Orinoco_plx woes on 2.6.13
From: Nathan Mahon (lkml.org_at_vaevictus.net)
Date: 07/14/05
- Previous message: Al Boldi: "RE: [PATCH] i386: Selectable Frequency of the Timer Interrupt"
- Next in thread: Nathan Mahon: "Re: Orinoco_plx woes on 2.6.13"
- Reply: Nathan Mahon: "Re: Orinoco_plx woes on 2.6.13"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Thu, 14 Jul 2005 13:52:55 -0400 To: linux-kernel@vger.kernel.org
I use a Belkin F5D6020 wifi card, (version one), and a belkin f5d6000 pci adapter for it. A while ago, it was working flawlessly, though I
didn't use it that much after the wife's laptop died.
I've rolled through some kernel upgrades... and it appears my wifi does not work anymore.
here's the technical stuff:
I was still using 2.4 when it was working for sure, but I can't verify that it wasn't ever working on 2.6.
under 2.6.11, i noticed the problem, I couldn't bring the interface up.
dmesg produced similar results (to 2.6.13 i have now), but iirc, the
iwconfig didn't make it look like the card was working at all. I rolled
to 2.6.13, and things improved only slightly.
Now, with 2.6.13, I get a successful modprobe orinoco_plx:
>> auron root # dmesg
>> orinoco_plx 0.15rc2 (Pavel Roskin <proski@gnu.org>, David Gibson
>> <hermes@gibson.dropbear.id.au>, Daniel Barlow <dan@telent.net>)
>> PCI: Found IRQ 9 for device 0000:00:0a.0
>> orinoco_plx: Detected Orinoco/Prism2 PLX device at 0000:00:0a.0 irq:9,
>> io addr:0x2c00
>> orinoco_plx: CIS: 01:03:00:00:FF:17:04:67:5A:08:FF:1D:05:01:67:5A:
>> eth2: Hardware identity 8002:0000:0001:0000
>> eth2: Station identity 001f:0003:0000:0008
>> eth2: Firmware determined as Intersil 0.8.3
>> eth2: Ad-hoc demo mode supported
>> eth2: IEEE standard IBSS ad-hoc mode supported
>> eth2: WEP supported, 104-bit key
>> eth2: MAC address 00:30:BD:63:21:11
>> eth2: Station name "Prism I"
>> eth2: ready
>
>
and at this point, iwconfig looks like the card is behaving somewhat:
>> auron root # iwconfig eth2
>> eth2 IEEE 802.11b ESSID:"" Nickname:"Prism I"
>> Mode:Managed Frequency:2.462 GHz Access Point:
>> 00:00:00:00:00:00
>> Bit Rate:11 Mb/s Sensitivity:1/3
>> Retry min limit:8 RTS thr:off Fragment thr:off
>> Encryption key:off
>> Power Management:off
>> Link Quality=0/92 Signal level=134/153 Noise level=134/153
>> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
>> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>
>
dmesg hasn't changed at this point.
however, ifconfig breaks it:
auron root # ifconfig eth2 10.5.6.1 netmask 255.255.255.0 broadcast
10.5.6.255
>> SIOCSIFFLAGS: No such device
>
>
and dmesg now says this:
>> hermes @ 00012c00: Card removed while waiting for command 0x0f38
>> completion.
>> eth2: Error -19 configuring card
>
>
and if i retry the ifconfig, i get a different error and a different
dmesg result:
>> SIOCSIFFLAGS: Connection timed out
>
>
>> eth2: Error -110 setting MAC address
>> eth2: Error -110 configuring card
>
>
Just to state the implied, I'm *not* removing the card, and rmmod'ing the orinico_plx driver and re-modprobing it will produce consistantly the same errors.
Thanks,
Nathan Mahon
System: old amd k6-2 333mhz box with 256mb ram
Distro: gentoo
Kernel config: http://www.vaevictus.net/2.6.13_config.txt
First Post: so flame me if necessary. :D
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Al Boldi: "RE: [PATCH] i386: Selectable Frequency of the Timer Interrupt"
- Next in thread: Nathan Mahon: "Re: Orinoco_plx woes on 2.6.13"
- Reply: Nathan Mahon: "Re: Orinoco_plx woes on 2.6.13"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
