Drive (noname). The contents of the /var/log/messages:
Dec 6 14:49:25 mycomp kernel: hub 1-0:1.0: new USB device on port 2, assigned address 2
Dec 6 14:49:25 mycomp kernel: Initializing USB Mass Storage driver...
Dec 6 14:49:26 mycomp kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Dec 6 14:49:26 mycomp scsi.agent[597]: bogus sysfs DEVPATH=/devices/pci0000:00/0000:00:02.0/usb1/1-2/1-2:1.0/ho st0/0:0:0:0
Dec 6 14:49:26 mycomp kernel: Vendor: Model: USB DISK Pro Rev: 1.09
Dec 6 14:49:26 mycomp kernel: Type: Direct-Access ANSI SCSI revision: 02
Dec 6 14:49:26 mycomp kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Dec 6 14:49:26 mycomp kernel: drivers/usb/core/usb.c: registered new driver usb-storage
Dec 6 14:49:26 mycomp kernel: USB Mass Storage support registered.
But when I do the same under 2.4.22, it works also fine! The output in /var/log/messages
when using 2.4.22:
Dec 6 12:26:05 mycomp kernel: hub.c: new USB device 00:02.0-2, assigned address 2
Dec 6 12:26:08 mycomp kernel: Initializing USB Mass Storage driver...
Dec 6 12:26:08 mycomp kernel: usb.c: registered new driver usb-storage
Dec 6 12:26:08 mycomp kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Dec 6 12:26:08 mycomp kernel: USB Mass Storage support registered.
Dec 6 12:29:30 mycomp kernel: sda: sda1
[3.] Keywords (i.e., modules, networking, kernel):
--------------------------------------------------
USB Mass Storage, kernel 2.6.0-test11, mount
[4.] Kernel version (from /proc/version):
-----------------------------------------
Linux version 2.6.0-test11 (gcc version 3.2.3)
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
-----------------------------------------------------------------------
No Oops.. message
[6.] A small shell script or example program which triggers the
problem (if possible)
---------------------------------------------------------------
Not possible :)
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
-------------------------------------------------------------
Linux Yozhikbook 2.6.0-test11 #9 Sat Dec 6 14:43:41 CET 2003 i686 unknown unknown GNU/Linux
Gnu C 3.2.3
Gnu make 3.80
util-linux 2.12
mount 2.12
module-init-tools 0.9.14
e2fsprogs 1.34
pcmcia-cs 3.2.5
PPP 2.4.1
nfs-utils 1.0.6
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Linux C++ Library 5.0.3
Procps 2.0.16
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded usb_storage radeon snd_pcm_oss snd_mixer_oss uhci_hcd ohci_hcd ehci_hcd usbcore
[7.2.] Processor information (from /proc/cpuinfo):
--------------------------------------------------
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz
stepping : 4
cpu MHz : 1699.976
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat p
se36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3342.33
[7.3.] Module information (from /proc/modules):
-----------------------------------------------
usb_storage 26368 0 - Live 0xd0914000
radeon 117400 2 - Live 0xd0937000
snd_pcm_oss 51844 0 - Live 0xd0906000
snd_mixer_oss 19072 1 snd_pcm_oss, Live 0xd08b5000
uhci_hcd 30344 0 - Live 0xd08ed000
ohci_hcd 17664 0 - Live 0xd08c2000
ehci_hcd 23552 0 - Live 0xd08bb000
usbcore 105684 6 usb_storage,uhci_hcd,ohci_hcd,ehci_hcd, Live 0xd08d2000
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
--------------------------------------------------------------------------
bash-2.05b# cat ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1000-10ff : 0000:00:06.0
1000-10ff : ALI 5451
1400-14ff : 0000:00:08.0
1800-180f : 0000:00:10.0
1800-1807 : ide0
1808-180f : ide1
1c00-1cff : 0000:00:12.0
1c00-1cff : eth0
4000-40ff : PCI CardBus #02
4400-44ff : PCI CardBus #02
4800-48ff : PCI CardBus #06
4c00-4cff : PCI CardBus #06
8000-803f : 0000:00:11.0
8040-805f : 0000:00:11.0
9000-9fff : PCI Bus #01
9000-90ff : 0000:01:00.0
bash-2.05b# cat iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000cf000-000cffff : Extension ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-0feeffff : System RAM
00100000-0039665c : Kernel code
0039665d-004be57f : Kernel data
0fef0000-0fefefff : ACPI Tables
0feff000-0fefffff : ACPI Non-volatile Storage
0ff00000-0fffffff : reserved
10000000-10000fff : 0000:00:0a.0
10000000-10000fff : yenta_socket
10001000-10001fff : 0000:00:0a.1
10001000-10001fff : yenta_socket
10400000-107fffff : PCI CardBus #02
10800000-10bfffff : PCI CardBus #02
10c00000-10ffffff : PCI CardBus #06
11000000-113fffff : PCI CardBus #06
e0000000-e0000fff : 0000:00:02.0
e0000000-e0000fff : ohci_hcd
e0001000-e0001fff : 0000:00:06.0
e0002000-e0002fff : 0000:00:08.0
e0003000-e00037ff : 0000:00:0c.0
e0003000-e00037ff : ohci1394
e0004000-e0007fff : 0000:00:0c.0
e0008000-e0008fff : 0000:00:12.0
e0008000-e0008fff : eth0
e0100000-e01fffff : PCI Bus #01
e0100000-e010ffff : 0000:01:00.0
e8000000-efffffff : PCI Bus #01
e8000000-efffffff : 0000:01:00.0
f0000000-f7ffffff : 0000:00:00.0
fffc0000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
---------------------------------------------
00:00.0 Host bridge: ALi Corporation M1671 Super P4 Northbridge [AGP4X,PCI and SDR/DDR] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [b0] AGP version 2.0
Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e0100000-e01fffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: ALi Corporation ALI M1533 Aladdin IV ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 Modem: ALi Corporation Intel 537 [M5457 AC-Link Modem] (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0002000 (32-bit, non-prefetchable) [disabled] [size=4K]
Region 1: I/O ports at 1400 [disabled] [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0003000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e0004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if b0)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 1800 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 Bridge: ALi Corporation M7101 PMU
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
Subsystem: Unknown device 3c08:a400
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 90 (2750ns min, 13000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: Memory at e0008000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=320mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=28 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
----------------------------------------------
Attached devices:
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: Model: USB DISK Pro Rev: 1.09
Type: Direct-Access ANSI SCSI revision: 02
Note: USB Flash inserted, HP Photosmart not inserted
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
-----------------------------------------------------------------
bash-2.05b# ls -lR /proc/scsi
/proc/scsi:
total 0
-r--r--r-- 1 root root 0 2003-12-07 00:27 device_info
-r--r--r-- 1 root root 0 2003-12-07 00:27 scsi
dr-xr-xr-x 2 root root 0 2003-12-07 00:27 sg
dr-xr-xr-x 2 root root 0 2003-12-07 00:27 usb-storage
/proc/scsi/sg:
total 0
-rw-r--r-- 1 root root 0 2003-12-07 00:27 allow_dio
-r--r--r-- 1 root root 0 2003-12-07 00:27 debug
-rw-r--r-- 1 root root 0 2003-12-07 00:27 def_reserved_size
-r--r--r-- 1 root root 0 2003-12-07 00:27 device_hdr
-r--r--r-- 1 root root 0 2003-12-07 00:27 device_strs
-r--r--r-- 1 root root 0 2003-12-07 00:27 devices
-r--r--r-- 1 root root 0 2003-12-07 00:27 version
/proc/scsi/usb-storage:
total 0
-rw-r--r-- 1 root root 0 2003-12-07 00:27 2
bash-2.05b# cat /proc/scsi/usb-storage/2
Host scsi2: usb-storage
Vendor:
Product: USB DISK Pro
Serial Number: 073B1C3000A4
Protocol: Transparent SCSI
Transport: Bulk
Quirks:
[X.] Other notes, patches, fixes, workarounds:
----------------------------------------------
I have no patches applied to the compiled kernel.
PCMCIA-cards (FAT file system) work fine! I can successfully mount these cards with
mount -t vfat /dev/hde1 /mnt/pcmcia
Best regards,
Pavel Alexeev
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Dan Creswell: "Irq balancing problem?"
- Next in thread: Greg KH: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Reply: Greg KH: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Reply: Charles Bueche: "Re: PROBLEM: (Bug report) USB Mass Storage in 2.6.0-test11 (cannot mount flash drive)"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
