Promise Ultra Track RM15000 + aic7xxx
From: Adams, Bill TQO (badams_at_tqs.com)
Date: 07/20/04
- Previous message: Benjamin Herrenschmidt: "Re: device_suspend() levels [was Re: [patch] ACPI work on aic7xxx]"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
To: linux-kernel@vger.kernel.org Date: Tue, 20 Jul 2004 14:14:16 -0700
linux 2.4.26 stock kernel
I have a Promise Ultra Track RM15000 which is basically a IDE<->SCSI
RAID enclosure. It is running the latest firmware 1.10.0.19. You can
read all about it here:
http://www.promise.com/product/product_detail_eng.asp?productId=109&familyId=6
This is connected to an Adaptec 29160 with the latest firmware 3.10.0.
Whether I am formatting a partition as a MySQL InnoDB raw or as ext3, it
gives many errors. On the ext3 format, the badblocks command is what
elucidates the problems.
mkfs -j /dev/sdb1 -T largefile4 -v -c -c
which runs
badblocks -b 4096 -s -w /dev/sdb1 170897454
The errors seem to happen in random places of the badblocks check each
time I try the sequence:
modprobe aic7xxx aic7xxx='random options"
mkfs -j /dev/sdb1 -T largefile4 -v -c -c
rmmod aic7xxx
I have tried both periodic_otag and periodic_otag.extended along with
"verbose.tag_info:{{16.16.16}}" and nothing seems to make a difference.
I have another system with three Adaptec 3960D controllers connected to
winchester systems raid enclosures. This system has the same version
aic7xxx driver (6.2.36) and has no problems so I seriously doubt it is
the driver.
I have pasted in some of the logs below so that search engines can find
them ('cause I don't get enough spam as it is) and have also attached a
.tgz of the log files since my email client will probably mangle the
formatting of the pasted in logs.
Any insight, suggestions, or help would be greatly appreciated. Please
cc me as I am not on the list.
And of course I am happy to provide further information.
--Bill Adams
Three bits of info follow, the output from /proc/scsi/aic7xxx/1; the
syslog for the module load; and a section of the syslog showing some of
the scsi errors.
=-=-=-=-=-=-=-=
Log for cat /proc/scsi/aic7xxx/1
Adaptec AIC7xxx driver version: 6.2.36
Adaptec 29160 Ultra160 SCSI adapter
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Allocated SCBs: 18, SG List Length: 85
Serial EEPROM:
0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a
0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a
0x08f4 0x7c5d 0x2807 0x0010 0x0300 0xffff 0xffff 0xffff
0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x0250 0xe64f
Target 0 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Goal: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Curr: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Channel A Target 0 Lun 0 Settings
Commands Queued 7055
Commands Active 13
Command Openings 3
Max Tagged Openings 16
Device Queue Frozen Count 0
Target 1 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Goal: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Curr: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Channel A Target 1 Lun 0 Settings
Commands Queued 6
Commands Active 0
Command Openings 16
Max Tagged Openings 16
Device Queue Frozen Count 0
Target 2 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Goal: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Curr: 160.000MB/s transfers (80.000MHz DT, offset 62, 16bit)
Channel A Target 2 Lun 0 Settings
Commands Queued 3
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Target 3 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 4 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 5 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 6 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 7 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 8 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 9 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 10 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 11 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 12 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 13 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 14 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Target 15 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
=-=-=-=-=-=-=-=-=-=
Log for modprobe aic7xxx
aic7xxx='verbose.periodic_otag.extended.tag_info:{{16.16.16}}'
Jul 20 16:11:06 host kernel: tag_info[0:0] = 16
Jul 20 16:11:06 host kernel: tag_info[0:1] = 16
Jul 20 16:11:06 host kernel: tag_info[0:2] = 16
Jul 20 16:11:06 host kernel: PCI: Enabling device 01:06.0 (0116 -> 0117)
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Enabling 39Bit Addressing
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Reading SEEPROM...done.
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: BIOS eeprom is present
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Secondary High byte
termination Enabled
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Secondary Low byte
termination Enabled
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Primary Low Byte termination
Enabled
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Primary High Byte
termination Enabled
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Downloading Sequencer
Program... 432 instructions downloaded
Jul 20 16:11:06 host kernel: ahc_pci:1:6:0: Features 0x1def6, Bugs 0x40,
Flags 0x21485540
Jul 20 16:11:06 host kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI
HBA DRIVER, Rev 6.2.36
Jul 20 16:11:06 host kernel: <Adaptec 29160 Ultra160 SCSI
adapter>
Jul 20 16:11:06 host kernel: aic7892: Ultra160 Wide Channel A,
SCSI Id=7, 32/253 SCBs
Jul 20 16:11:06 host kernel:
Jul 20 16:11:06 host kernel: blk: queue c8c16018, I/O limit 524287Mb
(mask 0x7fffffffff)
Jul 20 16:11:21 host kernel: (scsi1:A:0:0): Sending PPR bus_width 1,
period 9, offset 7f, ppr_options 2
Jul 20 16:11:21 host kernel: (scsi1:A:0:0): Received PPR width 1, period
9, offset 3e,options 2
Jul 20 16:11:21 host kernel: ^IFiltered to width 1, period 9, offset 3e,
options 2
Jul 20 16:11:21 host kernel: (scsi1:A:0): 6.600MB/s transfers (16bit)
Jul 20 16:11:21 host kernel: scsi1: target 0 using 16bit transfers
Jul 20 16:11:21 host kernel: (scsi1:A:0): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:21 host kernel: scsi1: target 0 synchronous at 80.0MHz DT,
offset = 0x3e
Jul 20 16:11:21 host kernel: (scsi1:A:1:0): Sending PPR bus_width 1,
period 9, offset 7f, ppr_options 2
Jul 20 16:11:21 host kernel: (scsi1:A:1:0): Received PPR width 1, period
9, offset 3e,options 2
Jul 20 16:11:21 host kernel: ^IFiltered to width 1, period 9, offset 3e,
options 2
Jul 20 16:11:21 host kernel: (scsi1:A:1): 6.600MB/s transfers (16bit)
Jul 20 16:11:21 host kernel: scsi1: target 1 using 16bit transfers
Jul 20 16:11:21 host kernel: (scsi1:A:1): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:21 host kernel: scsi1: target 1 synchronous at 80.0MHz DT,
offset = 0x3e
Jul 20 16:11:21 host kernel: (scsi1:A:2:0): Sending PPR bus_width 1,
period 9, offset 7f, ppr_options 2
Jul 20 16:11:21 host kernel: (scsi1:A:2:0): Received PPR width 1, period
9, offset 3e,options 2
Jul 20 16:11:21 host kernel: ^IFiltered to width 1, period 9, offset 3e,
options 2
Jul 20 16:11:21 host kernel: (scsi1:A:2): 6.600MB/s transfers (16bit)
Jul 20 16:11:21 host kernel: scsi1: target 2 using 16bit transfers
Jul 20 16:11:21 host kernel: (scsi1:A:2): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:21 host kernel: scsi1: target 2 synchronous at 80.0MHz DT,
offset = 0x3e
Jul 20 16:11:24 host kernel: Vendor: Promise Model: 8 Disk
RAID5 Rev: 1.10
Jul 20 16:11:24 host kernel: Type:
Direct-Access ANSI SCSI revision: 03
Jul 20 16:11:24 host kernel: blk: queue e1671e18, I/O limit 524287Mb
(mask 0x7fffffffff)
Jul 20 16:11:24 host kernel: Vendor: Promise Model: 7 Disk
RAID5 Rev: 1.10
Jul 20 16:11:24 host kernel: Type:
Direct-Access ANSI SCSI revision: 03
Jul 20 16:11:24 host kernel: blk: queue cb8e0818, I/O limit 524287Mb
(mask 0x7fffffffff)
Jul 20 16:11:24 host kernel: Vendor: Promise Model: RAID
Console Rev: 1.00
Jul 20 16:11:24 host kernel: Type:
Processor ANSI SCSI revision: 03
Jul 20 16:11:24 host kernel: blk: queue d2172e18, I/O limit 524287Mb
(mask 0x7fffffffff)
Jul 20 16:11:27 host kernel: (scsi1:A:0): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:27 host kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth
16
Jul 20 16:11:27 host kernel: (scsi1:A:1): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:27 host kernel: scsi1:A:1:0: Tagged Queuing enabled. Depth
16
Jul 20 16:11:27 host kernel: (scsi1:A:2): 160.000MB/s transfers
(80.000MHz DT, offset 62, 16bit)
Jul 20 16:11:27 host kernel: Attached scsi disk sdb at scsi1, channel 0,
id 0, lun 0
Jul 20 16:11:27 host kernel: Attached scsi disk sdc at scsi1, channel 0,
id 1, lun 0
Jul 20 16:11:27 host kernel: SCSI device sdb: 4101561856 512-byte hdwr
sectors (2100000 MB)
Jul 20 16:11:27 host kernel: sdb: sdb1 sdb2 sdb3
Jul 20 16:11:27 host kernel: SCSI device sdc: 3515624448 512-byte hdwr
sectors (1800000 MB)
Jul 20 16:11:27 host kernel: sdc: sdc1 sdc2
=-=-=-=-=-=-=-=-=-=-=-=
Syslog Entry With Errors
Jul 20 16:00:41 host kernel: scsi1:0:0:0: Attempting to queue an ABORT
message
Jul 20 16:00:41 host kernel: CDB: 0x2a 0x0 0x1 0x5d 0xbf 0x7f 0x0 0x2
0x78 0x0
Jul 20 16:00:41 host kernel: scsi1: At time of recovery, card was not
paused
Jul 20 16:00:41 host kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Jul 20 16:00:41 host kernel: scsi1: Dumping Card State while idle, at
SEQADDR 0x8
Jul 20 16:00:41 host kernel: Card was paused
Jul 20 16:00:41 host kernel: ACCUM = 0x4, SINDEX = 0x64, DINDEX = 0x65,
ARG_2 = 0x3
Jul 20 16:00:41 host kernel: HCNT = 0x0 SCBPTR = 0x1
Jul 20 16:00:41 host kernel: SCSIPHASE[0x0] SCSISIGI[0x0] ERROR[0x0]
SCSIBUSL[0x0]
Jul 20 16:00:41 host kernel: LASTPHASE[0x1] SCSISEQ[0x12] SBLKCTL[0xa]
SCSIRATE[0x0]
Jul 20 16:00:41 host kernel: SEQCTL[0x10] SEQ_FLAGS[0xc0] SSTAT0[0x0]
SSTAT1[0x8]
Jul 20 16:00:41 host kernel: SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]
SIMODE1[0xa4]
Jul 20 16:00:41 host kernel: SXFRCTL0[0x80] DFCNTRL[0x0] DFSTATUS[0x89]
Jul 20 16:00:41 host kernel: STACK: 0xe8 0x16a 0x17f 0x3
Jul 20 16:00:41 host kernel: SCB count = 18
Jul 20 16:00:42 host kernel: Kernel NEXTQSCB = 5
Jul 20 16:00:42 host kernel: Card NEXTQSCB = 5
Jul 20 16:00:42 host kernel: QINFIFO entries:
Jul 20 16:00:42 host kernel: Waiting Queue entries:
Jul 20 16:00:43 host kernel: Disconnected Queue entries: 1:14 6:2 11:9
10:16 14:13 9:11 8:3 2:15 4:10 0:8 7:7 3:6 15:1 5:4 12:0 13:17
Jul 20 16:00:43 host kernel: QOUTFIFO entries:
Jul 20 16:00:43 host kernel: Sequencer Free SCB List: 16 17 18 19 20 21
22 23 24 25 26 27 28 29 30 31
Jul 20 16:00:44 host kernel: Sequencer SCB Info:
Jul 20 16:00:44 host kernel: 0 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x8]
Jul 20 16:00:44 host kernel: 1 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xe]
Jul 20 16:00:44 host kernel: 2 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xf]
Jul 20 16:00:44 host kernel: 3 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x6]
Jul 20 16:00:44 host kernel: 4 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xa]
Jul 20 16:00:44 host kernel: 5 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x4]
Jul 20 16:00:44 host kernel: 6 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x2]
Jul 20 16:00:44 host kernel: 7 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x7]
Jul 20 16:00:44 host kernel: 8 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x3]
Jul 20 16:00:44 host kernel: 9 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xb]
Jul 20 16:00:44 host kernel: 10 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x10]
Jul 20 16:00:45 host kernel: 11 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x9]
Jul 20 16:00:45 host kernel: 12 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x0]
Jul 20 16:00:45 host kernel: 13 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x11]
Jul 20 16:00:46 host kernel: 14 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xd]
Jul 20 16:00:46 host kernel: 15 SCB_CONTROL[0x64] SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x1]
Jul 20 16:00:47 host kernel: 16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:47 host kernel: 17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:48 host kernel: 18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:48 host kernel: 19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:48 host kernel: 20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:49 host kernel: 21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:49 host kernel: 22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:49 host kernel: 23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:50 host kernel: 24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:50 host kernel: 25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:50 host kernel: 26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:50 host kernel: 27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:50 host kernel: 28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:51 host kernel: 29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:51 host kernel: 30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:51 host kernel: 31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Jul 20 16:00:51 host kernel: Pending list:
Jul 20 16:00:51 host kernel: 14 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 2 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 9 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 16 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 13 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 11 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 3 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 15 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 10 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 8 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 7 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 6 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 1 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 4 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 0 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: 17 SCB_CONTROL[0x60] SCB_SCSIID[0x7]
SCB_LUN[0x0]
Jul 20 16:00:52 host kernel: Kernel Free SCB list: 12
Jul 20 16:00:52 host kernel: DevQ(0:0:0): 0 waiting
Jul 20 16:00:52 host kernel: DevQ(0:1:0): 0 waiting
Jul 20 16:00:52 host kernel: DevQ(0:2:0): 0 waiting
Jul 20 16:00:52 host kernel:
Jul 20 16:00:52 host kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Jul 20 16:00:52 host kernel: (scsi1:A:0:0): Device is disconnected,
re-queuing SCB
Jul 20 16:00:52 host kernel: Recovery code sleeping
Jul 20 16:00:52 host kernel: (scsi1:A:0:0): Abort Tag Message Sent
Jul 20 16:00:52 host kernel: (scsi1:A:0:0): SCB 1 - Abort Tag Completed.
Jul 20 16:00:52 host kernel: Recovery SCB completes
Jul 20 16:00:52 host kernel: Recovery code awake
Jul 20 16:00:52 host kernel: aic7xxx_abort returns 0x2002
Jul 20 16:00:52 host kernel: scsi1:0:0:0: Attempting to queue an ABORT
message
Jul 20 16:00:52 host kernel: CDB: 0x2a 0x0 0x1 0x5d 0xc1 0xf7 0x0 0x1
0x6a 0x0
Jul 20 16:00:52 host kernel: scsi1:0:0:0: Command not found
Jul 20 16:00:52 host kernel: aic7xxx_abort returns 0x2002
Jul 20 16:00:52 host kernel: scsi1:0:0:0: Attempting to queue an ABORT
message
Jul 20 16:00:52 host kernel: CDB: 0x2a 0x0 0x1 0x5d 0xc3 0x79 0x0 0x0
0x20 0x0
Jul 20 16:00:52 host kernel: scsi1:0:0:0: Command not found
Jul 20 16:00:52 host kernel: aic7xxx_abort returns 0x2002
Jul 20 16:01:18 host kernel: scsi1:0:0:0: Attempting to queue an ABORT
message
Jul 20 16:01:18 host kernel: CDB: 0x2a 0x0 0x1 0x5d 0x9c 0xb9 0x0 0x0
0x40 0x0
Jul 20 16:01:18 host kernel: scsi1:0:0:0: Command not found
Jul 20 16:01:18 host kernel: aic7xxx_abort returns 0x2002
Jul 20 16:01:18 host kernel: scsi1:0:0:0: Attempting to queue an ABORT
message
Jul 20 16:01:18 host kernel: CDB: 0x2a 0x0 0x1 0x5d 0xc3 0x99 0x0 0x2
0x9e 0x0
Jul 20 16:01:18 host kernel: scsi1:0:0:0: Command not found
[and more]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- application/x-compressed-tar attachment: badams_logs.tgz
- Previous message: Benjamin Herrenschmidt: "Re: device_suspend() levels [was Re: [patch] ACPI work on aic7xxx]"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
