Re: 2.4.29-pre1 OOPS early in boot with Intel ICH5 SATA controller
From: Alan J. Wylie (alan_at_wylie.me.uk)
Date: 12/13/04
- Previous message: Pavel Machek: "Re: [ACPI][2.6.10-rc3][SUSPEND] S3 mode - Cannot resume from PCI devices"
- In reply to: Jeff Garzik: "Re: 2.4.29-pre1 OOPS early in boot with Intel ICH5 SATA controller"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Mon, 13 Dec 2004 12:11:01 +0000 To: Jeff Garzik <jgarzik@pobox.com>
On Mon, 13 Dec 2004 06:09:26 -0500, Jeff Garzik <jgarzik@pobox.com> said:
> Is it possible for you to enable the following two #ifdefs in
> include/linux/libata.h, and send me the output?
> #define ATA_DEBUG /* debugging output */
> #define ATA_VERBOSE_DEBUG /* yet more debugging output */
(Hand transcribed - E&OE)
ksymoops output below.
...
piix_init: pci_module_init
ata_pci_init_one: ENTER
PCI: found IRQ 10 for device 00:1f.2
PCI: Sharing IRQ 10 with 00:1d.2
PCI: Sharing IRQ 10 with 04:02.0
piix_init: scsi_register_host
ata_scsi_detect: ENTER
ata_device_add: ENTER
ata_host_add: ENTER
ata_port_start: prd alloc, virt f7e5a000, dma 37e5a000
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18E0 irq 14
ata_device_add: probe begin
ata_device_add: ata1: probe begin
ata_bus_reset: ENTER, host 1, port 0
ata_bus_softreset: ata1: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 1, dev 0
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_dev_identify: do ATA identify
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_exec_command_pio: ata1: cmd 0xEC
ata_pio_sector: data read
ata_qc_complete: EXIT
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x0000
ata_dump_id: 80==0x00fe 81==0x001e 82==0x7c6b 83==0x7f09 84==0x4003
ata_dump_id: 88==0x207f 93==0x0000
ata1: dev 0 ATA, max UDMA/133, 39827088 sectors: lba48
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 1, dev 1) -- nodev
ata_host_set_pio: base 0x8 xfer_mode 0xc mask 0x1f x 4
ata_dev_set_xfermode: set features - xfer mode
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_tf_load_pio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_pio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_pio: device 0xA0
ata_command_exec_pio: ata1: cmd 0xEF
ata_host_intr: ata1: protocol 1 (dev_stat 0x50)
ata_qc_complete: EXIT
ata_dev_set_xfermode: EXIT
ata_dev_set_mode: idx=6 xfer_shift=0, xfer_mode=0x46, base=0x40, offset=6
ata1: dev 0 configured for UDMA/133
ata_device_add: ata1: probe end
ata_device_add: EXIT, returning 1
ata_device_add: ENTER
ata_host_add: ENTER
Unable to handle kernel NULL pointer dereference at virtual address 00000050
printing eip:
c01b028b
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c01b028b>] Not tainted
EFLAGS: 00010246
eax: 00000000 ebx: f7e6b878 ecx: 00000000 edx: 00000002
esi: f7e6b800 edi: f7e6ba20 ebp: f7e6ba20 esp: c19b7f10
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 1, stackpage=c19b7000)
Stack: f7e6b878 f7e6b800 c19bfa00 f7e6ba20 00000000 f7e6ba20 c19bfa00 00000000
c01b04c0 f7e6ba20 c19bfa00 00000000 c0209ae8 00000286 000003f6 000018e0
0000000e c19b0800 00000000 f7e6ba20 00000001 c0105000 c02282e0 c01b05d0
Call Trace: [<c01a04c0>] [<c0105000>] [<c01b05d0>] [<c01a0ab5>] [<c01161b1>]
[<c01b5efc>] [<c0105000>] [<c010507b>] [<c0105000>] [<c010569e>] [<c0105070>]
Code: ff 50 50 89 da 85 c0 75 12 8b 5c 24 14 89 d0 8b 74 24 18 8b
<0>Kernel panic: Attempted to kill init!
ksymoops 2.4.9 on i686 2.4.29-pre1-bk5. Options used
-V (default)
-K (specified)
-L (specified)
-O (specified)
-m /boot/System.map (specified)
Unable to handle kernel NULL pointer dereference at virtual address 00000050
c01b028b
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c01b028b>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010246
eax: 00000000 ebx: f7e6b878 ecx: 00000000 edx: 00000002
esi: f7e6b800 edi: f7e6ba20 ebp: f7e6ba20 esp: c19b7f10
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 1, stackpage=c19b7000)
Stack: f7e6b878 f7e6b800 c19bfa00 f7e6ba20 00000000 f7e6ba20 c19bfa00 00000000
c01b04c0 f7e6ba20 c19bfa00 00000000 c0209ae8 00000286 000003f6 000018e0
0000000e c19b0800 00000000 f7e6ba20 00000001 c0105000 c02282e0 c01b05d0
Call Trace: [<c01a04c0>] [<c0105000>] [<c01b05d0>] [<c01a0ab5>] [<c01161b1>]
[<c01b5efc>] [<c0105000>] [<c010507b>] [<c0105000>] [<c010569e>] [<c0105070>]
Code: ff 50 50 89 da 85 c0 75 12 8b 5c 24 14 89 d0 8b 74 24 18 8b
>>EIP; c01b028b <ata_host_add+6b/a0> <=====
Trace; c01a04c0 <proc_scsi_gen_write+160/470>
Trace; c0105000 <_stext+0/0>
Trace; c01b05d0 <ata_scsi_detect+70/90>
Trace; c01a0ab5 <scsi_register_host+2e5/2f0>
Trace; c01161b1 <printk+111/150>
Trace; c01b5efc <pci_register_driver+5c/60>
Trace; c0105000 <_stext+0/0>
Trace; c010507b <init+b/100>
Trace; c0105000 <_stext+0/0>
Trace; c010569e <arch_kernel_thread+2e/40>
Trace; c0105070 <init+0/100>
Code; c01b028b <ata_host_add+6b/a0>
00000000 <_EIP>:
Code; c01b028b <ata_host_add+6b/a0> <=====
0: ff 50 50 call *0x50(%eax) <=====
Code; c01b028e <ata_host_add+6e/a0>
3: 89 da mov %ebx,%edx
Code; c01b0290 <ata_host_add+70/a0>
5: 85 c0 test %eax,%eax
Code; c01b0292 <ata_host_add+72/a0>
7: 75 12 jne 1b <_EIP+0x1b>
Code; c01b0294 <ata_host_add+74/a0>
9: 8b 5c 24 14 mov 0x14(%esp),%ebx
Code; c01b0298 <ata_host_add+78/a0>
d: 89 d0 mov %edx,%eax
Code; c01b029a <ata_host_add+7a/a0>
f: 8b 74 24 18 mov 0x18(%esp),%esi
Code; c01b029e <ata_host_add+7e/a0>
13: 8b 00 mov (%eax),%eax
<0>Kernel panic: Attempted to kill init!
-- Alan J. Wylie http://www.wylie.me.uk/ "Perfection [in design] is achieved not when there is nothing left to add, but rather when there is nothing left to take away." -- Antoine de Saint-Exupery - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Pavel Machek: "Re: [ACPI][2.6.10-rc3][SUSPEND] S3 mode - Cannot resume from PCI devices"
- In reply to: Jeff Garzik: "Re: 2.4.29-pre1 OOPS early in boot with Intel ICH5 SATA controller"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
