Re: [OT] 8-port AHCI SATA Controller?
- From: Sander <sander@xxxxxxxxxxx>
- Date: Tue, 31 Jan 2006 19:39:29 +0100
Lennart Sorensen wrote (ao):
> > Yeah, I know, but because of their real 'hardware' raid, these cards
> > are three times more expensive per port. And I just need JBOD.
>
> Really? How much does a 24 port areca card cost? Is it 12 times the
> cost of a two port promise card?
Not sure about the two port, but for example the SX8 is 180 dollars at
pricewatch.com, while an Areca 12-port starts at 756 dollars. That is
22.5 dollars per port vs 63 dollars per port. More or less the same goes
for 3Ware.
Of course you can't compare Areca/3Ware with the SX8 feature-wise, but
all I need JBOD.
Kind regards, Sander
--
Humilis IT Services and Solutions
http://www.humilis.net
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Follow-Ups:
- Re: [OT] 8-port AHCI SATA Controller?
- From: Lennart Sorensen
- Re: [OT] 8-port AHCI SATA Controller?
- References:
- [OT] 8-port AHCI SATA Controller?
- From: Sander
- Re: [OT] 8-port AHCI SATA Controller?
- From: Lennart Sorensen
- Re: [OT] 8-port AHCI SATA Controller?
- From: Sander
- Re: [OT] 8-port AHCI SATA Controller?
- From: Lennart Sorensen
- [OT] 8-port AHCI SATA Controller?
- Prev by Date: Re: 2.6.16-rc1-mm4: ACX=y, ACX_USB=n compile error
- Next by Date: Re: How to map high memory for block io
- Previous by thread: Re: [OT] 8-port AHCI SATA Controller?
- Next by thread: Re: [OT] 8-port AHCI SATA Controller?
- Index(es):
Relevant Pages
- 3Com Megahertz 3CXEM556 B Multifunction Card Not Working
... 3CXEM556 B Ethernet/56K Modem PCMCIA card working on FreeBSD 5.1 on ...
pci0: <PCI bus> on pcib0 ... atapci0: port ... (freebsd-net) - 3Com Megahertz 3CXEM556 B Multifunction Card Not Working
... 3CXEM556 B Ethernet/56K Modem PCMCIA card working on FreeBSD 5.1 on ...
pci0: <PCI bus> on pcib0 ... atapci0: port ... (freebsd-questions) - Re: adding new card in cisco switch 6506
... Port AuxiliaryVlan AuxVlan-Status InlinePowered PowerAllocated ... Line Card
Status for Module 1: ... set vlan 1 name default type ethernet mtu 1500 said 100001 state
active ... set logging level mcast 6 default ... (comp.dcom.sys.cisco) - 5.2.1 - Dolphin 4036 4 port serial? (port 3/4 not recogniced) (repost)
... I built in a card which is identified as Dolphin 4036. ... But there is no way
to get sio6 and 7 (3rd/4th port on the card) working. ... pci_cfgintr: 0:11 INTA BIOS
irq 11 ... on miibus0 ... (freebsd-current) - RE: Wireless PCI card setup
... <Parallel port bus> on ppc0 ... unknown: can't assign resources
... I have been able to bring the card up ... (freebsd-questions)