[SLE] "Failed" message in startup
From: Bill Wisse (wiswp_at_niue.nu)
Date: 08/30/03
- Previous message: Richard: "[SLE] hptraid module building"
- Next in thread: Andreas Winkelmann: "Re: [SLE] "Failed" message in startup"
- Reply: Andreas Winkelmann: "Re: [SLE] "Failed" message in startup"
- Reply: Charles Philip Chan: "[SLE] Re:"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
To: suse-linux-e@suse.com Date: Fri, 29 Aug 2003 22:19:45 -1100
Hi All
Today I restarted my SuSE 8.2 box and a red message came up : "'failed".
I looked in the startup log and below you can see the result.
Although there seems to be nothing wrong , I'm still curious to find out what
and why this message came up.
Anybody an idea?
Thanks.
Options:
-a get/set fs readahead
-A set drive read-lookahead flag (0/1)
-b get/set bus state (0 == off, 1 == on, 2 == tristate)
-B set Advanced Power Management setting (1-255)
-c get/set IDE 32-bit IO setting
-C check IDE power mode status
-d get/set using_dma flag
-D enable/disable drive defect-mgmt
-E set cd-rom drive speed
-f flush buffer cache for device on exit
-g display drive geometry
-h display terse usage information
-i display drive identification
-I detailed/current information directly from drive
-Istdin similar to -I, but wants /proc/ide/*/hd?/identify as input
-k get/set keep_settings_over_reset flag (0/1)
-K set drive keep_features_over_reset flag (0/1)
-L set drive doorlock (0/1) (removable harddisks only)
-M get/set acoustic management (0-254, 128: quiet, 254: fast)
(EXPERIMENTAL)
-m get/set multiple sector count
-n get/set ignore-write-errors flag (0/1)
-p set PIO mode on IDE interface chipset (0,1,2,3,4,...)
-P set drive prefetch count
-q change next setting quietly
-Q get/set DMA tagged-queuing depth (if supported)
-r get/set readonly flag (DANGEROUS to set)
-R register an IDE interface (DANGEROUS)
-S set standby (spindown) timeout
-t perform device read timings
-T perform cache read timings
-u get/set unmaskirq flag (0/1)
-U un-register an IDE interface (DANGEROUS)
-v defaults; same as -mcudkrag for IDE drives
-V display program version and exit immediately
-w perform device reset (DANGEROUS)
-W set drive write-caching flag (0/1) (DANGEROUS)
-x tristate device for hotswap (0/1) (DANGEROUS)
-X set IDE xfer mode (DANGEROUS)
-y put IDE drive in standby mode
-Y put IDE drive to sleep
-Z disable Seagate auto-powersaving mode
-z re-read partition table
failed
--
Greetings from
/bill at 169 west , 19 south.
Disclaimer: Any errors in spelling, tact, or fact are
transmission errors."
--
Check the headers for your unsubscription address
For additional commands send e-mail to suse-linux-e-help@suse.com
Also check the archives at http://lists.suse.com
Please read the FAQs: suse-linux-e-faq@suse.com
- Previous message: Richard: "[SLE] hptraid module building"
- Next in thread: Andreas Winkelmann: "Re: [SLE] "Failed" message in startup"
- Reply: Andreas Winkelmann: "Re: [SLE] "Failed" message in startup"
- Reply: Charles Philip Chan: "[SLE] Re:"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
