Re: [SLE] it's weird: My ndiswrapper can be loaded but ping does not work

Liebe Schneider,

Thank you very much for your answer.

Here is what happens on my SuSE10.1
-----

suse5:~ # route -n

Kernel IP routing table

Destination Gateway Genmask Flags Metric Ref Use Iface

192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo

0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0

suse5:~ #

------
My internal LAN has 192.168.1.0 as the network number.
the ADSL GateWay (router+modem) is the 192.168.1.1

Please tell me, how should the default route should be. How should I configure the default route?

Thank you very much.

Ken Schneider wrote:

On Sun, 2006-07-30 at 18:17 +0700, Patrix Bumi wrote:


Hi friends,

I use OpenSuSE 10.1 , LinkSys WMP54G PCI (Wireless-G PCI Adapter) and LinkSys Wireless-G ADSL Gateway (IP: 192.168.1.1).

Because I can't find the Linux device driver for my WMP54G, I use ndiswrapper.

My ndiswrapper has been installed successfully.
and I did :
1. copied the its windows device driver into "/root" ( Rt61.INF , rt61.cat , rt61.sys )
2. ndiswrapper -i /root/Rt61.INF
3. ndiswrapper -l
driver present, hardware present
4. modprobe ndiswrapper
5. and finally configure the wlan0 with yast2 (network device) as follows:
- I chosed "wireless" as device type
- Configuration name "0" it results wlan0
- Hardware configuration name: static-0
- Module name : ndiswrapper
- IRQ : I left it blank
- Operating mode : managed
- network name (SSID) : linksys
- Encryption : Open / disabled
- IP : 192.168.1.140 / 255.255.255.0
- gateway : 192.168.1.1

My KNetwork-Manager says that my Linksys WMP54G PCI is connected to 'linksys' and active. but if I do:
"ping 192.168.1.1" than I get negative result. And of course I can not go to internet with my WLAN Adapter Card.

the SuSEfirewall2 is stopped.

It's weird for me.

Please help me. Tell me where my mistake.

Thank you very much.




What is the result of route -n? Perhaps the default route is not being
set.





--
Check the headers for your unsubscription address
For additional commands send e-mail to suse-linux-e-help@xxxxxxxx
Also check the archives at http://lists.suse.com
Please read the FAQs: suse-linux-e-faq@xxxxxxxx

Relevant Pages

  • Re: VPN and remote gateway
    ... > It seems you use the wrong route add command. ... > when the VPN connection is established. ... > | using the remote network as my gateway. ...
    (microsoft.public.windows.server.sbs)
  • Re: Persistent Route ignored on W2K when destination network is unavailable
    ... a global setting like the gateway to a particular subnet should be set ... this network access the internet via a NAT firewall (connected to ... via a WAN link. ... route on the Cisco firewall so that any traffic to the internet gets ...
    (microsoft.public.win2000.networking)
  • Re: still no Internet access with wireless suse 10.1
    ... I have used ndiswrapper from the dvd of suse10.1. ... made wlan0 up and eth0 down however the only way I can get on the ... however using a console I added default ip address and route after not being able to connect. ... connection, the default is closed. ...
    (alt.os.linux.suse)
  • Re: How to *ENABLE* icmp redirect on windows xp workstation ?
    ... > I'm using DHCP on the LAN and point default gateway to the internat ... > and the internet gateway forward the packet to innernet gateway. ... it sounds like a static route configured in your ...
    (microsoft.public.windows.server.networking)
  • Re: 1 NIC Windows 2003 Domain; 1 Wireless NIC to Internet - Cant get both working
    ... >and also needs to use a Wireless NIC to connect to the Internet ... Each connection can specify a default gateway, ... and ittue the command 'route print' when both are ...
    (microsoft.public.windowsxp.network_web)