Re: 2 errors in 2.6.12
From: Michael Krufky (mkrufky_at_m1k.net)
Date: 08/01/05
- Previous message: Lee Revell: "Re: Power consumption HZ100, HZ250, HZ1000: new numbers"
- In reply to: hermann pitton: "Re: 2 errors in 2.6.12"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Mon, 01 Aug 2005 16:02:07 -0400 To: hermann pitton <hermann.pitton@onlinehome.de>
Thank you, Hermann.
AKPM (cc re-added) requested that this thread retain cc's to him... so
he should see that it has been resolved.......
hermann pitton wrote:
>Hello,
>
>this one is solved.
>
>Guess we will see similar issues more often for a while.
>
>Cheers,
>Hermann
>
>
>Am Montag, den 01.08.2005, 20:11 +0200 schrieb CIJOML:
>
>
>>On Mon, 1 Aug 2005, hermann pitton wrote:
>>
>>
>>
>>>Am Montag, den 01.08.2005, 11:16 +0200 schrieb CIJOML:
>>>
>>>
>>>>Hi,
>>>>
>>>>my card is impossible to be autodetected. Valid sections for it's
>>>>identification are missing.
>>>>
>>>>I asked for this some time ago. I need to use insmod option.
>>>>
>>>>Michal
>>>>
>>>>
>>>Hi Michal,
>>>
>>>the "tuner type=N" insmod option is gone away.
>>>
>>>There has been a warning that it is deprecated for about 1 1/2 years
>>>in dmesg. Please remove it from /etc/modprobe.conf or where else it is
>>>called and replace it with "options bttv card=N tuner=N", guess you
>>>
>>>
>>AAAAH!!!! This helped!!! Thanks a lot
>>after options bttv card=42 radio=1 tuner=1
>>card works! :)
>>
>>Linux video capture interface: v1.00
>>bttv: driver version 0.9.15 loaded
>>bttv: using 8 buffers with 2080k (520 pages) each for capture
>>bttv: Bt8xx card found (0).
>>ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low)
>>-> IRQ 9
>>bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio:
>>0xb69fe000
>>bttv0: using: ProVideo PV951 [card=42,insmod option]
>>bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>>bttv0: using tuner=1
>>bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>>bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>>tvaudio: TV audio decoder + audio/video mux driver
>>tvaudio: known chips:
>>tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
>>(PV951),ta8874z
>>tvaudio: found pic16c54 (PV951) @ 0x96
>>bttv0: i2c: checking for TDA9887 @ 0x86... not found
>> : chip found @ 0xc0 (bt878 #0 [sw])
>> : All bytes are equal. It is not a TEA5767
>>tuner 0-0060: type set to 1 (Philips PAL_I (FI1246 and compatibles))
>>bttv0: registered device video0
>>bttv0: registered device vbi0
>>bttv0: registered device radio0
>>bttv0: PLL: 28636363 => 35468950 .. ok
>>
>>Thanks a lot!
>>
>>Michal
>>
>>
>>
>>
>>>might use tuner=5, and what else you might need and then "depmod -a".
>>>Does this help?
>>>
>>>Greetings,
>>>Hermann
>>>
>>>
>>>
>>>
>>>>On Sun, 31 Jul 2005, Michael Krufky wrote:
>>>>
>>>>
>>>>
>>>>>Andrew Morton wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Michal Semler <cijoml@volny.cz> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>This is what I gets into dmesg:
>>>>>>>
>>>>>>>Linux video capture interface: v1.00
>>>>>>>bttv: driver version 0.9.15 loaded
>>>>>>>bttv: using 8 buffers with 2080k (520 pages) each for capture
>>>>>>>bttv: Bt8xx card found (0).
>>>>>>>ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) ->
>>>>>>>IRQ 9
>>>>>>>bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
>>>>>>>bttv0: using: ProVideo PV951 [card=42,insmod option]
>>>>>>>bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>>>>>>>bttv0: using tuner=1
>>>>>>>bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>>>>>>>bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>>>>>>>tvaudio: TV audio decoder + audio/video mux driver
>>>>>>>tvaudio: known chips:
>>>>>>>tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
>>>>>>>(PV951),ta8874z
>>>>>>>tvaudio: found pic16c54 (PV951) @ 0x96
>>>>>>>bttv0: i2c: checking for TDA9887 @ 0x86... not found
>>>>>>>tuner: Unknown parameter `type'
>>>>>>>
>>>>>>>
>>> ^^^^^^^^^^^^^^^^^^^^^^^^
>>>
>>>
>[...]
>
>
>
-- Michael Krufky - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
- Previous message: Lee Revell: "Re: Power consumption HZ100, HZ250, HZ1000: new numbers"
- In reply to: hermann pitton: "Re: 2 errors in 2.6.12"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]