Re: [SLE] DSL problem

From: Jeffrey Laramie (suse-linux-e_at_trans-star.net)
Date: 03/02/05

  • Next message: James Knott: "Re: [SLE] SLSE 9 Do I have to buy the package???"
    To: suse-linux-e@suse.com
    Date: Wed, 2 Mar 2005 09:00:09 -0500
    
    

    On Wednesday 02 March 2005 09:37, Damon Register wrote:
    > Jeffrey Laramie wrote:
    > > OK, well I think this is probably a routing problem then. It probably has
    > > to do with the point Ian made about your IP addresses. If the DSL modem
    > > insists on being 192.168.0.1 then you should change the subnet of your
    > > lan to
    >
    > I am really confused here. Why would a DSL modem be presenting an
    > address like that? Why would a modem even have an address? Are
    > you referring to the address your provider gives you? Just
    > yesterday a coworker told me about his father who had Bellsouth.
    > He said that Bellsouth was putting the users on a private subnet
    > so it was impossible for the coworker to access his fathers pc with
    > pcAnywhere. Is "your name" on such a private subnet? Is it Bellsouth?

    This may vary based on the hardware. DSL services here use routers that are
    assigned a valid external IP by the ISP and then route IPs in your subnet to
    the inet facing NIC in your firewall box or alternately to a hub/switch. If
    you connect a firewall then you use NAT/masq on the firewall to connect the
    private IPs on the lan to the internet. If you use a hub/switch then the
    boxes on that subnet should have valid external IPs assigned.

    In his original post the OP assigned 3 different IPs in the same local subnet
    so I assumed that represented 1 remote DSL router and 2 NICs on the host. If
    there is only a dsl modem and one NIC then I don't know what the other IP is
    assigned to. Jim, maybe you can clarify this by posting the output of
    ifconfig and describing the physical layout of your LAN.

    >
    > > something else like 192.168.1.0/24. Try this:
    >
    > Yes, this is very important. It must be on a different subnet
    >
    > > DSL modem - 192.168.0.1
    > > inet facing NIC - 192.168.0.2
    > > LAN facing NIC - 192.168.1.1
    > > LAN Client - 192.168.1.2
    > >
    > > Make sure masquerading and IP forwarding are up. You'll need to configure
    > > your routing table too, setting your default gateway to 192.168.0.2. I'm
    > > not
    >
    > No, the default gateway should be 192.168.1.1, the address of the LAN
    > facing NIC.

    That's correct for the clients on the LAN, but the host acting as a router
    needs to have the default route set to the internet facing device. Otherwise
    that host/router will send all non-local traffic back to the LAN. I'd post an
    example from my firewall but it's a lot different configuration and would
    only confuse the issue.

    >
    > > reached the end of my usefulness (at least for today, although I fear
    > > permanent obsolescence is approaching faster than I care to admit).
    >
    > Is that a funny way of saying you are getting older?

    Yup, fraid so.

    Jeff

    -- 
    Check the headers for your unsubscription address
    For additional commands send e-mail to suse-linux-e-help@suse.com
    Also check the archives at http://lists.suse.com
    Please read the FAQs: suse-linux-e-faq@suse.com
    

  • Next message: James Knott: "Re: [SLE] SLSE 9 Do I have to buy the package???"

    Relevant Pages

    • Re: How expand domain subnet?
      ... But if my LAN was going to contain less than 200 Ethernet nodes, ... subnet would reduce the number of possible clients to 62. ... Add a new segment. ... and VPN clients (managed by PIX firewall). ...
      (microsoft.public.windows.server.networking)
    • Re: SBS and 2 NICs
      ... 192.168.200.x for the internal subnet and never had an issue. ... modem should have both a WAN and LAN IP address listed. ... Your Private NIC should be connected to a switch -- the same switch all ... DSL Modem 63.224.85.150 ...
      (microsoft.public.windows.server.sbs)
    • Re: LAN RAS setup guide?
      ... due to you having a single subnet LAN that does not already have a LAN ... Router making the Routing Decisions which leave your Firewall as the Default ...
      (microsoft.public.windows.server.networking)
    • Re: Firewall where internal hosts have non-reserved IPs?
      ... I know I made it sound like the private IP ... >> firewall routes to this subnet. ... > way they're going to give our rather small LAN a whole subnet, ... The least disruptive way to do this is give the LAN side of the firewall ...
      (comp.os.linux.security)
    • Re: SBS and 2 NICs
      ... 192.168.200.x for the internal subnet and never had an issue. ... modem should have both a WAN and LAN IP address listed. ... Your Private NIC should be connected to a switch -- the same switch all ... DSL Modem 63.224.85.150 ...
      (microsoft.public.windows.server.sbs)