Re: Wireless device appears to be configured properly but I cannot ping my router!

Pete Holsberg wrote:
I installed the proper drivers using ndiswrapper and then used Network
Tools (Ubuntu 7.04) to set the device up.

It sees my WAP and the configuration via Network Tools appears to be
correct.

However, I cannot ping anything ("cannot reach") and iwconfig reports:

wlan0 IEEE 802.11b ESSID:off/any
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
Bit Rate=1 Mb/s Sensitivity=-200 dBm
RTS thr=2346 B Fragment thr=2346 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

What have I missed?

Thanks.

It appears to me from your iwconfig that the wireless card did not
locate your ESSID and Access Point.

Did you verify that the ndiswrapper is setup properly?
sudo ndiswrapper -l

Did you restart your network?
sudo /etc/init.d/networking/ restart

Do I recall correctly that you have a Ralink 2500 chipset?
I have never used that chipset but unless you have newer/better info,
the website I posted says:

"Now because Ubuntu Feisty is using an applet called Network Manager and
considering that it does not work with any Ralink based chipsets, you
might as well kick it to the curb. You can safely uninstall it without
any hassles.

Goto System, Administration and select Synaptic. You can use this tool
to remove network-manager. If you are unfamiliar with Synaptic, use this
tute <https://help.ubuntu.com/community/SynapticHowto> for assistance.

After removing Network-Manager, you should use Synaptic again to install
a program called wifi-radar. Once this is installed, now you will want
to download this zip file
<http://www.computertroubleshoot.com/lg/wireless.zip>."



I do not know enough about the network tools to understand how to use
them to set up a wireless network.

HTH
Jerry




--
ubuntu-users mailing list
ubuntu-users@xxxxxxxxxxxxxxxx
Modify settings or unsubscribe at: https://lists.ubuntu.com/mailman/listinfo/ubuntu-users

Relevant Pages

  • Wireless device appears to be configured properly but I cannot ping my router!
    ... I installed the proper drivers using ndiswrapper and then used Network ... Tools (Ubuntu 7.04) to set the device up. ... It sees my WAP and the configuration via Network Tools appears to be ... Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 ...
    (Ubuntu)
  • Re: [RFC][PATCH 1/1] cxgb3i: cxgb3 iSCSI initiator
    ... > based on reading the source that this driver uses "TCP port stealing" ... I don't think the right answer for iSCSI offload ... Maybe we could somehow hook into the existing network tools so they support these iscsi hbas as well as normal NICs. ...
    (Linux-Kernel)
  • Re: Wireless device appears to be configured properly but I cannot ping my router!
    ... Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 ... Did you verify that the ndiswrapper is setup properly? ... I do not know enough about the network tools to understand how to use ...
    (Ubuntu)
  • Lost Networking in Win 2000
    ... Network and Dial-up Connection Window. ... I have tried almost everything including re-installing ...
    (microsoft.public.win2000.networking)
  • Re: New User- Network Problem
    ... network settings & network tools devices. ... I'm just connecting through eth1 my PCI 1G network card. ... In Network tools device eth0 and eth1 are both disabled! ...
    (Debian-User)