[ 0.000000] Bootdata ok (command line is console=ttyS0,9600 console=tty0 ro rhgb root=LABEL=/ devfs=nomount max_loop=16 acpi=on) [ 0.000000] Linux version 2.6.14 (root@aspc12.as.arizona.edu) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #8 SMP Sun Nov 6 17:28:39 MST 2005 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 0000000000098000 (usable) [ 0.000000] BIOS-e820: 0000000000098000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000c2000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000aff20000 (usable) [ 0.000000] BIOS-e820: 00000000aff20000 - 00000000aff2f000 (ACPI data) [ 0.000000] BIOS-e820: 00000000aff2f000 - 00000000aff80000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000aff80000 - 00000000b0000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000400000000 (usable) [ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0 [ 0.000000] SRAT: PXM 1 -> APIC 1 -> Node 1 [ 0.000000] SRAT: Node 0 PXM 0 0-9ffff [ 0.0000000 PXM 0 0-afffffff [ 0.000000] SRAT: Node 0 PXM 0 0-1ffffffff [ 0.000000] SRAT: Node 1 PXM 1 200000000-3ffffffff [ 0.000000] Bootmem setup node 0 0000000000000000-00000001ffffffff [ 0.000000] Bootmem setup node 1 0000000200000000-00000003ffffffff [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:5 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 15:5 APIC version 16 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xd0000000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 3, version 17, address 0xd0000000, GSI 24-27 [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xd0001000] gsi_base[28]) [ 0.000000] IOAPIC[2]: apic_id 4, version 17, address 0xd0001000, GSI 28-31 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at b4000000 (gap: b0000000:30000000) [ 0.000000] Checking aperture... [ 0.000000] CPU 0: aperture @ c000000 size 32 MB [ 0.000000] Aperture from northbridge cpu 0 too small (32 MB) [ 0.000000] No AGP bridge found [ 0.000000] Your BIOS doesn't leave a aperture memory hole [ 0.000000] Please enable the IOMMU option in the BIOS setup [ 0.000000] This costs you 64 MB of RAM [ 0.000000] Mapping aperture over 65536 KB of RAM @ c000000 [ 0.000000] Built 2 zonelists [ 0.000000] Kernel command line: console=ttyS0,9600 console=tty0 ro rhgb root=LABEL=/ devfs=nomount max_loop=16 acpi=on [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes) [ 0.000000] time.c: Using 3.579545 MHz PM timer. [ 0.000000] time.c: Detected 2010.314 MHz processor. [ 108.105324] Console: colour VGA+ 80x25 [ 112.375617] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 112.489711] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 113.124861] Memory: 15135176k/16777216k available (4917k kernel code, 330008k reserved, 3087k data, 272k init) [ 113.399678] Calibrating delay using timer specific routine.. 4023.95 BogoMIPS (lpj=20119773) [ 113.510791] Mount-cache hash table entries: 256 [ 113.570372] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 113.664200] CPU: L2 Cache: 1024K (64 bytes/line) [ 113.724786] CPU 0(1) -> Node 0 -> Core 0 [ 113.776231] mtrr: v2.0 (20020519) [ 113.820608] tbxface-0109 [02] load_tables : ACPI Tables successfully acquired [ 113.931295] Parsing all Control Methods:....................................................................................................................................................................................................... [ 114.229585] Table [DSDT](id 0006) - 563 Objects with 71 Devices 199 Methods 24 Regions [ 114.336147] Parsing all Control Methods: [ 114.385466] Table [SSDT](id 0004) - 6 Objects with 0 Devices 0 Methods 0 Regions [ 114.484986] ACPI Namespace successfully loaded at root ffffffff8090b080 [ 114.572097] evxfevnt-0091 [03] enable : Transition to ACPI mode successful [ 114.780018] Using local APIC timer interrupts. [ 114.888028] Detected 12.564 MHz APIC timer. [ 114.943010] softlockup thread 0 started up. [ 114.998011] Booting processor 1/2 APIC 0x1 [ 115.062075] Initializing CPU#1 [ 115.208365] Calibrating delay using timer specific routine.. 4020.73 BogoMIPS (lpj=20103651) [ 115.208373] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 115.208375] CPU: L2 Cache: 1024K (64 bytes/line) [ 115.208378] CPU 1(1) -> Node 1 -> Core 0 [ 115.208509] Am) Processor 838 stepping 0a [ 115.208519] CPU 1: Syncing TSC to CPU 0. [ 115.208707] CPU 1: synchronized TSC with CPU 0 (last diff -111 cycles, maxerr 1062 cycles) [ 115.208713] Brought up 2 CPUs [ 115.208727] softlockup thread 1 started up. [ 115.885788] Disabling vsyscall due to use of PM timer [ 115.952172] time.c: Using PM based timekeeping. [ 116.011614] testing NMI watchdog ... OK. [ 116.163303] checking if image is initramfs... it is [ 116.302924] NET: Registered protocol family 16 [ 116.361340] ACPI: bus type pci registered [ 116.414253] PCI: Using configuration type 1 [ 116.470559] ACPI: Subsystem revision 20050902 [ 116.529489] evgpeblk-0988 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 [ 116.640555] evgpeblk-0996 [06] ev_create_gpe_block : Found 6 Wake, Enabled 1 Runtime GPEs in this block [ 116.767992] Completing Region/Field/Buffer/Package initialization:................................................................... [ 116.930502] Initialized 24/24 Regions 1/1 Fields 25/25 Buffers 17/30 Packages (578 nodes) [ 117.040346] Executing all Device _STA and_INI methods:............................................................................. [ 117.198853] 77 Devices found containing: 77 _STA, 0 _INI methods [ 117.280134] ACPI: Interpreter enabled [ 117.328213] ACPI: Using IOAPIC for interrupt routing [ 117.396480] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 117.459367] PCI: Probing PCI hardware (bus 00) [ 117.517871] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 [ 117.596491] PCI: Transparent bridge - 0000:00:09.0 [ 117.761150] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0 [ 117.841985] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0 [ 117.922827] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0 [ 118.005142] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0, disabled. [ 118.098571] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled. [ 118.191996] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled. [ 118.285420] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0 [ 118.366267] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0 [ 118.447126] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled. [ 118.540547] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled. [ 118.633973] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled. [ 118.727403] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled. [ 118.820844] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0 [ 118.901698] ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled. [ 118.995124] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. [ 119.088176] ACPI: PCI Root Bridge [PCI2] (0000:08) [ 119.151131] PCI: Probing PCI hardware (bus 08) [ 119.209633] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 [ 119.291071] Linux Plug and Play Support v0.97 (c) Adam Belay [ 119.365433] pnp: PnP ACPI init [ 119.417993] pnp: PnP ACPI: found 14 devices [ 119.473108] SCSI subsystem initialized [ 119.522423] usbcore: registered new driver usbfs [ 119.583094] usbcore: registered new driver hub [ 119.641931] PCI: Using ACPI for IRQ routing [ 119.696834] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 119.805615] NET: Registered protocol family 23 [ 119.864015] PCI-DMA: Disabling AGP. [ 119.909814] PCI-DMA: aperture base @ c000000 size 65536 KB [ 119.981894] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 120.068068] pnp: 00:01: ioport range 0x8000-0x807f could not be reserved [ 120.156173] pnp: 00:01: ioport range 0x8080-0x80ff has been reserved [ 120.239623] pnp: 00:01: ioport range 0x8400-0x847f has been reserved [ 120.323071] pnp: 00:01: ioport range 0x8480-0x84ff has been reserved [ 120.406524] pnp: 00:01: ioport range 0x8800-0x887f has been reserved [ 120.489973] pnp: 00:01: ioport range 0x8880-0x88ff has been reserved [ 120.573423] pnp: 00:01: ioport range 0x5000-0x503f has been reserved [ 120.656872] pnp: 00:01: ioport range 0x5040-0x507f has been reserved [ 120.742422] PCI: Bridge: 0000:00:09.0 [ 120.790519] IO window: 2000-2fff [ 120.835102] MEM window: b0100000-b1ffffff [ 120.889974] PREFETCH window: b80 [ 120.950560] PCI: Bridge: 0000:00:0d.0 [ 120.998571] IO window: disabled. [ 121.043156] MEM window: disabled. [ 121.088881] PREFETCH window: disabled. [ 121.140329] PCI: Bridge: 0000:00:0e.0 [ 121.188336] IO window: disabled. [ 121.232920] MEM window: b2000000-b7ffffff [ 121.287790] PREFETCH window: c0000000-cfffffff [ 121.348391] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 121.451269] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 121.554149] PCI: Bridge: 0000:08:0a.0 [ 121.602157] IO window: disabled. [ 121.646741] MEM window: disabled. [ 121.692469] PREFETCH window: disabled. [ 121.743927] PCI: Bridge: 0000:08:0b.0 [ 121.792026] IO window: 3000-3fff [ 121.836610] MEM window: d0100000-d01fffff [ 121.891482] PREFETCH window: d0800000-d0ffffff [ 121.952475] Simple Boot Flag at 0x36 set to 0x1 [ 122.014000] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ [ 122.128056] Total HugeTLB memory allocated, 0 [ 122.185459] VFS: Disk quotas dquot_6.5.1 [ 122.236941] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 122.321726] Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu [ 122.407513] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 122.491265] NTFS driver 2.1.24 [Flags: R/W]. [ 122.547397] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [ 122.673457] Initializing Cryptographic API [ 122.727316] PCI: MSI quirk detected. pci_msi_quirk set. [ 122.795996] PCI: MSI quirk detected. pci_msi_quirk set. [ 122.865054] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS [ 122.963535] assign_interrupt_mode Found MSI capability [ 123.031004] PCI: MSI quirk detected. MSI disabled. [ 123.093995] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS [ 123.192410] assign_interrupt_mode Found MSI capability [ 123.260766] vga16fb: mapped to 0xffff8100000a0000 [ 123.631994] Console: switching to colour frame buffer device 80x30 [ 123.713884] fb0: VGA16 VGA frame buffer device [ 123.713920] ACPI: Power Button (FF) [PWRF] [ 123.713937] ACPI: Power Button (CM) [PWRB] [ 123.773738] ACPI: CPU0 (power states: C1[C1]) [ 123.773787] ACPI: CPU1 (power states: C1[C1]) [ 123.773810] acpi_processor-0702 [08] is_processor_present : Processor Device is not present [ 123.773815] acpi_processor-0507 [06] processor_get_info : Error getting cpuindex for acpiid 0x2 [ 123.773832] acpi_processor-0702 [08] is_processor_present : Processor Device is not present [ 123.773835] acpi_processor-0507 [06] processor_get_info : Error getting cpuindex for acpiid 0x3 [ 123.957567] Real Time Clock Driver v1.12 [ 123.957862] Linux agpgart interface v0.101 (c) Dave Jones [ 123.957865] ipmi message handler version 36.0 [ 123.958457] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 123.962534] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 123.962781] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 123.963904] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 123.964541] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 123.965184] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 123.967763] ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A [ 123.968972] ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A [ 123.970166] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 123.970587] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 123.971166] io scheduler noop registered [ 123.971198] io scheduler anticipatory registered [ 123.971211] io scheduler deadline registered [ 123.971239] io scheduler cfq registered [ 123.971304] Floppy drive(s): fd0 is 1.44M [ 125.770997] FDC 0 is a post-1991 82077 [ 125.833116] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize [ 125.948958] loop: loaded (max 16 devices) [ 126.010845] pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com [ 126.128101] nbd: registered device at major 43 [ 126.197653] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 126.286272] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 126.401267] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 [ 126.486565] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 126.599838] NFORCE-CK804: chipset revision 162 [ 126.663120] NFORCE-CK804: not 100% native mode: will probe irqs later [ 126.752912] NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller [ 126.839381] ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:DMA, hdb:DMA [ 126.945272] ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:DMA, hdd:DMA [ 127.363881] hda: Maxtor 6Y250P0, ATA DISK drive [ 127.733606] hdb: MAXTOR 5A320J8, ATA DISK drive [ 127.853953] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 128.353150] hdc: SONY CD-RW CRX210E1, ATAPI CD/DVD-ROM drive [ 129.272471] hdd: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive [ 129.405917] ide1 at 0x170-0x177,0x376 on irq 15 [ 129.473523] hda: max request size: 1024KiB [ 129.539688] hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63, UDMA(133) [ 129.661946] hda: cache flushes supported [ 129.719512] hda: hda1 hda2 hda3 hda4 [ 129.793258] hdb: max request size: 1024KiB [ 129.853347] hdb: 632672208 sectors (323928 MB) w/2048KiB Cache, CHS=39382/255/63, UDMA(133) [ 129.975074] hdb: cache flushes supported [ 130.032303] hdb: hdb1 hdb2 hdb3 hdb4 [ 130.106450] hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) [ 130.199520] Uniform CD-ROM driver Revision: 3.20 [ 130.304513] hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 130.395475] ide-floppy driver 0.99.newide [ 130.454148] 3ware 9000 Storage Controller device driver for Linux v2.26.02.004. [ 130.561610] ACPI: PCI Interrupt 0000:0a:03.0[A] -> GSI 30 (level, low) -> IRQ 177 [ 152.375361] 3w-9xxx: scsi0: AEN: WARNING (0x04:0x0042): Error during read of primary DCB:port=7, error=0x208. [ 152.635166] scsi0 : 3ware 9000 Storage Controller [ 152.702969] 3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xd0140000, IRQ: 177. [ 153.184761] 3w-9xxx: scsi0: Firmware FE9X 2.04.00.005, BIOS BE9X 2.03.01.047, Ports: 8. [ 153.302709] Vendor: 3ware Model: Logical Disk 00 Rev: 1.00 [ 153.393513] Type: Direct-Access ANSI SCSI revision: 00 [ 153.521902] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 153.639513] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23 [ 153.721919] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 185 [ 153.852909] ata1: SATA max UDMA/133 cmd 0x1440 ctl 0x1436 bmdma 0x1410 irq 185 [ 153.962337] ata2: SATA max UDMA/133 cmd 0x1438 ctl 0x1432 bmdma 0x1418 irq 185 [ 154.463912] ata1: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48 [ 154.554027] ata1(0): applying bridge limits [ 154.618023] nv_sata: Primary device added [ 154.678102] nv_sata: Primary device removed [ 154.740146] nv_sata: Secondary device added [ 154.801981] nv_sata: Secondary device removed [ 154.865820] ata1: dev 0 configured for UDMA/100 [ 154.931787] scsi1 : sata_nv [ 155.363246] ata2: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48 [ 155.452233] ata2(0): applying bridge limits [ 155.514806] nv_sata: Primary device added [ 155.573610] nv_sata: Primary device removed [ 155.634508] nv_sata: Secondary device added [ 155.695199] nv_sata: Secondary device removed [ 155.758000] ata2: dev 0 configured for UDMA/100 [ 155.822928] scsi2 : sata_nv [ 155.864982] Vendor: ATA Model: WDC WD2500JD-22F Rev: 02.0 [ 155.954600] Type: Direct-Access ANSI SCSI revision: 05 [ 156.062259] Vendor: ATA Model: WDC WD2500JD-22F Rev: 02.0 [ 156.151739] Type: Direct-Access ANSI SCSI revision: 05 [ 156.258679] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 156.372259] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22 [ 156.452503] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 193 [ 156.579309] ata3: SATA max UDMA/133 cmd 0x1458 ctl 0x144E bmdma 0x1420 irq 193 [ 156.684918] ata4: SATA max UDMA/133 cmd 0x1450 ctl 0x144A bmdma 0x1428 irq 193 [ 157.001945] ata3: no device found (phy stat 00000000) [ 157.074475] scsi3 : sata_nv [ 157.321709] ata4: no device found (phy stat 00000000) [ 157.394246] scsi4 : sata_nv [ 157.438353] st: Version 20050830, fixed bufsize 32768, s/g segs 256 [ 157.527676] SCSI device sda: 3417817088 512-byte hdwr sectors (1749922 MB) [ 157.626590] SCSI device sda: drive cache: write back, no read (daft) [ 157.717087] SCSI device sda: 3417817088 512-byte hdwr sectors (1749922 MB) [ 157.816256] SCSI device sda: drive cache: write back, no read (daft) [ 157.906592] sda: sda1 [ 157.961429] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 [ 158.050772] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [ 158.145830] SCSI device sdb: drive cache: write back [ 158.218032] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [ 158.313068] SCSI device sdb: ache: write back [ 158.385156] sdb: sdb1 [ 158.441035] Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 [ 158.530272] SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB) [ 158.625124] SCSI device sdc: drive cache: write back [ 158.697108] SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB) [ 158.791736] SCSI device sdc: drive cache: write back [ 158.863305] sdc: sdc1 [ 158.916372] Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0 [ 159.005420] Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 [ 159.113725] Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0 [ 159.222844] Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0 [ 159.332631] I2O subsystem v1.288 [ 159.381889] i2o: max drivers = 8 [ 159.431686] I2O Configuration OSM v1.248 [ 159.490364] I2O Block Device OSM v1.287 [ 159.547726] I2O SCSI Peripheral OSM v1.282 [ 159.607979] I2O ProcFS OSM v1.145 [ 159.658740] video1394: Installed video1394 module [ 159.726748] ieee1394: raw1394: /dev/raw1394 device initialized [ 159.809583] sbp2: $Rev: 1306 $ Ben Collins [ 159.894639] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 159.992222] ieee1394: sbp2: Try serialize_io=0 for better performance [ 160.083055] usbmon: debugfs is not available [ 160.145159] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 160.261293] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21 [ 160.343075] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, high) -> IRQ 201 [ 160.472868] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 160.547831] ehci_hcd 0000:00:02.1: debug port 1 [ 160.613610] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 160.722396] ehci_hcd 0000:00:02.1: irq 201, io mem 0xb0001000 [ 160.803589] ehci_hcd 0000:00:02.1: park 0 [ 160.861547] ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 [ 162.881951] usb usb1: Product: EHCI Host Controller [ 162.951542] usb usb1: Manufacturer: Linux 2.6.14 ehci_hcd [ 163.027923] usb usb1: SerialNumber: 0000:00:02.1 [ 163.094468] hub 1-0:1.0: USB hub found [ 163.149312] hub 1-0:1.0: 10 ports detected [ 163.317870] acpi_bus-0200 [01] bus_set_power : Device is not power manageable [ 163.433220] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20 [ 163.514707] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 20 (level, high) -> IRQ 209 [ 163.643811] ohci_hcd 0000:00:02.0: OHtroller [ 163.920897] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 164.029962] ohci_hcd 0000:00:02.0: irq 209, io mem 0xb0000000 [ 164.168768] usb usb2: Product: OHCI Host Controller [ 164.238734] usb usb2: Manufacturer: Linux 2.6.14 ohci_hcd [ 164.315324] usb usb2: SerialNumber: 0000:00:02.0 [ 164.381859] hub 2-0:1.0: USB hub found [ 164.436718] hub 2-0:1.0: 10 ports detected [ 164.606842] USB Universal Host Controller Interface driver v2.3 [ 165.026028] usb 2-3: new full speed USB device using ohci_hcd and address 2 [ 165.345979] hub 2-3:1.0: USB hub found [ 165.401768] hub 2-3:1.0: 4 ports detected [ 165.586276] usbcore: registered new driver hiddev [ 165.897400] usb 2-3.1: new low speed USB device using ohci_hcd and address 3 [ 166.160207] usb 2-3.1: Product: USB Receiver [ 166.221694] usb 2-3.1: Manufacturer: Logitech [ 166.316469] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-3.1 [ 166.477972] drivers/usb/input/hid-core.c: ctrl urb status -110 received [ 166.573901] drivers/usb/input/hid-core.c: ctrl urb status -110 received [ 166.666776] <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 166.801280] input<7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 166.941576] : USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-3.1 [ 167.051217] usbcore: registered new driver usbhid [ 167.118671] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 167.205816] usbcore: registered new driver usbserial [ 167.276887] drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic [ 167.392974] usbcore: registered new driver usbserial_generic [ 167.473558] drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 [ 167.567970] drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS [ 167.705993] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5 [ 167.829543] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0 [ 167.953223] usbcore: registered new driver visor [ 168.020298] drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1 [ 168.133425] mice: PS/2 mouse device common for all mice [ 168.208613] input: PC Speaker [ 168.254023] Driver for 1-wire Dallas network protocol. [ 168.328798] md: linear personality registered as nr 1 [ 168.401596] md: raid0 personality registered as nr 2 [ 168.473112] md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27 [ 168.558210] md: bitmap version 3.39 [ 168.610051] Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC). [ 168.746244] ALSA device list: [ 168.790995] No soundcards found. [ 168.841574] oprofile: using NMI interrupt. [ 168.901160] NET: Registered protocol family 2 [ 169.083110] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 169.193965] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 169.307307] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 169.402060] TCP: Hash tables configured (established 262144 bind 65536) [ 169.495075] TCP reno registered [ 169.542370] ip_conntrack version 2.3 (8192 buckets, 65536 max) - 296 bytes per conntrack [ 169.972411] ip_tables: (C) 2000-2002 Netfilter core team [ 170.292255] TCP bic registered [ 170.338425] NET: Registered protocol family 1 [ 170.401601] NET: Registered protocol family 17 [ 170.465831] IrCOMM protocol (Dag Brattli) [ 170.534237] ACPI wakeup devices: [ 170.583460] PCI0 <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110 [ 170.724807] PS2M <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110 [ 170.866547] PS2K <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110 [ 171.008411] COM1 <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110 [ 171.150985] COM2 <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110 [ 171.294097] USB0 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 171.436981] USB2 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 171.579782] MAC0 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 171.722771] P2P0 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 171.865675] XVR0 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 172.008663] XVR1 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 172.152397] XVR2 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 172.296843] XVR3 <7>ohci_hcd 0000:00:02.0: urb ffff8101ffec70c0 path 3.1 ep1in 5e160000 cc 5 --> status -110 [ 172.441512] [ 172.468417] ACPI: (supports S0 S1 S4 S5) [ 172.527779] BIOS EDD facility v0.16 2004-Jun-25, 5 devices found [ 172.615384] Freeing unused kernel memory: 272k freed [ 172.950076] EXT3-fs: INFO: recovery required on readonly filesystem. [ 173.038962] EXT3-fs: write access will be enabled during recovery. [ 174.306129] kjournald starting. Commit interval 5 seconds [ 174.300] EXT3-fs: hda3: orphan cleanup on readonly fs [ 174.318291] EXT3-fs: hda3: 3 orphan inodes deleted [ 174.318293] EXT3-fs: recovery complete. [ 174.583480] EXT3-fs: mounted filesystem with ordered data mode. [ 216.699440] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 216.851555] NFSD: starting 90-second grace period [ 835.107797] [ 835.107799] CPU 0: Machine Check Exception: 4 Bank 4: f62c20013d080813 [ 835.230479] TSC 1872b5c36c0 ADDR 1da1a8000 [ 835.285662] Kernel panic - not syncing: Machine check [ 835.352171] <7>ohci_hcd 0000:00:02.0: urb ffff810008033d40 path 3.1 ep2in 5e160000 cc 5 --> status -110