Re: SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected
From: micah milano (micaho_at_gmail.com)
Date: 09/25/04
- Previous message: Stephan Dreyer: "Get ip before accept"
- In reply to: micah milano: "SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Next in thread: Bartlomiej Zolnierkiewicz: "Re: SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Reply: Bartlomiej Zolnierkiewicz: "Re: SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Sat, 25 Sep 2004 16:03:15 -0500 To: linux-kernel@vger.kernel.org
Some interesting additional information... if I boot with 2.4.25, the
CHS in the dmesg changes to something else, in 2.6.7 it was
CHS=65535/16/63, in 2.4.25 it becomes CHS=238216/16/63.
Looking at what fdisk finds, they are different again:
fdisk -l /dev/hde
Disk /dev/hde: 122.9 GB, 122942324736 bytes
255 heads, 63 sectors/track, 14946 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
fdisk -l /dev/hdg
Disk /dev/hdg: 122.9 GB, 122942324736 bytes
16 heads, 63 sectors/track, 238216 cylinders
Units = cylinders of 1008 * 512 = 516096 bytes
Dmesg from 2.4.25:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
ICH3: IDE controller at PCI slot 00:1f.1
ICH3: chipset revision 2
ICH3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2060-0x2067, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2068-0x206f, BIOS settings: hdc:pio, hdd:pio
SiI3112 Serial ATA: IDE controller at PCI slot 03:02.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: not 100% native mode: will probe irqs later
ide2: MMIO-DMA , BIOS settings: hde:DMA, hdf:DMA
ide3: MMIO-DMA , BIOS settings: hdg:DMA, hdh:DMA
SiI3112 Serial ATA: IDE controller at PCI slot 03:03.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: not 100% native mode: will probe irqs later
ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio
ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio
hdc: CD-224E, ATAPI CD/DVD-ROM drive
hde: Maxtor 6Y120M0, ATA DISK drive
blk: queue f8826d08, I/O limit 4095Mb (mask 0xffffffff)
hdg: Maxtor 6Y120M0, ATA DISK drive
blk: queue f882715c, I/O limit 4095Mb (mask 0xffffffff)
hdi: no response (status = 0xfe)
hdk: no response (status = 0xfe)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xf8879080-0xf8879087,0xf887908a on irq 26
ide3 at 0xf88790c0-0xf88790c7,0xf88790ca on irq 26
hde: attached ide-disk driver.
hde: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=238216/16/63
hdg: attached ide-disk driver.
hdg: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=238216/16/63
Partition check:
/dev/ide/host2/bus0/target0/lun0: [PTBL] [14946/255/63] p1 p2 p3 < p5 p6 p7 p8
p9 >/dev/ide/host2/bus1/target0/lun0:
Dmesg from 2.6.7:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3: IDE controller at PCI slot 0000:00:1f.1
ICH3: chipset revision 2
ICH3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2060-0x2067, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2068-0x206f, BIOS settings: hdc:pio, hdd:pio
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SiI3112 Serial ATA: IDE controller at PCI slot 0000:03:02.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: 100% native mode on irq 26
ide2: MMIO-DMA , BIOS settings: hde:DMA, hdf:DMA
ide3: MMIO-DMA , BIOS settings: hdg:DMA, hdh:DMA
hde: Maxtor 6Y120M0, ATA DISK drive
ide2 at 0xf8858080-0xf8858087,0xf885808a on irq 26
hdg: Maxtor 6Y120M0, ATA DISK drive
ide3 at 0xf88580c0-0xf88580c7,0xf88580ca on irq 26
SiI3112 Serial ATA: IDE controller at PCI slot 0000:03:03.0
SiI3112 Serial ATA: chipset revision 2
SiI3112 Serial ATA: 100% native mode on irq 27
ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio
ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio
hdi: no response (status = 0xfe)
hdk: no response (status = 0xfe)
hdi: no response (status = 0xfe), resetting drive
hdi: no response (status = 0xfe)
hdk: no response (status = 0xfe), resetting drive
hdk: no response (status = 0xfe)
hde: max request size: 64KiB
hde: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63
/dev/ide/host2/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 >
hdg: max request size: 64KiB
hdg: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63
/dev/ide/host2/bus1/target0/lun0:
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Additionally, here is my 2.6.7 kernel config:
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_STANDALONE=y
CONFIG_BROKEN_ON_SMP=y
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_ALIGNMENT_16=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_MICROCODE=y
# CONFIG_X86_MSR is not set
CONFIG_X86_CPUID=y
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
CONFIG_MATH_EMULATION=y
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_REGPARM is not set
#
# Power management options (ACPI, APM)
#
# CONFIG_PM is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_ASUS=y
CONFIG_ACPI_TOSHIBA=y
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_X86_PM_TIMER is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCI_USE_VECTOR is not set
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_CARMEL is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
# CONFIG_LBD is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_IDE_TASKFILE_IO is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIIMAGE=y
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_MEGARAID is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_SVW is not set
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
CONFIG_SCSI_SATA_SIL=y
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID5=y
# CONFIG_MD_RAID6 is not set
CONFIG_MD_MULTIPATH=y
CONFIG_BLK_DEV_DM=y
CONFIG_DM_CRYPT=y
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
CONFIG_IPMI_SOCKET=y
CONFIG_NET_KEY=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_NAT=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_TOS=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
CONFIG_INET6_IPCOMP=y
CONFIG_IPV6_TUNNEL=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=y
CONFIG_IP_NF_FTP=y
CONFIG_IP_NF_IRC=y
CONFIG_IP_NF_TFTP=y
CONFIG_IP_NF_AMANDA=y
CONFIG_IP_NF_QUEUE=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_IPRANGE=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_RECENT=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_DSCP=y
CONFIG_IP_NF_MATCH_AH_ESP=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_MATCH_TCPMSS=y
# CONFIG_IP_NF_MATCH_STEALTH is not set
CONFIG_IP_NF_MATCH_HELPER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_CONNTRACK=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
# CONFIG_IP_NF_TARGET_NETMAP is not set
CONFIG_IP_NF_TARGET_SAME=y
CONFIG_IP_NF_NAT_LOCAL=y
CONFIG_IP_NF_NAT_SNMP_BASIC=y
CONFIG_IP_NF_NAT_IRC=y
CONFIG_IP_NF_NAT_FTP=y
CONFIG_IP_NF_NAT_TFTP=y
CONFIG_IP_NF_NAT_AMANDA=y
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_DSCP=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_CLASSIFY=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
CONFIG_IP_NF_ARP_MANGLE=y
# CONFIG_IP_NF_RAW is not set
#
# IPv6: Netfilter Configuration
#
CONFIG_IP6_NF_QUEUE=y
CONFIG_IP6_NF_IPTABLES=y
CONFIG_IP6_NF_MATCH_LIMIT=y
CONFIG_IP6_NF_MATCH_MAC=y
CONFIG_IP6_NF_MATCH_RT=y
CONFIG_IP6_NF_MATCH_OPTS=y
CONFIG_IP6_NF_MATCH_FRAG=y
CONFIG_IP6_NF_MATCH_HL=y
CONFIG_IP6_NF_MATCH_MULTIPORT=y
CONFIG_IP6_NF_MATCH_OWNER=y
CONFIG_IP6_NF_MATCH_MARK=y
CONFIG_IP6_NF_MATCH_IPV6HEADER=y
CONFIG_IP6_NF_MATCH_AHESP=y
CONFIG_IP6_NF_MATCH_LENGTH=y
CONFIG_IP6_NF_MATCH_EUI64=y
CONFIG_IP6_NF_FILTER=y
CONFIG_IP6_NF_TARGET_LOG=y
CONFIG_IP6_NF_MANGLE=y
CONFIG_IP6_NF_TARGET_MARK=y
# CONFIG_IP6_NF_RAW is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CBQ=y
CONFIG_NET_SCH_HTB=y
CONFIG_NET_SCH_HFSC=y
# CONFIG_NET_SCH_CSZ is not set
CONFIG_NET_SCH_PRIO=y
CONFIG_NET_SCH_RED=y
CONFIG_NET_SCH_SFQ=y
CONFIG_NET_SCH_TEQL=y
CONFIG_NET_SCH_TBF=y
CONFIG_NET_SCH_GRED=y
CONFIG_NET_SCH_DSMARK=y
# CONFIG_NET_SCH_DELAY is not set
CONFIG_NET_SCH_INGRESS=y
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_TCINDEX=y
CONFIG_NET_CLS_ROUTE4=y
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=y
CONFIG_NET_CLS_U32=y
CONFIG_NET_CLS_RSVP=y
CONFIG_NET_CLS_RSVP6=y
CONFIG_NET_CLS_POLICE=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
# CONFIG_E1000_NAPI is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
CONFIG_SHAPER=y
# CONFIG_NETCONSOLE is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
CONFIG_SERIO_PCIPS2=y
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_MULTIPORT=y
CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_QIC02_TAPE is not set
#
# IPMI
#
CONFIG_IPMI_HANDLER=y
CONFIG_IPMI_PANIC_EVENT=y
CONFIG_IPMI_PANIC_STRING=y
CONFIG_IPMI_DEVICE_INTERFACE=y
CONFIG_IPMI_SI=y
CONFIG_IPMI_SMB=y
CONFIG_IPMI_WATCHDOG=y
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCF=y
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
CONFIG_I2C_PIIX4=y
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
CONFIG_SCx200_ACB=y
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
#
# Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
#
# Other I2C Chip support
#
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_PCI_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
#
# Logo configuration
#
# CONFIG_LOGO is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
#
# DOS/FAT/NT Filesystems
#
# CONFIG_FAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_DEVFS_FS=y
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS_XATTR=y
# CONFIG_DEVPTS_FS_SECURITY is not set
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_EXPORTFS is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=y
CONFIG_NLS_CODEPAGE_775=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_CODEPAGE_852=y
CONFIG_NLS_CODEPAGE_855=y
CONFIG_NLS_CODEPAGE_857=y
CONFIG_NLS_CODEPAGE_860=y
CONFIG_NLS_CODEPAGE_861=y
CONFIG_NLS_CODEPAGE_862=y
CONFIG_NLS_CODEPAGE_863=y
CONFIG_NLS_CODEPAGE_864=y
CONFIG_NLS_CODEPAGE_865=y
CONFIG_NLS_CODEPAGE_866=y
CONFIG_NLS_CODEPAGE_869=y
CONFIG_NLS_CODEPAGE_936=y
CONFIG_NLS_CODEPAGE_950=y
CONFIG_NLS_CODEPAGE_932=y
CONFIG_NLS_CODEPAGE_949=y
CONFIG_NLS_CODEPAGE_874=y
CONFIG_NLS_ISO8859_8=y
CONFIG_NLS_CODEPAGE_1250=y
CONFIG_NLS_CODEPAGE_1251=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=y
CONFIG_NLS_ISO8859_3=y
CONFIG_NLS_ISO8859_4=y
CONFIG_NLS_ISO8859_5=y
CONFIG_NLS_ISO8859_6=y
CONFIG_NLS_ISO8859_7=y
CONFIG_NLS_ISO8859_9=y
CONFIG_NLS_ISO8859_13=y
CONFIG_NLS_ISO8859_14=y
CONFIG_NLS_ISO8859_15=y
CONFIG_NLS_KOI8_R=y
CONFIG_NLS_KOI8_U=y
CONFIG_NLS_UTF8=y
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_SLAB=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
#
# Grsecurity
#
CONFIG_GRKERNSEC=y
# CONFIG_GRKERNSEC_LOW is not set
# CONFIG_GRKERNSEC_MEDIUM is not set
# CONFIG_GRKERNSEC_HIGH is not set
CONFIG_GRKERNSEC_CUSTOM=y
#
# Address Space Protection
#
# CONFIG_GRKERNSEC_KMEM is not set
# CONFIG_GRKERNSEC_IO is not set
CONFIG_GRKERNSEC_PROC_MEMMAP=y
CONFIG_GRKERNSEC_BRUTE=y
CONFIG_GRKERNSEC_HIDESYM=y
#
# Role Based Access Control Options
#
CONFIG_GRKERNSEC_ACL_HIDEKERN=y
CONFIG_GRKERNSEC_ACL_MAXTRIES=3
CONFIG_GRKERNSEC_ACL_TIMEOUT=30
#
# Filesystem Protections
#
CONFIG_GRKERNSEC_PROC=y
CONFIG_GRKERNSEC_PROC_USER=y
# CONFIG_GRKERNSEC_PROC_ADD is not set
CONFIG_GRKERNSEC_LINK=y
CONFIG_GRKERNSEC_FIFO=y
# CONFIG_GRKERNSEC_CHROOT is not set
#
# Kernel Auditing
#
# CONFIG_GRKERNSEC_AUDIT_GROUP is not set
# CONFIG_GRKERNSEC_EXECLOG is not set
CONFIG_GRKERNSEC_RESLOG=y
# CONFIG_GRKERNSEC_CHROOT_EXECLOG is not set
# CONFIG_GRKERNSEC_AUDIT_CHDIR is not set
CONFIG_GRKERNSEC_AUDIT_MOUNT=y
# CONFIG_GRKERNSEC_AUDIT_IPC is not set
CONFIG_GRKERNSEC_SIGNAL=y
CONFIG_GRKERNSEC_FORKFAIL=y
CONFIG_GRKERNSEC_TIME=y
# CONFIG_GRKERNSEC_PROC_IPADDR is not set
#
# Executable Protections
#
CONFIG_GRKERNSEC_EXECVE=y
CONFIG_GRKERNSEC_DMESG=y
CONFIG_GRKERNSEC_RANDPID=y
# CONFIG_GRKERNSEC_TPE is not set
#
# Network Protections
#
CONFIG_GRKERNSEC_RANDNET=y
CONFIG_GRKERNSEC_RANDISN=y
CONFIG_GRKERNSEC_RANDID=y
CONFIG_GRKERNSEC_RANDSRC=y
CONFIG_GRKERNSEC_RANDRPC=y
# CONFIG_GRKERNSEC_SOCKET is not set
#
# Sysctl support
#
CONFIG_GRKERNSEC_SYSCTL=y
#
# Logging Options
#
CONFIG_GRKERNSEC_FLOODTIME=10
CONFIG_GRKERNSEC_FLOODBURST=4
#
# PaX
#
CONFIG_PAX=y
#
# PaX Control
#
CONFIG_PAX_SOFTMODE=y
# CONFIG_PAX_EI_PAX is not set
CONFIG_PAX_PT_PAX_FLAGS=y
CONFIG_PAX_NO_ACL_FLAGS=y
# CONFIG_PAX_HAVE_ACL_FLAGS is not set
# CONFIG_PAX_HOOK_ACL_FLAGS is not set
#
# Non-executable pages
#
# CONFIG_PAX_NOEXEC is not set
#
# Address Space Layout Randomization
#
CONFIG_PAX_ASLR=y
# CONFIG_PAX_RANDKSTACK is not set
CONFIG_PAX_RANDUSTACK=y
CONFIG_PAX_RANDMMAP=y
# CONFIG_PAX_NOVSYSCALL is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
# CONFIG_CRYPTO_ARC4 is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Library routines
#
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_STD_RESOURCES=y
CONFIG_PC=y
On Sat, 25 Sep 2004 14:14:09 -0500, micah milano <micaho@gmail.com> wrote:
> I've got two Maxtor 6Y120M0 drives, same firmware, but they show up
> with differing CHS when I attempt to partition them, however it seems
> like other places on the system they are detected as having the same
> properties. This is making setting up software raid-1 difficult.
> Should I boot with a particular geometry specified on the kernel line
> to make it correct?
>
> Using fdisk -l on each disk you see that one reports 255 heads, 63
> sectors/track, 14946 cylinders and the other reports 16 heads, 63
> sectors/track, 238216 cylinders.
>
> This is 2.6.7 (i'm here because the ipmi software from supermicro is
> not working for 2.6.8 yet), and I am not able to follow this list, so
> please CC me on any reply. I've tried to include all the useful
> information, but if I neglected something, please let me know and I
> will provide it right away.
>
> Thanks for any insight, this is driving me a little batty,
> micah
>
> fdisk -l /dev/hde
>
> Disk /dev/hde: 122.9 GB, 122942324736 bytes
> 255 heads, 63 sectors/track, 14946 cylinders
> Units = cylinders of 16065 * 512 = 8225280 bytes
>
> fdisk -l /dev/hdg
>
> Disk /dev/hdg: 122.9 GB, 122942324736 bytes
> 16 heads, 63 sectors/track, 238216 cylinders
> Units = cylinders of 1008 * 512 = 516096 bytes
>
> parted says:
>
> parted /dev/hde
> Error: The partition table on /dev/hde is inconsistent. There are many reasons
> why this might be the case. However, the most likely reason is that Linux
> detected the BIOS geometry for /dev/hde incorrectly. GNU Parted suspects the
> real geometry should be 14946/255/63 (not 238216/16/63). You should check with
> your BIOS first, as this may not be correct. You can inform Linux by adding the
> parameter hde=14946,255,63 to the command line. See the LILO or GRUB
> Information: The operating system thinks the geometry on /dev/hde is
> 238216/16/63. Therefore, cylinder 1024 ends at 503.999M.
>
> parted /dev/hdg (no error):
> Using /dev/hdg
> Information: The operating system thinks the geometry on /dev/hdg is
> 238216/16/63. Therefore, cylinder 1024 ends at 503.999M.
>
> cat /proc/ide/piix
>
> Controller: 0
>
> Intel PIIX4 Ultra 100 Chipset.
> --------------- Primary Channel ---------------- Secondary Channel -------------
> enabled enabled
> --------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------
> DMA enabled: no no yes no
> UDMA enabled: no no yes no
> UDMA enabled: X X 2 X
> UDMA
> DMA
> PIO
>
> cat /proc/ide/drivers
> ide-scsi version 0.92
> ide-cdrom version 4.61
> ide-disk version 1.18
>
> cat /proc/ide/hde/geometry
> physical 16383/16/63
> logical 65535/16/63
>
> cat /proc/ide/hdg/geometry
> physical 16383/16/63
> logical 65535/16/63
>
> hdparm -I /dev/hde
>
> /dev/hde:
>
> ATA device, with non-removable media
> Model Number: Maxtor 6Y120M0
> Serial Number: Y3MGJ4XE
> Firmware Revision: YAR51EW0
> Standards:
> Supported: 7 6 5 4
> Likely used: 7
> Configuration:
> Logical max current
> cylinders 16383 16383
> heads 16 16
> sectors/track 63 63
> --
> CHS current addressable sectors: 16514064
> LBA user addressable sectors: 240121728
> device size with M = 1024*1024: 117246 MBytes
> device size with M = 1000*1000: 122942 MBytes (122 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 0
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * NOP cmd
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Host Protected Area feature set
> * Look-ahead
> * Write cache
> * Power Management feature set
> Security Mode feature set
> * SMART feature set
> * FLUSH CACHE EXT command
> * Mandatory FLUSH CACHE command
> * Device Configuration Overlay feature set
> * Automatic Acoustic Management feature set
> SET MAX security extension
> Advanced Power Management feature set
> * DOWNLOAD MICROCODE cmd
> * SMART self-test
> * SMART error logging
> Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
> Checksum: correct
>
> hdparm -I /dev/hdg
>
> /dev/hdg:
>
> ATA device, with non-removable media
> Model Number: Maxtor 6Y120M0
> Serial Number: Y3MGJ86E
> Firmware Revision: YAR51EW0
> Standards:
> Supported: 7 6 5 4
> Likely used: 7
> Configuration:
> Logical max current
> cylinders 16383 16383
> heads 16 16
> sectors/track 63 63
> --
> CHS current addressable sectors: 16514064
> LBA user addressable sectors: 240121728
> device size with M = 1024*1024: 117246 MBytes
> device size with M = 1000*1000: 122942 MBytes (122 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 0
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * NOP cmd
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Host Protected Area feature set
> * Look-ahead
> * Write cache
> * Power Management feature set
> Security Mode feature set
> * SMART feature set
> * FLUSH CACHE EXT command
> * Mandatory FLUSH CACHE command
> * Device Configuration Overlay feature set
> * Automatic Acoustic Management feature set
> SET MAX security extension
> Advanced Power Management feature set
> * DOWNLOAD MICROCODE cmd
> * SMART self-test
> * SMART error logging
> Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
> Checksum: correct
>
> hdparm -i /dev/hde
>
> /dev/hde:
>
> Model=Maxtor 6Y120M0, FwRev=YAR51EW0, SerialNo=Y3MGJ4XE
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
> BuffType=DualPortCache, BuffSize=7936kB, MaxMultSect=16, MultSect=off
> CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=240121728
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 udma2
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: (null):
>
> * signifies the current active mode
>
> hdparm -i /dev/hdg
>
> /dev/hdg:
>
> Model=Maxtor 6Y120M0, FwRev=YAR51EW0, SerialNo=Y3MGJ86E
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
> BuffType=DualPortCache, BuffSize=7936kB, MaxMultSect=16, MultSect=off
> CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=240121728
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 udma2
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: (null):
>
> * signifies the current active mode
>
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ICH3: IDE controller at PCI slot 0000:00:1f.1
> ICH3: chipset revision 2
> ICH3: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x2060-0x2067, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x2068-0x206f, BIOS settings: hdc:pio, hdd:pio
> hdc: CD-224E, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> SiI3112 Serial ATA: IDE controller at PCI slot 0000:03:02.0
> SiI3112 Serial ATA: chipset revision 2
> SiI3112 Serial ATA: 100% native mode on irq 26
> ide2: MMIO-DMA , BIOS settings: hde:DMA, hdf:DMA
> ide3: MMIO-DMA , BIOS settings: hdg:DMA, hdh:DMA
> hde: Maxtor 6Y120M0, ATA DISK drive
> ide2 at 0xf8858080-0xf8858087,0xf885808a on irq 26
> hdg: Maxtor 6Y120M0, ATA DISK drive
> ide3 at 0xf88580c0-0xf88580c7,0xf88580ca on irq 26
> SiI3112 Serial ATA: IDE controller at PCI slot 0000:03:03.0
> SiI3112 Serial ATA: chipset revision 2
> SiI3112 Serial ATA: 100% native mode on irq 27
> ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio
> ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio
> hdi: no response (status = 0xfe)
> hdk: no response (status = 0xfe)
> hdi: no response (status = 0xfe), resetting drive
> hdi: no response (status = 0xfe)
> hdk: no response (status = 0xfe), resetting drive
> hdk: no response (status = 0xfe)
> hde: max request size: 64KiB
> hde: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63
> /dev/ide/host2/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 >
> hdg: max request size: 64KiB
> hdg: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63
> /dev/ide/host2/bus1/target0/lun0:
> hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
>
> Additionally, if I try to partition /dev/hdg (which has no partition
> table yet), using fdisk, it strangley doesn't ask me for much
> information, such as how large it should be:
>
> fdisk /dev/hdg
>
> The number of cylinders for this disk is set to 238216.
> There is nothing wrong with that, but this is larger than 1024,
> and could in certain setups cause problems with:
> 1) software that runs at boot time (e.g., old versions of LILO)
> 2) booting and partitioning software from other OSs
> (e.g., DOS FDISK, OS/2 FDISK)
>
> Command (m for help): p
>
> Disk /dev/hdg: 122.9 GB, 122942324736 bytes
> 16 heads, 63 sectors/track, 238216 cylinders
> Units = cylinders of 1008 * 512 = 516096 bytes
>
> Device Boot Start End Blocks Id System
>
> Command (m for help): a
> Partition number (1-4): 1
> Warning: partition 1 has empty type
>
> Command (m for help): p
>
> Disk /dev/hdg: 122.9 GB, 122942324736 bytes
> 16 heads, 63 sectors/track, 238216 cylinders
> Units = cylinders of 1008 * 512 = 516096 bytes
>
> Device Boot Start End Blocks Id System
> /dev/hdg1 * 1 1 0 0 Empty
> Partition 1 does not end on cylinder boundary.
>
> Command (m for help):
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Stephan Dreyer: "Get ip before accept"
- In reply to: micah milano: "SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Next in thread: Bartlomiej Zolnierkiewicz: "Re: SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Reply: Bartlomiej Zolnierkiewicz: "Re: SiI3112 Serial ATA Maxtor 6Y120M0 incorrect geometry detected"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
