Re: [OT] 8-port AHCI SATA Controller?
- From: lsorense@xxxxxxxxxxxxxxxxxxx (Lennart Sorensen)
- Date: Tue, 31 Jan 2006 13:44:28 -0500
On Tue, Jan 31, 2006 at 07:39:29PM +0100, Sander wrote:
> Not sure about the two port, but for example the SX8 is 180 dollars at
> pricewatch.com, while an Areca 12-port starts at 756 dollars. That is
> 22.5 dollars per port vs 63 dollars per port. More or less the same goes
> for 3Ware.
Hmm, well the 24 port is listed at 1278, so less per port than the 12
port for sure, but if you only need 8, then well... :)
Of course I doubt there is that big a market for an 8 port NON raid
card, which might explain why there doesn't seem to be any. Of course
if there aren't any it is hard to have a market exist for them.
> Of course you can't compare Areca/3Ware with the SX8 feature-wise, but
> all I need JBOD.
Well personally I have never seen more than 4 ports per card on a non
hardware raid card. That doesn't mean they don't exist, but it makes it
a lot less likely that they exist in my book. :)
Len Sorensen
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
- Follow-Ups:
- Re: [OT] 8-port AHCI SATA Controller?
- From: Sander
- Re: [OT] 8-port AHCI SATA Controller?
- References:
- [OT] 8-port AHCI SATA Controller?
- From: Sander
- Re: [OT] 8-port AHCI SATA Controller?
- From: Lennart Sorensen
- Re: [OT] 8-port AHCI SATA Controller?
- From: Sander
- Re: [OT] 8-port AHCI SATA Controller?
- From: Lennart Sorensen
- Re: [OT] 8-port AHCI SATA Controller?
- From: Sander
- [OT] 8-port AHCI SATA Controller?
- Prev by Date: Re: [OT] 8-port AHCI SATA Controller?
- Next by Date: Re: [PATCH/RFC] Shared page tables
- Previous by thread: Re: [OT] 8-port AHCI SATA Controller?
- Next by thread: Re: [OT] 8-port AHCI SATA Controller?
- Index(es):
Relevant Pages
- 3Com Megahertz 3CXEM556 B Multifunction Card Not Working
... 3CXEM556 B Ethernet/56K Modem PCMCIA card working on FreeBSD 5.1 on ...
pci0: <PCI bus> on pcib0 ... atapci0: port ... (freebsd-net) - 3Com Megahertz 3CXEM556 B Multifunction Card Not Working
... 3CXEM556 B Ethernet/56K Modem PCMCIA card working on FreeBSD 5.1 on ...
pci0: <PCI bus> on pcib0 ... atapci0: port ... (freebsd-questions) - Re: adding new card in cisco switch 6506
... Port AuxiliaryVlan AuxVlan-Status InlinePowered PowerAllocated ... Line Card
Status for Module 1: ... set vlan 1 name default type ethernet mtu 1500 said 100001 state
active ... set logging level mcast 6 default ... (comp.dcom.sys.cisco) - 5.2.1 - Dolphin 4036 4 port serial? (port 3/4 not recogniced) (repost)
... I built in a card which is identified as Dolphin 4036. ... But there is no way
to get sio6 and 7 (3rd/4th port on the card) working. ... pci_cfgintr: 0:11 INTA BIOS
irq 11 ... on miibus0 ... (freebsd-current) - RE: Wireless PCI card setup
... <Parallel port bus> on ppc0 ... unknown: can't assign resources
... I have been able to bring the card up ... (freebsd-questions)