Re: 2.6.13-rc3-mm3
From: Andrew Morton (akpm_at_osdl.org)
Date: 07/29/05
- Previous message: Eric W. Biederman: "[PATCH] i386 io_apic.c: Memorize at bootup where the i8259 is connected"
- In reply to: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Next in thread: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Reply: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Fri, 29 Jul 2005 12:33:30 -0700 To: Michael Thonke <tk-shockwave@web.de>
Michael Thonke <tk-shockwave@web.de> wrote:
>
> Andrew Morton schrieb:
> > Michael Thonke <iogl64nx@gmail.com> wrote:
> >> here again I have two problems. With 2.6.13-rc3-mm3 I have problems
> >> using my SATA drives on Intel ICH6.
> >> The kernel can't route there IRQs or can't discover them. the option
> >> irqpoll got them to work now.
> >> The problem is new because 2.6.13-rc3[-mm1,mm2] work without any problems.
> >
> > OK. Please generate the full dmesg output for -mm2 and for -mm3 and run
> > `diff -u dmesg.mm2 dmesg.mm3' and send it? And keep those files because we
> > may end up needing to add them to an acpi bugzilla entry ;)
>
> Well I did a little mistake..it only worked correctly up to
> 2.6.13-rc3-mm1 but this dmesg output I have.
>
> Well as I save mm[2,3] are unable to setup the correct IRQs for the
> devices..and please note that 2.6.13-rc3-mm3 only booted with irqpoll so
> its in the dmesg output "dmesg.mm3"
> Normaly the IRQ routed to something about 1xx now they are 1-21?! Caused
> by irqpoll?
>
Are these problems only present in -mm kernels? Does 2.6.13-rc4 work OK?
> > Odd trace. Do you have CONFIG_KALLSYMS enabled? If not, please turn it on.
>
> Mh I tried but my system freezes on boot then. And screen leaves blank.
> >
Oh geeze.
@@ -53,10 +23,18 @@
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
+ ACPI-0287: *** Error: Region SystemMemory(0) has no handler
+ ACPI-0127: *** Error: acpi_load_tables: Could not load namespace: AE_NOT_EXIST
+ ACPI-0136: *** Error: acpi_load_tables: Could not load tables: AE_NOT_EXIST
+ACPI: Unable to load the System Description Tables
ENABLING IO-APIC IRQs
-..TIMER: vector=0x31 pin1=2 pin2=0
+..TIMER: vector=0x31 pin1=2 pin2=-1
NET: Registered protocol family 16
PCI: Using configuration type 1
+ACPI: Subsystem revision 20050708
+ACPI: Interpreter disabled.
Well it looks like ACPI committed suicide, so there's probably not much
point looking at the other things until that gets addressed.
Would you have time to raise a kernel bugzilla entry for this? Raise it
against the ACPI AML interpreter, version 20050708 and mention the above
failure. The output of acpidump (from
ftp://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/utils/pmtools-20050727.tar.gz)
will probably be asked for.
Thanks.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Eric W. Biederman: "[PATCH] i386 io_apic.c: Memorize at bootup where the i8259 is connected"
- In reply to: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Next in thread: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Reply: Michael Thonke: "Re: 2.6.13-rc3-mm3"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
