Re: [opensuse] Installing opensuse 11.1 on a soekris net 5501-70

Il mercoledì 17 giugno 2009 10:28:57 Per Jessen ha scritto:
Claudio M. wrote:
Il mercoledì 17 giugno 2009 09:45:18 Per Jessen ha scritto:
I think you need to use /dev/sda instead of /dev/hda.

this was my first attempt

Bye

Well, in openSUSE all non-SCSI storage devices are accessed via some
form of emulation, so your CF drive will almost certainly appear as
a /dev/sdx device.
No /dev/sdx are present.

Are the right drivers being loaded? Are the right drivers in your
initrd? I guess you can't show us thee dmesg output -
Yes, i can :)

Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.7-9-default (geeko@buildhost) (gcc version 4.3.2
[gcc-4_3-branch revision 141291] (SUSE 0
PAT not supported by CPU.
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI not present or invalid.
last_pfn = 0x20000 max_arch_pfn = 0x100000
RAMDISK: 1fa6a000 - 1ffeff80
ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080609]
ACPI: no DMI BIOS year, acpi=force is required to enable ACPI
ACPI: Disabling ACPI support
0MB HIGHMEM available.
512MB LOWMEM available.
mapped low ram: 0 - 20000000
low ram: 00000000 - 20000000
bootmap 00002000 - 00006000
(9 early reservations) ==> bootmem [0000000000 - 0020000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 00006509dc] TEXT DATA BSS ==> [0000100000 - 00006509dc]
#4 [001fa6a000 - 001ffeff80] RAMDISK ==> [001fa6a000 - 001ffeff80]
#5 [0000651000 - 0000654000] INIT_PG_TABLE ==> [0000651000 - 0000654000]
#6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
#8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00020000
HighMem 0x00020000 -> 0x00020000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x00020000
Using APIC driver default
SMP: Allowing 1 CPUs, 0 hotplug CPUs
No local APIC present or hardware disabled
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 30000000 (gap: 20000000:dff00000)
PERCPU: Allocating 39068 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129823
Kernel command line: root=/dev/sda1 showopts console=ttyS0,19200,8n1
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
TSC: Using PIT calibration value
Detected 499.896 MHz processor.
Console: colour dummy device 80x25
console [ttyS0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 507524k/524288k available (2342k kernel code, 16208k reserved, 1960k
data, 316k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffdf6000 - 0xfffff000 (2084 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xe0800000 - 0xff3fe000 ( 491 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
.init : 0xc053a000 - 0xc0589000 ( 316 kB)
.data : 0xc034988b - 0xc0533a90 (1960 kB)
.text : 0xc0100000 - 0xc034988b (2342 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Calibrating delay loop (skipped), value calculated using timer frequency..
999.79 BogoMIPS (lpj=1999584)
kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights
Reserved
kdb_cmd[0]: defcmd archkdb "" "First line arch debugging"
kdb_cmd[7]: defcmd archkdbcpu "" "archkdb with only tasks on cpus"
kdb_cmd[14]: defcmd archkdbshort "" "archkdb with less detailed backtrace"
kdb_cmd[21]: defcmd archkdbcommon "" "Common arch debugging"
Security Framework initialized
SELinux: Disabled at boot.
AppArmor: AppArmor initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
weird, boot CPU (#0) not listedby the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (999.79 BogoMIPS).
net_namespace: 1044 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.01 entry at 0xfac61, last bus=0
PCI: Using configuration type 1 for base access
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: PnP BIOS support was not detected.
PCI: Probing PCI hardware
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:08.0: PME# disabled
pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:14.0: BAR 1: can't allocate resource
pci 0000:00:14.0: BAR 2: can't allocate resource
AppArmor: AppArmor Filesystem Enabled
ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread DF420CC0 could not
acquire Mutex [1] [20080609]
pci 0000:00:14.0: BAR 2: error updating (0x001001 != 0x006201)
pci 0000:00:14.0: BAR 1: error updating (0x001401 != 0x006101)
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 5655k freed
platform rtc_cmos: registered platform RTC device (no PNP device found)
audit: initializing netlink socket (disabled)
type=2000 audit(3484388428.066:1): initialized
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 250
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver8 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Clocksource tsc unstable (delta = 360031852 ns)
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 316k freed
Write protecting the kernel text: 2344k
Write protecting the kernel read-only data: 1768k
doing fast boot
your system time is not correct:
Tue Apr 25 07:12:13 UTC 1944
setting system time to:
Tue Dec 2 00:00:00 UTC 2008
SCSI subsystem initialized
FATAL: Error inserting processor
(/lib/modules/2.6.27.7-9-default/kernel/drivers/acpi/processor.ko): No such t
ice
WARNING: Error inserting processor
(/lib/modules/2.6.27.7-9-default/kernel/drivers/acpi/processor.ko): No suce
FATAL: Error inserting thermal
(/lib/modules/2.6.27.7-9-default/kernel/drivers/acpi/thermal.ko): Unknown
symb)
Uniform Multi-Platform E-IDE driver
FATAL: Error inserting fan
(/lib/modules/2.6.27.7-9-default/kernel/drivers/acpi/fan.ko): No such device
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
udevd version 128 startedh udev

ohci_hcd 0000:00:15.0: OHCI Host Controller
ohci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:15.0: irq 15, io mem 0xa0005000
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not
after
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb1: SerialNumber: 0000:00:15.0
ehci_hcd 0000:00:15.1: EHCI Host Controller
ehci_hcd 0000:00:15.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:15.1: irq 15, io mem 0xa0006000
ehci_hcd 0000:00:15.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-9-default ehci_hcd
usb usb2: SerialNumber: 0000:00:15.1
Boot logging started on /dev/ttyS0(/dev/console) at Tue Dec 2 00:00:04 2008
resume device not found (ignoring)
Waiting for device /dev/sda1 to appear: ..............................Could
not find /dev/sda1.


hmm. I think the problem is that the drivers needed for your CF card
aren't being loaded.
I think this too, but i don't know wich driver

Thanks for the help

Bye

Claudio
--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx

Relevant Pages
Loading