CPUFREQ/speedstep on Intel 955X chipset based system

From: Michael Thonke (iogl64nx_at_gmail.com)
Date: 05/29/05

  • Next message: Pekka Enberg: "Re: [PROBLEM] Machine Freezes while Running Crossover Office" 
    Date:	Sun, 29 May 2005 20:20:31 +0200
To: linux mailing-list <linux-kernel@vger.kernel.org>

    Hello,

    I recently bought an Asus P5WAD2 motherboard which uses the Intel 955x
    chipset.
    I noticed that CPUFREQ/speedsteps with the same kernel and same config from
    my system with Intel 925XE and Intel Pentium 640 does not work on the
    system with
    Intel 955X chipset (the processor is the same). In Windows it works
    perfectly on 925XE
    and 955X chipset.

    The kernels I used

    2.6.12-rc5 vanilla with git4 patch
    2.6.12-rc5-mm1.

    I attached the output of dmesg and `cat /proc/cpuinfo`

    Thanks in advance

    Best regards
        Michael

    processor : 0
    vendor_id : GenuineIntel
    cpu family : 15
    model : 4
    model name : Intel(R) Pentium(R) 4 CPU 3.20GHz
    stepping : 3
    cpu MHz : 3211.542
    cache size : 2048 KB
    physical id : 0
    siblings : 2
    core id : 0
    cpu cores : 1
    fpu : yes
    fpu_exception : yes
    cpuid level : 5
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl est cid cx16 xtpr
    bogomips : 6340.60
    clflush size : 64
    cache_alignment : 128
    address sizes : 36 bits physical, 48 bits virtual
    power management:

    processor : 1
    vendor_id : GenuineIntel
    cpu family : 15
    model : 4
    model name : Intel(R) Pentium(R) 4 CPU 3.20GHz
    stepping : 3
    cpu MHz : 3211.542
    cache size : 2048 KB
    physical id : 0
    siblings : 2
    core id : 0
    cpu cores : 1
    fpu : yes
    fpu_exception : yes
    cpuid level : 5
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl est cid cx16 xtpr
    bogomips : 6406.14
    clflush size : 64
    cache_alignment : 128
    address sizes : 36 bits physical, 48 bits virtual
    power management:

    Bootdata ok (command line is root=/dev/md1 vga=794 quiet)
    Linux version 2.6.12-rc5-van-trunk (root@ioGL64NX_EMT64) (gcc-Version 3.4.3 20041125 (Gentoo 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #2 SMP Sun May 29 19:09:01 CEST 2005
    BIOS-provided physical RAM map:
     BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
     BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
     BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
     BIOS-e820: 0000000000100000 - 000000003ff80000 (usable)
     BIOS-e820: 000000003ff80000 - 000000003ff8e000 (ACPI data)
     BIOS-e820: 000000003ff8e000 - 000000003ffe0000 (ACPI NVS)
     BIOS-e820: 000000003ffe0000 - 0000000040000000 (reserved)
     BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
    ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fac40
    ACPI: XSDT (v001 A M I OEMXSDT 0x05000513 MSFT 0x00000097) @ 0x000000003ff80100
    ACPI: FADT (v003 A M I OEMFACP 0x05000513 MSFT 0x00000097) @ 0x000000003ff80290
    ACPI: MADT (v001 A M I OEMAPIC 0x05000513 MSFT 0x00000097) @ 0x000000003ff80390
    ACPI: OEMB (v001 A M I AMI_OEM 0x05000513 MSFT 0x00000097) @ 0x000000003ff8e040
    >>> ERROR: Invalid checksum
    ACPI: MCFG (v001 A M I OEMMCFG 0x05000513 MSFT 0x00000097) @ 0x000000003ff88760
    ACPI: DSDT (v001 A0229 A0229000 0x00000000 INTL 0x02002026) @ 0x0000000000000000
    On node 0 totalpages: 262016
      DMA zone: 4096 pages, LIFO batch:1
      Normal zone: 257920 pages, LIFO batch:31
      HighMem zone: 0 pages, LIFO batch:1
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 15:4 APIC version 16
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1 15:4 APIC version 16
    ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
    ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Setting APIC routing to flat
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 40000000 (gap: 40000000:bfb00000)
    Built 1 zonelists
    Kernel command line: root=/dev/md1 vga=794 quiet
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 131072 bytes)
    time.c: Using 3.579545 MHz PM timer.
    time.c: Detected 3211.542 MHz processor.
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    Memory: 1025492k/1048064k available (2770k kernel code, 22132k reserved, 1172k data, 220k init)
    Calibrating delay loop... 6340.60 BogoMIPS (lpj=3170304)
    Mount-cache hash table entries: 256
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    using mwait in idle threads.
    CPU: Physical Processor ID: 0
    CPU0: Thermal monitoring enabled (TM1)
    Using local APIC timer interrupts.
    Detected 12.545 MHz APIC timer.
    Booting processor 1/1 rip 6000 rsp ffff81000218ff58
    Initializing CPU#1
    Calibrating delay loop... 6406.14 BogoMIPS (lpj=3203072)
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU1: Thermal monitoring enabled (TM1)
                  Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 03
    APIC error on CPU1: 00(40)
    CPU 1: Syncing TSC to CPU 0.
    CPU 1: synchronized TSC with CPU 0 (last diff 37 cycles, maxerr 864 cycles)
    Brought up 2 CPUs
    time.c: Using PIT/TSC based timekeeping.
    testing NMI watchdog ... OK.
    CPU0 attaching sched-domain:
     domain 0: span 3
      groups: 1 2
      domain 1: span 3
       groups: 3
    CPU1 attaching sched-domain:
     domain 0: span 3
      groups: 2 1
      domain 1: span 3
       groups: 3
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    PCI: Using MMCONFIG at e0000000
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20050309
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    Boot video device is 0000:04:00.0
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 10 11 12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 13 devices
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    pnp: 00:06: ioport range 0x290-0x297 has been reserved
    IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
    Initializing Cryptographic API
    ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie03]
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    Allocate Port Service[pcie03]
    ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1c.4 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    Allocate Port Service[pcie03]
    vesafb: framebuffer at 0xd8000000, mapped to 0xffffc20010100000, using 5120k, total 131072k
    vesafb: mode is 1280x1024x16, linelength=2560, pages=1
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    fb1: Virtual frame buffer device, using 1024K of video memory
    ACPI: Processor [CPU1] (supports 8 throttling states)
    Real Time Clock Driver v1.12
    i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
    i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
    Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
    Hangcheck: Using monotonic_clock().
    PNP: No PS/2 controller found. Probing ports directly.
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    io scheduler noop registered
    io scheduler cfq registered
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 2 RAM disks of 2048K size 1024 blocksize
    loop: loaded (max 8 devices)
    ub: sizeof ub_scsi_cmd 88 ub_dev 2680
    usbcore: registered new driver ub
    Intel(R) PRO/1000 Network Driver - version 6.0.54-k2-NAPI
    Copyright (c) 1999-2004 Intel Corporation.
    ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
    ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 21 (level, low) -> IRQ 209
    sk98lin: Network Device Driver v8.18.2.2 (beta)
    (C)Copyright 1999-2005 Marvell(R).
    ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 21 (level, low) -> IRQ 209
    eth1: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
          PrefPort:A RlmtMode:Check Link State
    netconsole: not configured, aborting
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH7: IDE controller at PCI slot 0000:00:1f.1
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 217
    ICH7: chipset revision 1
    ICH7: not 100% native mode: will probe irqs later
        ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    Probing IDE interface ide0...
    hda: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    libata version 1.10 loaded.
    ahci version 1.00
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 225
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ahci(0000:00:1f.2) AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    ahci(0000:00:1f.2) flags: 64bit ncq pm led clo pio slum part
    ata1: SATA max UDMA/133 cmd 0xFFFFC2000000ED00 ctl 0x0 bmdma 0x0 irq 225
    ata2: SATA max UDMA/133 cmd 0xFFFFC2000000ED80 ctl 0x0 bmdma 0x0 irq 225
    ata3: SATA max UDMA/133 cmd 0xFFFFC2000000EE00 ctl 0x0 bmdma 0x0 irq 225
    ata4: SATA max UDMA/133 cmd 0xFFFFC2000000EE80 ctl 0x0 bmdma 0x0 irq 225
    ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata1: dev 0 ATA, max UDMA7, 312581808 sectors: lba48 ncq
    ata1: dev 0 configured for UDMA/133
    scsi0 : ahci
    ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata2: dev 0 ATA, max UDMA7, 312581808 sectors: lba48 ncq
    ata2: dev 0 configured for UDMA/133
    scsi1 : ahci
    ata3: no device found (phy stat 00000000)
    scsi2 : ahci
    ata4: no device found (phy stat 00000000)
    scsi3 : ahci
      Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
      Type: Direct-Access ANSI SCSI revision: 05
      Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
      Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
     sda: sda1 sda2 < sda5 >
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
     sdb: sdb1 sdb2 < sdb5 sdb6 >
    Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    usbmon: debugs is not available
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 233
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: Intel Corporation I/O Controller Hub EHCI USB
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 233, io mem 0xd2cff800
    PCI: cache line size of 128 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    USB Universal Host Controller Interface driver v2.2
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 233
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: Intel Corporation I/O Controller Hub UHCI USB #1
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 233, io base 0x00008000
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 50
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: Intel Corporation I/O Controller Hub UHCI USB #2
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 50, io base 0x00008400
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 58
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: Intel Corporation I/O Controller Hub UHCI USB #3
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 58, io base 0x00008800
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 66
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: Intel Corporation I/O Controller Hub UHCI USB #4
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 66, io base 0x00009000
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usb 2-1: new low speed USB device using uhci_hcd and address 2
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-2
    input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.01:USB HID core driver
    mice: PS/2 mouse device common for all mice
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: multipath personality registered as nr 7
    md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
    Advanced Linux Sound Architecture Driver Version 1.0.9.
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 66
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    ALSA device list:
      #0: HDA Intel at 0xd2cf8000 irq 66
    NET: Registered protocol family 2
    IP: routing cache hash table of 4096 buckets, 64Kbytes
    TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    ACPI wakeup devices:
    P0P1 P0P3 P0P4 P0P5 P0P6 P0P7 P0P8 P0P9 USB2 USB3 USB4 MC97 USB1 EUSB
    ACPI: (supports S0 S1 S3 S4 S5)
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdb5 ...
    md: adding sdb5 ...
    md: adding sda5 ...
    md: created md1
    md: bind<sda5>
    md: bind<sdb5>
    md: running: <sdb5><sda5>
    md1: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb5
    raid0: comparing sdb5(20000768) with sdb5(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda5
    raid0: comparing sda5(20000768) with sdb5(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 8 bytes for hash.
    md: ... autorun DONE.
    ReiserFS: md1: found reiserfs format "3.6" with standard journal
    cfq: depth 4 reached, tagging now on
    ReiserFS: md1: using ordered data mode
    ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: md1: checking transaction log (md1)
    ReiserFS: md1: Using r5 hash to sort names
    VFS: Mounted root (reiserfs filesystem) readonly.
    Freeing unused kernel memory: 220k freed
    cfq: depth 4 reached, tagging now on
    ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
    ReiserFS: sdb1: using ordered data mode
    ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sdb1: checking transaction log (sdb1)
    ReiserFS: sdb1: Using r5 hash to sort names
    e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
    nvidia: module license 'NVIDIA' taints kernel.
    ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:04:00.0 to 64
    NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:45:40 PST 2005

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  • Next message: Pekka Enberg: "Re: [PROBLEM] Machine Freezes while Running Crossover Office"

    Relevant Pages