2.6.6-rc3 scsi symbios prevents booting
From: Klaus Dittrich (kladit_at_t-online.de)
Date: 04/30/04
- Previous message: Maneesh Soni: "[RFC 1/2] kobject_set_name - error handling"
- Next in thread: Klaus Dittrich: "Re: 2.6.6-rc3 scsi symbios prevents booting"
- Maybe reply: Klaus Dittrich: "Re: 2.6.6-rc3 scsi symbios prevents booting"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 30 Apr 2004 12:42:29 +0200 To: linux mailing-list <linux-kernel@vger.kernel.org>
Booting kernel-2.6.6-rc3 hangs because of the Symbios scsi-driver.
No errors with kernel-2.6.5.
(Mobo Tyan S2665, Dawicontrol DC-2964F (Chip used is AM53C974)
I get this messages .. (copied by hand from bootscreen).
Beginning Domain Validation
sym0:5 FAST SCSI 10 MB/s ST (100.0ns,offset 15)
scsi(2:0:5:0) ECHO BUFFER SIZE 5924 ist too big, trimming to 4096
scsi(2:0:5:0) Domain Validation detected failure, dropping back.
sym0:5 FAST SCSI 6.8 MB/s ST (148.0ns,offset 15)
scsi(2:0:5:0) Domain Validation detected failure, dropping back.
sym0:5:0 asynchronous
# This appeares two times
sym0:5:0 ABORT OPERATION started
sym0:5:0 ABORT OPERATION timed out
sym0:5:0 BUS RESET started
sym0:5:0 BUS RESET timed out
sym0:5:0 DEVICE RESET started
sym0:5:0 DEVICE RESET timed out
The system then hangs.
In contrast to this the messages from from kernel-2.6.5.
No errors here. All scsi-devices are working.
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
(scsi0:A:9): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
(scsi0:A:10): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
Vendor: FUJITSU Model: MAP3367NC Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:9:0: Tagged Queuing enabled. Depth 32
Vendor: FUJITSU Model: MAP3367NC Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:10:0: Tagged Queuing enabled. Depth 32
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
sym0: <875> rev 0x4 at pci 0000:05:01.0 irq 22
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi2 : sym-2.1.18i
Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Vendor: EPSON Model: Perfection1640 Rev: 1.06
Type: Processor ANSI SCSI revision: 02
st: Version 20040318, fixed bufsize 32768, s/g segs 256
SCSI device sda: 71775284 512-byte hdwr sectors (36749 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 9, lun 0
SCSI device sdb: 71775284 512-byte hdwr sectors (36749 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi0, channel 0, id 10, lun 0
sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 16)
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 2, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 9, lun 0, type 0
Attached scsi generic sg1 at scsi0, channel 0, id 10, lun 0, type 0
Attached scsi generic sg2 at scsi2, channel 0, id 2, lun 0, type 5
Attached scsi generic sg3 at scsi2, channel 0, id 5, lun 0, type 3
Hope this helps to find the bug(s).
-- Klaus - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Maneesh Soni: "[RFC 1/2] kobject_set_name - error handling"
- Next in thread: Klaus Dittrich: "Re: 2.6.6-rc3 scsi symbios prevents booting"
- Maybe reply: Klaus Dittrich: "Re: 2.6.6-rc3 scsi symbios prevents booting"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
