Re: Disk /dev/hde doesn't contain a valid partition table {Scanned}

From: Malcolm Kay (malcolm.kay_at_internode.on.net)
Date: 09/08/04

  • Next message: Geoff Rainey (DSL AK): "RE: Disk /dev/hde doesn't contain a valid partition table {Scanned}"
    To: SW <wppiphoto@wppi.com>, General Red Hat Linux discussion list <redhat-list@redhat.com>, "Reuben D. Budiardja" <techlist@voyager.phys.utk.edu>
    Date: Wed, 8 Sep 2004 14:28:13 +0930
    
    

    On Wednesday 08 September 2004 01:07, SW wrote:
    > Hi Reuben:
    > > > I'm not sure what this means, but if I select the 'w' option, will this
    > > > destroy my data on this drive?
    > >
    > > Yes, but from what you told us from the output of fdisk, your data is
    >
    > probably
    >
    > > not retrievable or already anyway, at least recovering it is not going to
    >
    > be
    >
    > > easy.
    >
    > The data is fine on my drive. fdisk doesn't show any partitions but I can
    > retrieve and write data to the drive. fstab mounts it fine...I just
    > sometimes can't umount the drive because I get device busy, even though
    > nothing is writing to the hard drive.
    >
    > > > Also if I try to do the print option in
    > > > fdisk, it doesn't show the ext3 partition I created:
    > >
    > > ...
    > >
    > > > Could my problem be
    > > > that I ran a program which screwed up my partition table? I ran parted
    > > > which told me to run e2fsck due to a problem and then I ran fsck.ext3.
    >
    > Can
    >
    > > > any of these programs destroy my partitions?
    > >
    > > Probably..
    > >
    > > > What should I do now?
    > >
    > > Assuming you can afford loosing the data there (for good), I'd just start
    > > over. Here is a step by step guide to create ext3 partition.
    >
    > http://www.redhat.com/docs/manuals/linux/RHL-7.3-Manual/ref-guide/s1-filesy
    >stem-ext3-create.html
    >
    > I really don't want to start over as of right now the drive data is fine.
    > I'll use the steps you provided as a last resort when the *#$% hits the
    > fan. ;-)
    >

    OK, it seems you don't have partitions but a file system using the entire
    drive. Basically there is nothing wrong with that.

    The real broblem seems to be the limited view point of the backup script;
    or I guess I should say, its author.

    Malcolm

    -- 
    redhat-list mailing list
    unsubscribe mailto:redhat-list-request@redhat.com?subject=unsubscribe
    https://www.redhat.com/mailman/listinfo/redhat-list
    

  • Next message: Geoff Rainey (DSL AK): "RE: Disk /dev/hde doesn't contain a valid partition table {Scanned}"

    Relevant Pages

    • Re: Boot failure after installation
      ... You just type fdisk devname where devname is the disk device. ... You can only mount a file system. ... Use newfs to create file systems on each of the partitions except swap & c. ... Just boot it up and run it. ...
      (freebsd-questions)
    • Re: Additional HardDisk
      ... Create partitions using fdisk ... Create file system using mkfs.ext3 ... mount partitions ...
      (RedHat)
    • Re: How to format FAT32 in Windows XP?
      ... The *only* NTFS partitions it will ... Besides which, AFAIK, it is impossible for DOS-based enviroment to see NTFS partitions *unless* some NTFS driver has been loaded for it on that disk. ... what I think you are saying is that the Win9x version of FDISK will recognise and allow you to delete NTFS partitions. ... All that fdisk can do is create the partitions, it cannot give them a file system. ...
      (microsoft.public.windowsxp.general)
    • Re: hard drive limitations
      ... You select the file system when you create the partition. ... (That's why FDISK used to ask whether you wanted "large disk support". ... If you said "yes" it would create FAT32 partitions, ...
      (microsoft.public.windowsxp.general)
    • Re: Partition 1 does not end on cylinder boundary
      ... That's how FDISK displays non-FAT *PRIMARY* partitions. ... dozen or so non-FAT logical partitions that are on the disk. ... FDISK, though, seems to display non-FAT logical partitions. ...
      (comp.os.linux.setup)