Re: Second "CPU" of 1-core HyperThreading CPU not found in 2.6.13

From: Chase Venters (chase.venters_at_clientec.com)
Date: 08/31/05

  • Next message: Daniel Phillips: "[RFC][PATCH 2 of 4] Configfs is really sysfs" 
    To: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Date:	Tue, 30 Aug 2005 17:56:49 -0500

    > Complete 'dmesg' please.

    See below.

    Thanks,
    Chase

    Linux version 2.6.13 (root@turbotaz) (gcc version 3.3.5-20050130 (Gentoo Linux
    3.3.5.20050130-r1, ssp-3.3.5.20050130-1, pie-8.7.7.1)) #2 SMP Sun Aug 28
    23:54:34 CDT 2005
    BIOS-provided physical RAM map:
     BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
     BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
     BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
     BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
     BIOS-e820: 000000003ffb0000 - 000000003ffbe000 (ACPI data)
     BIOS-e820: 000000003ffbe000 - 000000003fff0000 (ACPI NVS)
     BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
     BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
    Warning only 896MB will be used.
    Use a HIGHMEM enabled kernel.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    On node 0 totalpages: 229376
      DMA zone: 4096 pages, LIFO batch:1
      Normal zone: 225280 pages, LIFO batch:31
      HighMem zone: 0 pages, LIFO batch:1
    DMI 2.3 present.
    ACPI: RSDP (v000 ACPIAM ) @ 0x000fb250
    ACPI: RSDT (v001 A M I OEMRSDT 0x11000429 MSFT 0x00000097) @ 0x3ffb0000
    ACPI: FADT (v001 A M I OEMFACP 0x11000429 MSFT 0x00000097) @ 0x3ffb0200
    ACPI: OEMB (v001 A M I AMI_OEM 0x11000429 MSFT 0x00000097) @ 0x3ffbe040
    ACPI: MCFG (v001 A M I OEMMCFG 0x11000429 MSFT 0x00000097) @ 0x3ffb6c70
    ACPI: DSDT (v001 A0077 A0077001 0x00000001 INTL 0x02002026) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x808
    Intel MultiProcessor Specification v1.4
        Virtual Wire compatibility mode.
    OEM ID: INTEL Product ID: DELUXE APIC at: 0xFEE00000
    Processor #0 15:4 APIC version 20
    I/O APIC #2 Version 32 at 0xFEC00000.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Processors: 1
    Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
    Built 1 zonelists
    Kernel command line: root=/dev/md1 noapic
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Detected 3212.948 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 902076k/917504k available (4249k kernel code, 14984k reserved, 1657k
    data, 268k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 6427.67 BogoMIPS
    (lpj=3213838)
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
    0000441d 00000000 00000000
    CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d
    00000000 00000000
    monitor/mwait feature present.
    using mwait in idle threads.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 1024K
    CPU: Physical Processor ID: 0
    CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000441d
    00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
    CPU0: Thermal monitoring enabled
    mtrr: v2.0 (20020519)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ACPI: setting ELCR to 0200 (from 0cb8)
    CPU0: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 01
    Total of 1 processors activated (6427.67 BogoMIPS).
    Brought up 1 CPUs
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=4
    PCI: Using MMCONFIG
    ACPI: Subsystem revision 20050408
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    Boot video device is 0000:04:00.0
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 14 devices
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    PCI: Bridge: 0000:00:01.0
      IO window: e000-efff
      MEM window: cdf00000-cfffffff
      PREFETCH window: d0000000-dfffffff
    PCI: Bridge: 0000:00:1c.0
      IO window: d000-dfff
      MEM window: disabled.
      PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1c.1
      IO window: c000-cfff
      MEM window: cde00000-cdefffff
      PREFETCH window: 40000000-400fffff
    PCI: Bridge: 0000:00:1e.0
      IO window: b000-bfff
      MEM window: cdc00000-cddfffff
      PREFETCH window: 40100000-401fffff
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
    PCI: setting IRQ 4 as level-triggered
    ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    pnp: 00:06: ioport range 0x290-0x297 has been reserved
    Machine check exception polling timer started.
    IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
    audit: initializing netlink socket (disabled)
    audit(1125294657.731:1): initialized
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    Initializing Cryptographic API
    ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie03]
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    Allocate Port Service[pcie03]
    ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    Allocate Port Service[pcie03]
    ACPI: Power Button (FF) [PWRF]
    ACPI: Power Button (CM) [PWRB]
    ACPI: CPU0 (power states: C1[C1])
    ACPI: Processor [CPU1] (supports 8 throttling states)
    Real Time Clock Driver v1.12
    Non-volatile memory driver v1.2
    hw_random: RNG not detected
    [drm] Initialized drm 1.0.0 20040925
    PNP: No PS/2 controller found. Probing ports directly.
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
    ub: sizeof ub_scsi_cmd 68 ub_dev 2412 ub_lun 140
    usbcore: registered new driver ub
    Linux video capture interface: v1.00
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH6: IDE controller at PCI slot 0000:00:1f.1
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
    PCI: setting IRQ 5 as level-triggered
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 5 (level, low) ->
    IRQ 5
    ICH6: chipset revision 3
    ICH6: not 100% native mode: will probe irqs later
        ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
        ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    IT8212: IDE controller at PCI slot 0000:01:04.0
    ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKH] -> GSI 11 (level, low) ->
    IRQ 11
    IT8212: chipset revision 19
    it821x: controller in pass through mode.
    IT8212: 100% native mode on irq 11
        ide2: BM-DMA at 0xb000-0xb007, BIOS settings: hde:pio, hdf:pio
        ide3: BM-DMA at 0xb008-0xb00f, BIOS settings: hdg:pio, hdh:pio
    Probing IDE interface ide2...
    Probing IDE interface ide3...
    Probing IDE interface ide1...
    Probing IDE interface ide2...
    Probing IDE interface ide3...
    hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(66)
    Uniform CD-ROM driver Revision: 3.20
    ide-floppy driver 0.99.newide
    ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7
    PCI: setting IRQ 7 as level-triggered
    ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNKF] -> GSI 7 (level, low) ->
    IRQ 7
    scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
            <Adaptec 2902/04/10/15/20C/30C SCSI adapter>
            aic7850: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs

      Vendor: PLEXTOR Model: CD-R PX-W124TS Rev: 1.07
      Type: CD-ROM ANSI SCSI revision: 02
     target0:0:4: asynchronous.
     target0:0:4: Beginning Domain Validation
     target0:0:4: Domain Validation skipping write tests
     target0:0:4: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 8)
     target0:0:4: Ending Domain Validation
    libata version 1.12 loaded.
    ahci version 1.01
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 3
    PCI: setting IRQ 3 as level-triggered
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 3 (level, low) ->
    IRQ 3
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ahci(0000:00:1f.2) AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode
    ahci(0000:00:1f.2) flags: 64bit ncq pm led slum part
    ata1: SATA max UDMA/133 cmd 0xF881ED00 ctl 0x0 bmdma 0x0 irq 3
    ata2: SATA max UDMA/133 cmd 0xF881ED80 ctl 0x0 bmdma 0x0 irq 3
    ata3: SATA max UDMA/133 cmd 0xF881EE00 ctl 0x0 bmdma 0x0 irq 3
    ata4: SATA max UDMA/133 cmd 0xF881EE80 ctl 0x0 bmdma 0x0 irq 3
    ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003
    88:203f
    ata1: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
    ata1: dev 0 configured for UDMA/100
    scsi1 : ahci
    ata2: dev 0 cfg 49:2f00 82:306b 83:7e01 84:4003 85:3069 86:3c01 87:4003
    88:203f
    ata2: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
    ata2: dev 0 configured for UDMA/100
    scsi2 : ahci
    ata3: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003
    88:203f
    ata3: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
    ata3: dev 0 configured for UDMA/100
    scsi3 : ahci
    ata4: dev 0 cfg 49:2f00 82:306b 83:7e01 84:4003 85:3069 86:3c01 87:4003
    88:203f
    ata4: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
    ata4: dev 0 configured for UDMA/100
    scsi4 : ahci
      Vendor: ATA Model: WDC WD3200JD-00K Rev: 08.0
      Type: Direct-Access ANSI SCSI revision: 05
      Vendor: ATA Model: WDC WD3200JD-60K Rev: 08.0
      Type: Direct-Access ANSI SCSI revision: 05
      Vendor: ATA Model: WDC WD3200JD-00K Rev: 08.0
      Type: Direct-Access ANSI SCSI revision: 05
      Vendor: ATA Model: WDC WD3200JD-60K Rev: 08.0
      Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sda: drive cache: write back
    SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sda: drive cache: write back
     sda: sda1 sda2 sda3
    Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
    SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdb: drive cache: write back
     sdb: sdb1 sdb2 sdb3
    Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
    SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdc: drive cache: write back
    SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdc: drive cache: write back
     sdc: sdc1 sdc2 sdc3
    Attached scsi disk sdc at scsi3, channel 0, id 0, lun 0
    SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdd: drive cache: write back
    SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
    SCSI device sdd: drive cache: write back
     sdd: sdd1 sdd2 sdd3
    Attached scsi disk sdd at scsi4, channel 0, id 0, lun 0
    sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
    Attached scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 4, lun 0, type 5
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg4 at scsi4, channel 0, id 0, lun 0, type 0
    usbmon: debugfs is not available
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 11 (level, low) ->
    IRQ 11
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
    USB2 EHCI Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 11, io mem 0xcdbff800
    PCI: cache line size of 128 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    USB Universal Host Controller Interface driver v2.3
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 11 (level, low) ->
    IRQ 11
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
    USB UHCI #1
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 11, io base 0x00009880
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 3 (level, low) ->
    IRQ 3
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
    USB UHCI #2
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 3, io base 0x00009c00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) ->
    IRQ 5
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
    USB UHCI #3
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000a000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
    USB UHCI #4
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000a080
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usb 1-1: new high speed USB device using ehci_hcd and address 2
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    usb 1-6: new high speed USB device using ehci_hcd and address 6
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    usb 3-1: new low speed USB device using uhci_hcd and address 2
    usb 3-2: new full speed USB device using uhci_hcd and address 3
    usbcore: registered new driver hiddev
    usb 4-1: new low speed USB device using uhci_hcd and address 2
    input: USB HID v1.10 Keyboard [Key Tronic Keytronic USB Keyboard] on
    usb-0000:00:1d.1-1
    hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS BR 800
    FW:9.o2 .D USB FW:o2] on usb-0000:00:1d.2-1
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.01:USB HID core driver
    mice: PS/2 mouse device common for all mice
    input: PC Speaker
    I2O subsystem v1.288
    i2o: max drivers = 8
    I2O Configuration OSM v1.248
    I2O Bus Adapter OSM v$Rev$
    I2O Block Device OSM v1.287
    I2O SCSI Peripheral OSM v1.282
    I2O ProcFS OSM v1.145
    i2c /dev entries driver
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: raid1 personality registered as nr 3
    md: raid10 personality registered as nr 9
    md: raid5 personality registered as nr 4
    raid5: automatically using best checksumming function: pIII_sse
       pIII_sse : 5040.000 MB/sec
    raid5: using function: pIII_sse (5040.000 MB/sec)
    raid6: int32x1 906 MB/s
    raid6: int32x2 976 MB/s
    raid6: int32x4 781 MB/s
    raid6: int32x8 605 MB/s
    usb 1-1.1: new low speed USB device using ehci_hcd and address 7
    raid6: mmxx1 1945 MB/s
    raid6: mmxx2 2246 MB/s
    raid6: sse1x1 1125 MB/s
    raid6: sse1x2 1277 MB/s
    raid6: sse2x1 2238 MB/s
    raid6: sse2x2 2390 MB/s
    raid6: using algorithm sse2x2 (2390 MB/s)
    md: raid6 personality registered as nr 8
    md: multipath personality registered as nr 7
    md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 3.38
    device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
    device-mapper: dm-multipath version 1.0.4 loaded
    device-mapper: dm-round-robin version 1.0.0 loaded
    device-mapper: dm-emc version 0.0.3 loaded
    padlock: VIA PadLock not detected.
    oprofile: using NMI interrupt.
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
    TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    IPv4 over IPv4 tunneling driver
    GRE over IPv4 tunneling driver
    ip_conntrack version 2.1 (7168 buckets, 57344 max) - 248 bytes per conntrack
    usb 1-1.2: new low speed USB device using ehci_hcd and address 8
    input: USB HID v1.00 Mouse [USB Mouse] on usb-0000:00:1d.7-1.2
    ip_tables: (C) 2000-2002 Netfilter core team
    ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.
    http://snowman.net/projects/ipt_recent/
    ClusterIP Version 0.7 loaded successfully
    arp_tables: (C) 2002 David S. Miller
    TCP bic registered
    Initializing IPsec netlink socket
    NET: Registered protocol family 1
    NET: Registered protocol family 10
    Disabled Privacy Extensions on device c0652bc0(lo)
    IPv6 over IPv4 tunneling driver
    ip6_tables: (C) 2000-2002 Netfilter core team
    registering ipv6 mark target
    NET: Registered protocol family 17
    NET: Registered protocol family 15
    Bridge firewalling registered
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    Using IPI Shortcut mode
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdd3 ...
    md: adding sdd3 ...
    md: sdd1 has different UUID to sdd3
    md: adding sdc3 ...
    md: sdc1 has different UUID to sdd3
    md: adding sdb3 ...
    md: sdb1 has different UUID to sdd3
    md: adding sda3 ...
    md: sda1 has different UUID to sdd3
    md: created md1
    md: bind<sda3>
    md: bind<sdb3>
    md: bind<sdc3>
    md: bind<sdd3>
    md: running: <sdd3><sdc3><sdb3><sda3>
    raid10: raid set md1 active with 4 out of 4 devices
    md: considering sdd1 ...
    md: adding sdd1 ...
    md: adding sdc1 ...
    md: adding sdb1 ...
    md: adding sda1 ...
    md: created md0
    md: bind<sda1>
    md: bind<sdb1>
    md: bind<sdc1>
    md: bind<sdd1>
    md: running: <sdd1><sdc1><sdb1><sda1>
    raid1: raid set md0 active with 4 out of 4 mirrors
    md: ... autorun DONE.
    ReiserFS: md1: found reiserfs format "3.6" with standard journal
    ReiserFS: md1: using ordered data mode
    ReiserFS: md1: journal params: device md1, size 8192, journal first block 18,
    max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: md1: checking transaction log (md1)
    ReiserFS: md1: Using r5 hash to sort names
    VFS: Mounted root (reiserfs filesystem) readonly.
    Freeing unused kernel memory: 268k freed
    Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1
    Adding 1004052k swap on /dev/sdb2. Priority:-2 extents:1
    Adding 1004052k swap on /dev/sdc2. Priority:-3 extents:1
    Adding 1004052k swap on /dev/sdd2. Priority:-4 extents:1
    nvidia: module license 'NVIDIA' taints kernel.
    ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:04:00.0 to 64
    NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7667 Fri Jun 17
    07:01:04 PDT 2005
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
    IRQ 10
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    eth0: register usbnet at usb-0000:00:1d.7-6, Netgear FA-120 USB Ethernet,
    00:09:5b:e0:77:33
    usbcore: registered new driver usbnet
    eth0: no IPv6 routers present
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth1: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
          PrefPort:A RlmtMode:Check Link State
    usb 1-1.1: USB disconnect, address 7
    usb 1-1.1: new low speed USB device using ehci_hcd and address 9
    eth1: network connection up using port A
        speed: 100
        autonegotiation: yes
        duplex mode: full
        flowctrl: none
        irq moderation: disabled
        tcp offload: enabled
        scatter-gather: enabled
        tx-checksum: enabled
        rx-checksum: enabled
        rx-polling: enabled
    eth1: no IPv6 routers present
    usbcore: deregistering driver usbnet
    eth0: unregister usbnet usb-0000:00:1d.7-6, Netgear FA-120 USB Ethernet
    usb 1-6: USB disconnect, address 6
    eth1: network connection down
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) ->
    IRQ 4
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
          PrefPort:A RlmtMode:Check Link State
    eth0: network connection up using port A
        speed: 100
        autonegotiation: yes
        duplex mode: full
        flowctrl: none
        irq moderation: disabled
        tcp offload: enabled
        scatter-gather: enabled
        tx-checksum: enabled
        rx-checksum: enabled
        rx-polling: enabled
    eth0: network connection down
    eth0: network connection up using port A
        speed: 100
        autonegotiation: yes
        duplex mode: full
        flowctrl: none
        irq moderation: disabled
        tcp offload: enabled
        scatter-gather: enabled
        tx-checksum: enabled
        rx-checksum: enabled
        rx-polling: enabled
    eth0: no IPv6 routers present
    eth0: network connection down
    eth0: network connection up using port A
        speed: 100
        autonegotiation: yes
        duplex mode: full
        flowctrl: none
        irq moderation: disabled
        tcp offload: enabled
        scatter-gather: enabled
        tx-checksum: enabled
        rx-checksum: enabled
        rx-polling: enabled
    eth0: no IPv6 routers present
    eth0: network connection down
    eth0: network connection up using port A
        speed: 100
        autonegotiation: yes
        duplex mode: full
        flowctrl: none
        irq moderation: disabled
        tcp offload: enabled
        scatter-gather: enabled
        tx-checksum: enabled
        rx-checksum: enabled
        rx-polling: enabled
    eth0: no IPv6 routers present
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  • Next message: Daniel Phillips: "[RFC][PATCH 2 of 4] Configfs is really sysfs"