[PATCH 10/20] omapfb: Add support for the ZOOM MDK LCD

From: Stanley.Miao <stanley.miao@xxxxxxxxxxxxx>

Add glue to control the OMAP_LDP LCD as a frame buffer device
using the existing dispc.c driver under omapfb.

Patch updated for mainline kernel. Note that the
drivers/video/omap should be updated to pass omap_lcd_config
in platform_data. The patch should also be updated to compile
if twl4030 is not selected, and eventually to use the regulator
framework.

Fixed-by: Jarkko Nikula <jarkko.nikula@xxxxxxxxx>
Fixed-by: Tony Lindgren <tony@xxxxxxxxxxx>
Signed-off-by: Stanley.Miao <stanley.miao@xxxxxxxxxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx>
Acked-by: Krzysztof Helt <krzysztof.h1@xxxxx>
---
arch/arm/configs/omap_ldp_defconfig | 54 +++++++++-
drivers/video/omap/Kconfig | 4 +
drivers/video/omap/Makefile | 1 +
drivers/video/omap/lcd_ldp.c | 200 +++++++++++++++++++++++++++++++++++
4 files changed, 257 insertions(+), 2 deletions(-)
create mode 100644 drivers/video/omap/lcd_ldp.c

diff --git a/arch/arm/configs/omap_ldp_defconfig b/arch/arm/configs/omap_ldp_defconfig
index 679a4a3..b9c4891 100644
--- a/arch/arm/configs/omap_ldp_defconfig
+++ b/arch/arm/configs/omap_ldp_defconfig
@@ -690,6 +690,7 @@ CONFIG_GPIOLIB=y
# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y

#
# PCI GPIO expanders:
@@ -742,6 +743,7 @@ CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+CONFIG_TWL4030_CORE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
@@ -767,8 +769,46 @@ CONFIG_DAB=y
#
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+CONFIG_FB_OMAP=y
+CONFIG_FB_OMAP_LCD_VGA=y
+# CONFIG_FB_OMAP_LCDC_EXTERNAL is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE=4
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
+# CONFIG_LCD_VGG2432A4 is not set
+CONFIG_LCD_PLATFORM=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_CORGI is not set
+# CONFIG_BACKLIGHT_GENERIC is not set

#
# Display device support
@@ -780,6 +820,16 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=y
CONFIG_SND=y
# CONFIG_SND_SEQUENCER is not set
diff --git a/drivers/video/omap/Kconfig b/drivers/video/omap/Kconfig
index eb05e09..2bffc07 100644
--- a/drivers/video/omap/Kconfig
+++ b/drivers/video/omap/Kconfig
@@ -7,6 +7,10 @@ config FB_OMAP
help
Frame buffer driver for OMAP based boards.

+config FB_OMAP_LCD_VGA
+ bool "Use LCD in VGA mode"
+ depends on MACH_OMAP_3430SDP || MACH_OMAP_LDP
+
choice
depends on FB_OMAP && MACH_OVERO
prompt "Screen resolution"
diff --git a/drivers/video/omap/Makefile b/drivers/video/omap/Makefile
index 0d2996a..b63b198 100644
--- a/drivers/video/omap/Makefile
+++ b/drivers/video/omap/Makefile
@@ -29,6 +29,7 @@ objs-y$(CONFIG_MACH_OMAP_OSK) += lcd_osk.o
objs-y$(CONFIG_MACH_OMAP_APOLLON) += lcd_apollon.o
objs-y$(CONFIG_MACH_OMAP_2430SDP) += lcd_2430sdp.o
objs-y$(CONFIG_MACH_OMAP_3430SDP) += lcd_2430sdp.o
+objs-y$(CONFIG_MACH_OMAP_LDP) += lcd_ldp.o
objs-y$(CONFIG_MACH_OMAP2EVM) += lcd_omap2evm.o
objs-y$(CONFIG_MACH_OMAP3EVM) += lcd_omap3evm.o
objs-y$(CONFIG_MACH_OMAP3_BEAGLE) += lcd_omap3beagle.o
diff --git a/drivers/video/omap/lcd_ldp.c b/drivers/video/omap/lcd_ldp.c
new file mode 100644
index 0000000..dbfe897
--- /dev/null
+++ b/drivers/video/omap/lcd_ldp.c
@@ -0,0 +1,200 @@
+/*
+ * LCD panel support for the TI LDP board
+ *
+ * Copyright (C) 2007 WindRiver
+ * Author: Stanley Miao <stanley.miao@xxxxxxxxxxxxx>
+ *
+ * Derived from drivers/video/omap/lcd-2430sdp.c
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/i2c/twl4030.h>
+
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/omapfb.h>
+#include <asm/mach-types.h>
+
+#define LCD_PANEL_BACKLIGHT_GPIO (15 + OMAP_MAX_GPIO_LINES)
+#define LCD_PANEL_ENABLE_GPIO (7 + OMAP_MAX_GPIO_LINES)
+
+#define LCD_PANEL_RESET_GPIO 55
+#define LCD_PANEL_QVGA_GPIO 56
+
+#ifdef CONFIG_FB_OMAP_LCD_VGA
+#define LCD_XRES 480
+#define LCD_YRES 640
+#define LCD_PIXCLOCK_MAX 41700
+#else
+#define LCD_XRES 240
+#define LCD_YRES 320
+#define LCD_PIXCLOCK_MAX 185186
+#endif
+
+#define PM_RECEIVER TWL4030_MODULE_PM_RECEIVER
+#define ENABLE_VAUX2_DEDICATED 0x09
+#define ENABLE_VAUX2_DEV_GRP 0x20
+#define ENABLE_VAUX3_DEDICATED 0x03
+#define ENABLE_VAUX3_DEV_GRP 0x20
+
+#define ENABLE_VPLL2_DEDICATED 0x05
+#define ENABLE_VPLL2_DEV_GRP 0xE0
+#define TWL4030_VPLL2_DEV_GRP 0x33
+#define TWL4030_VPLL2_DEDICATED 0x36
+
+#define t2_out(c, r, v) twl4030_i2c_write_u8(c, r, v)
+
+
+static int ldp_panel_init(struct lcd_panel *panel,
+ struct omapfb_device *fbdev)
+{
+ gpio_request(LCD_PANEL_RESET_GPIO, "lcd reset");
+ gpio_request(LCD_PANEL_QVGA_GPIO, "lcd qvga");
+ gpio_request(LCD_PANEL_ENABLE_GPIO, "lcd panel");
+ gpio_request(LCD_PANEL_BACKLIGHT_GPIO, "lcd backlight");
+
+ gpio_direction_output(LCD_PANEL_QVGA_GPIO, 0);
+ gpio_direction_output(LCD_PANEL_RESET_GPIO, 0);
+ gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
+ gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 0);
+
+#ifdef CONFIG_FB_OMAP_LCD_VGA
+ gpio_set_value(LCD_PANEL_QVGA_GPIO, 0);
+#else
+ gpio_set_value(LCD_PANEL_QVGA_GPIO, 1);
+#endif
+ gpio_set_value(LCD_PANEL_RESET_GPIO, 1);
+
+ return 0;
+}
+
+static void ldp_panel_cleanup(struct lcd_panel *panel)
+{
+ gpio_free(LCD_PANEL_BACKLIGHT_GPIO);
+ gpio_free(LCD_PANEL_ENABLE_GPIO);
+ gpio_free(LCD_PANEL_QVGA_GPIO);
+ gpio_free(LCD_PANEL_RESET_GPIO);
+}
+
+static int ldp_panel_enable(struct lcd_panel *panel)
+{
+ if (0 != t2_out(PM_RECEIVER, ENABLE_VPLL2_DEDICATED,
+ TWL4030_VPLL2_DEDICATED))
+ return -EIO;
+ if (0 != t2_out(PM_RECEIVER, ENABLE_VPLL2_DEV_GRP,
+ TWL4030_VPLL2_DEV_GRP))
+ return -EIO;
+
+ gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 1);
+ gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 1);
+
+ if (0 != t2_out(PM_RECEIVER, ENABLE_VAUX3_DEDICATED,
+ TWL4030_VAUX3_DEDICATED))
+ return -EIO;
+ if (0 != t2_out(PM_RECEIVER, ENABLE_VAUX3_DEV_GRP,
+ TWL4030_VAUX3_DEV_GRP))
+ return -EIO;
+
+ return 0;
+}
+
+static void ldp_panel_disable(struct lcd_panel *panel)
+{
+ gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
+ gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 0);
+
+ t2_out(PM_RECEIVER, 0x0, TWL4030_VPLL2_DEDICATED);
+ t2_out(PM_RECEIVER, 0x0, TWL4030_VPLL2_DEV_GRP);
+ msleep(4);
+}
+
+static unsigned long ldp_panel_get_caps(struct lcd_panel *panel)
+{
+ return 0;
+}
+
+struct lcd_panel ldp_panel = {
+ .name = "ldp",
+ .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
+ OMAP_LCDC_INV_HSYNC,
+
+ .bpp = 16,
+ .data_lines = 18,
+ .x_res = LCD_XRES,
+ .y_res = LCD_YRES,
+ .hsw = 3, /* hsync_len (4) - 1 */
+ .hfp = 3, /* right_margin (4) - 1 */
+ .hbp = 39, /* left_margin (40) - 1 */
+ .vsw = 1, /* vsync_len (2) - 1 */
+ .vfp = 2, /* lower_margin */
+ .vbp = 7, /* upper_margin (8) - 1 */
+
+ .pixel_clock = LCD_PIXCLOCK_MAX,
+
+ .init = ldp_panel_init,
+ .cleanup = ldp_panel_cleanup,
+ .enable = ldp_panel_enable,
+ .disable = ldp_panel_disable,
+ .get_caps = ldp_panel_get_caps,
+};
+
+static int ldp_panel_probe(struct platform_device *pdev)
+{
+ omapfb_register_panel(&ldp_panel);
+ return 0;
+}
+
+static int ldp_panel_remove(struct platform_device *pdev)
+{
+ return 0;
+}
+
+static int ldp_panel_suspend(struct platform_device *pdev, pm_message_t mesg)
+{
+ return 0;
+}
+
+static int ldp_panel_resume(struct platform_device *pdev)
+{
+ return 0;
+}
+
+struct platform_driver ldp_panel_driver = {
+ .probe = ldp_panel_probe,
+ .remove = ldp_panel_remove,
+ .suspend = ldp_panel_suspend,
+ .resume = ldp_panel_resume,
+ .driver = {
+ .name = "ldp_lcd",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init ldp_panel_drv_init(void)
+{
+ return platform_driver_register(&ldp_panel_driver);
+}
+
+static void __exit ldp_panel_drv_exit(void)
+{
+ platform_driver_unregister(&ldp_panel_driver);
+}
+
+module_init(ldp_panel_drv_init);
+module_exit(ldp_panel_drv_exit);
--
1.6.3.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Relevant Pages

  • Re: [PATCH] uio: User IRQ Mode
    ... In this mode the user space driver ... is responsible for acknowledging and re-enabling the interrupt. ... This can easily be done without your patch. ...
    (Linux-Kernel)
  • Re: [PATCH] ne.c fix for hibernate and rmmod oops fix
    ... This patch is ready to be merged. ... that was not the case before, because the probe is invasive. ... legacy driver. ... const unsigned char *buf, const int start_page); ...
    (Linux-Kernel)
  • Re: [PATCH] Blackfin: blackfin on-chip SPI controller driver
    ... patch, rather than initial-plus-cleanups. ... Please put this in Kconfig up with the other SPI controller drivers, ... relevant points in the driver. ... place to reverse any DMA mappings ... ...
    (Linux-Kernel)
  • Re: [git patches] libata updates
    ... Bug fixes, and a new driver. ... (fixed in the attached patch). ...     else ... This is incorrect if slave/master devices use different PIO modes ...
    (Linux-Kernel)
  • Re: [patch 2.6.20-rc3 1/3] rtc-cmos driver
    ... To build your new patch for ARM I have modified the line "depends on ... configured that driver as a module. ... As for the RTC patch, it does work on the shark, and is needed. ...
    (Linux-Kernel)