Re: [opensuse] How to hear Amarok playing

Johnny Ernst Nielsen wrote:
Onsdag 28 marts 2007 19:55 kvad A. den Oudsten:

Kai Ponte wrote:

On Tuesday 27 March 2007 08:32:45 am A. den Oudsten wrote:

I'm using 10.2 and want to listen to music.
Playing Amarok I see the music played but don't hear anything
In YaST2 I see KT266 onboard audio is the default.
The volume for CD is 67 and for PCspeakers 53.
What else should I do to hear music?

I'm assuming you can hear other sounds - system and whatnot.

Since I use KDE, I'll forward that solution.

Go to Geeko > Multimedia > Volume Control (KMix)

This will bring up your mixer application. Check to make sure all
your outputs are enabled (light green as opposed to dark green)
and that the volumes are turned up.

Assuming this is all well and good, then open Amarok and go to
Settings > Configure Amarok.

Click on the Engine Icon. For your sound System drop down make
sure you have something selected. I have Xine, but you can use
others. For the Output plugin, if Autodetect doesn't work for
you, select the appropriate plugin - alsa or oss.

If this all doesn't work, then you need to go into YaST and check
your sound settings there. We can revisit if needed.

Tried all you suggested, with no results.
In Yast I see still KT266 onboardsound is default and the driver is
snd-via82xx.

Any other sugestions?


Have you tried checking all your hardware connections and physical settings, as I suggested?

Best regards :o)

Johnny :o)
Yes I did. I even checked it in XP, and it all worked well.

Thanks,


André den Oudsten
--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx

Relevant Pages

  • Re: [opensuse] How to hear Amarok playing
    ... In YaST2 I see KT266 onboard audio is the default. ... Assuming this is all well and good, then open Amarok and go to ... Settings> Configure Amarok. ... In Yast I see still KT266 onboardsound is default and the driver is ...
    (SuSE)
  • Re: [opensuse] How to hear Amarok playing
    ... In YaST2 I see KT266 onboard audio is the default. ... Assuming this is all well and good, then open Amarok and go to Settings> Configure Amarok. ... For the Output plugin, if Autodetect doesn't work for you, select the appropriate plugin - alsa or oss. ... then you need to go into YaST and check your sound settings there. ...
    (SuSE)
  • Re: [SLE] Installation Source in Yast / Not detecting more recent packages from Gurus site
    ... > I recently decided to add Guru's site to my list of sites to look for RPMs ... > for SuSE 9.3. ... I knew I wanted to updated from amarok 1.2.2 to ... Do you have "Refresh" on in the YaST for that Guru repository? ...
    (SuSE)
  • Re: [SLE] Installation Source in Yast / Not detecting more recent packages from Gurus site
    ... I knew I wanted to updated from amarok ... > Do you have "Refresh" on in the YaST for that Guru repository? ... I did a manual refresh and still only came up ... I ended up simply downloading the rpms and installing locally. ...
    (SuSE)
  • Re: [SLE] amarok
    ... > i have installed the new amarok. ... > now it says i must do the engine setup.i have looked at the setup,and ... > all the settings for helix seem to point to the correct dirs,for ... Also check the archives at http://lists.suse.com ...
    (SuSE)