Re: Intel PRO/1000CTcontroller & SuSE Pro 8.2 (MSI 875P Neo-FIS2R)

From: SuSE_Fan (SuSE_Fan_at_)
Date: 08/02/03 

Date: Sat, 02 Aug 2003 22:13:15 +0800

I'm not sure whether or not 8.2 contains the e1000 module - installing
SuSE 8.2 fresh does not detect the integrated controller.

The status remains the same whether or not I compile and install the
driver separately.

I know the controller works because booting XP I use it to connect to
the net via ADSL.

I have attached below a copy of my bootmsg...eth0 initialisation fails
:(

Inspecting /boot/System.map-2.4.20-64GB-SMP
Loaded 21295 symbols from /boot/System.map-2.4.20-64GB-SMP.
Symbols match kernel version 2.4.20.
Loaded 148 symbols from 11 modules.
klogd 1.4.1, log source = ksyslog started.
<4>Linux version 2.4.20-64GB-SMP (root@SMP_X86.suse.de) (gcc version
3.3 20030226 (prerelease) (SuSE Linux)) #1 SMP Mon Mar 17 17:56:03 UTC
2003
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
<4> BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
<4> BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
<4> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
<4>Scanning bios EBDA for MXT signature
<5>127MB HIGHMEM available.
<5>896MB LOWMEM available.
<7>ACPI: have wakeup address 0xc0002000
<4>found SMP MP-table at 000fb8a0
<4>hm, page 000fb000 reserved twice.
<4>hm, page 000fc000 reserved twice.
<4>hm, page 000f5000 reserved twice.
<4>hm, page 000f6000 reserved twice.
<4>On node 0 totalpages: 262128
<4>zone(0): 4096 pages.
<4>zone(1): 225280 pages.
<4>zone(2): 32752 pages.
<6>ACPI: RSDP (v000 AMI ) @ 0x000f9dd0
<6>ACPI: RSDT (v001 AMIINT INTEL875 00000.00016) @ 0x3fff0000
<6>ACPI: FADT (v001 AMIINT INTEL875 00000.00017) @ 0x3fff0030
<6>ACPI: MADT (v001 AMIINT INTEL875 00000.00009) @ 0x3fff00c0
<6>ACPI: DSDT (v001 INTEL I875 00000.04096) @ 0x00000000
<5>ACPI: BIOS passes blacklist
<6>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>Processor #0 Pentium 4(tm) XEON(tm) APIC version 16
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
<4>Processor #1 Pentium 4(tm) XEON(tm) APIC version 16
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
<6>IOAPIC[0]: Assigned apic_id 2
<4>IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, IRQ 0-23
<6>ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0]
trigger[0x0])
<6>ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1]
trigger[0x3])
<6>Using ACPI (MADT) for SMP configuration information
<4>Building zonelist for node : 0
<4>Kernel command line: auto BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent
<6>Initializing CPU#0
<4>Detected 2636.994 MHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 5255.98 BogoMIPS
<6>Memory: 1023440k/1048512k available (1854k kernel code, 16364k
reserved, 592k data, 184k init, 131008k highmem)
<6>Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
<6>Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
<4>Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
<4>per-CPU timeslice cutoff: 1463.30 usecs.
<4>task migration cache decay timeout: 10 msecs.
<4>enabled ExtINT on CPU#0
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Booting processor 1/1 eip 3000
<6>Initializing CPU#1
<4>masked ExtINT on CPU#1
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Calibrating delay loop... 5269.09 BogoMIPS
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#1.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
<6>Total of 2 processors activated (10525.08 BogoMIPS).
<4>cpu_sibling_map[0] = 1
<4>cpu_sibling_map[1] = 0
<4>ENABLING IO-APIC IRQs
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21,
2-22, 2-23 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<7>number of MP IRQ sources: 16.
<7>number of IO-APIC #2 registers: 24.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>....... : physical APIC id: 02
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 00178020
<7>....... : arbitration: 00
<4>An unexpected IO-APIC was found. If this kernel release is less
than
<4>three months old please report this to linux-smp@vger.kernel.org
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 003 03 0 0 0 0 0 1 1 39
<7> 02 003 03 0 0 0 0 0 1 1 31
<7> 03 003 03 0 0 0 0 0 1 1 41
<7> 04 003 03 0 0 0 0 0 1 1 49
<7> 05 003 03 0 0 0 0 0 1 1 51
<7> 06 003 03 0 0 0 0 0 1 1 59
<7> 07 003 03 0 0 0 0 0 1 1 61
<7> 08 003 03 0 0 0 0 0 1 1 69
<7> 09 003 03 1 1 0 0 0 1 1 71
<7> 0a 003 03 0 0 0 0 0 1 1 79
<7> 0b 003 03 0 0 0 0 0 1 1 81
<7> 0c 003 03 0 0 0 0 0 1 1 89
<7> 0d 003 03 0 0 0 0 0 1 1 91
<7> 0e 003 03 0 0 0 0 0 1 1 99
<7> 0f 003 03 0 0 0 0 0 1 1 A1
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 2636.9451 MHz.
<4>..... host bus clock speed is 202.8417 MHz.
<4>cpu: 0, clocks: 2028417, slice: 676139
<4>CPU0<T0:2028416,T1:1352272,D:5,S:676139,C:2028417>
<4>cpu: 1, clocks: 2028417, slice: 676139
<4>CPU1<T0:2028416,T1:676128,D:10,S:676139,C:2028417>
<4>checking TSC synchronization across CPUs: passed.
<4>migration_task 0 on cpu=0
<4>migration_task 1 on cpu=1
<6>ACPI: Subsystem revision 20030228
<6>PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=3
<6>PCI: Using configuration type 1
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
<4> ACPI-1121: *** Error: Method execution failed [\_SB_.PCI0.MDET]
(Node f7508a00), AE_AML_REGION_LIMIT
<4> ACPI-1121: *** Error: Method execution failed [\_SB_.PCI0._CRS]
(Node f7508b00), AE_AML_REGION_LIMIT
<4> ACPI-0098: *** Error: Method execution failed [\_SB_.PCI0._CRS]
(Node f7508b00), AE_AML_REGION_LIMIT
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
<4>Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT]
<6>ACPI: Power Resource [URP1] (off)
<6>ACPI: Power Resource [URP2] (off)
<6>ACPI: Power Resource [FDDP] (off)
<6>ACPI: Power Resource [LPTP] (off)
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15,
disabled)
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15,
disabled)
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 *12 14 15)
<6>PCI: Probing PCI hardware
<4>ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
<4>ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
<7>IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18)
<7>00:00:1f[A] -> 2-18 -> IRQ 18
<7>IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17)
<7>00:00:1f[B] -> 2-17 -> IRQ 17
<7>IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16)
<7>00:00:1d[A] -> 2-16 -> IRQ 16
<7>IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19)
<7>00:00:1d[B] -> 2-19 -> IRQ 19
<7>Pin 2-18 already programmed
<7>IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23)
<7>00:00:1d[D] -> 2-23 -> IRQ 23
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-16 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-16 already programmed
<7>IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21)
<7>00:03:09[A] -> 2-21 -> IRQ 21
<7>IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22)
<7>00:03:0e[A] -> 2-22 -> IRQ 22
<7>IOAPIC[0]: Set PCI routing entry (2-20 -> 0xe1 -> IRQ 20)
<7>00:03:08[A] -> 2-20 -> IRQ 20
<6>PCI: Using ACPI for IRQ routing
<6>PCI: if you experience problems, try using option 'pci=noacpi' or
even 'acpi=off'
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
<5>apm: disabled - APM is not SMP safe.
<4>mxt_scan_bios: enter
<4>Starting kswapd
<4>bigpage subsystem: allocated 0 bigpages (=0MB).
<4>allocated 32 pages and 32 bhs reserved for the highmem bounces
<4>kinoded started
<5>VFS: Disk quotas vdquot_6.5.1
<5>aio_setup: num_physpages = 65532
<5>aio_setup: sizeof(struct page) = 48
<6>Detected PS/2 Mouse Port.
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS
MULTIPORT SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>Real Time Clock Driver v1.10e
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024
blocksize
<6>loop: loaded (max 16 devices)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
<6>C-ICH: IDE controller at PCI slot 00:1f.1
<4>PCI: Enabling device 00:1f.1 (0005 -> 0007)
<6>C-ICH: chipset revision 2
<6>C-ICH: not 100%% native mode: will probe irqs later
<6> ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
<6> ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
<4>hda: Maxtor 6E040L0, ATA DISK drive
<4>hdb: ST330620A, ATA DISK drive
<4>blk: queue c04410a0, I/O limit 4095Mb (mask 0xffffffff)
<4>blk: queue c04411fc, I/O limit 4095Mb (mask 0xffffffff)
<4>hdc: ATAPI CD-RW 52XMax, ATAPI CD/DVD-ROM drive
<4>hdd: QUANTUM FIREBALL CR13.0A, ATA DISK drive
<4>blk: queue c0441690, I/O limit 4095Mb (mask 0xffffffff)
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=4998/255/63,
UDMA(100)
<4>hdb: attached ide-disk driver.
<6>hdb: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=3649/255/63,
UDMA(100)
<4>hdd: attached ide-disk driver.
<4>hdd: host protected area => 1
<6>hdd: 25429824 sectors (13020 MB) w/418KiB Cache, CHS=25228/16/63,
UDMA(33)
<4>ide-floppy driver 0.99.newide
<6>Partition check:
<6> hda: hda1 hda2 hda3
<6> hdb: hdb1 hdb2 < hdb5 >
<6> hdd:<6> [PTBL] [1582/255/63] hdd1 hdd2 < hdd5 >
<4>ide-floppy driver 0.99.newide
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno =
2
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 8192 buckets, 64Kbytes
<6>TCP: Hash tables configured (established 262144 bind 65536)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 479k freed
<4>VFS: Mounted root (ext2 filesystem).
<6>scsi0 : AdvanSys SCSI 3.3G: PCI Ultra: IO 0xCC00-0xCC0F, IRQ 0x11
<4> Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>reiserfs: found format "3.6" with standard journal
<4>reiserfs: enabling write barrier flush mode
<4>reiserfs: using ordered data mode
<4>reiserfs: checking transaction log (ide0(3,3)) for (ide0(3,3))
<4>Using r5 hash to sort names
<4>VFS: Mounted root (reiserfs filesystem) readonly.
<5>Trying to move old root to /initrd ... failed
<5>Unmounting old root
<5>Trying to free ramdisk memory ... okay
<6>Freeing unused kernel memory: 184k freed
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>LVM version 1.0.5+(mp-v6a)(22/07/2002) module loaded
<6>Adding Swap: 1052248k swap-space (priority 42)
<6>NTFS driver 2.1.1a [Flags: R/O MODULE].
<6>NTFS volume version 3.1.
<4>MSDOS FS: IO charset iso8859-1
<4>MSDOS FS: IO charset iso8859-1
<4>MSDOS FS: IO charset iso8859-1
<4>MSDOS FS: IO charset iso8859-1
<4>hdc: attached ide-cdrom driver.
<4>hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
<6>Uniform CD-ROM driver Revision: 3.12
<6>scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sun Aug 3 04:09:15
2003

Configuring serial ports...

ttyS0 at 0x03f8 (irq = 4) is a 16550A

ttyS1 at 0x02f8 (irq = 3) is a 16550A

modprobe: modprobe: Can't locate module char-major-212

Configured serial ports

doneRun file system check on root for LVM activation

doneRemounting root file system (/) read/write for vgscan...

Scanning for LVM volume groups...

vgscan -- reading all physical volumes (this may take a while...)

vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created

vgscan -- WARNING: This program does not do a VGDA backup of your
volume group

Activating LVM volume groups...

vgchange -- no volume groups found

done

Activating swap-devices in /etc/fstab...

doneChecking file systems...

fsck 1.28 (31-Aug-2002)

Reiserfs super block in block 16 on 0x303 of format 3.6 with standard
journal

Blocks (total/free): 4755240/4250894 by 4096 bytes

Filesystem is clean

doneMounting local file systems...

proc on /proc type proc (rw)

devpts on /dev/pts type devpts (rw,mode=0620,gid=5)

/dev/hda1 on /windows/C type ntfs
(ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=iso8859-1)

/dev/hdb1 on /windows/D type vfat
(rw,noexec,nosuid,nodev,gid=100,umask=0002,iocharset=iso8859-1,code=437)

/dev/hdd1 on /windows/E type vfat
(rw,noexec,nosuid,nodev,gid=100,umask=0002,iocharset=iso8859-1,code=437)

/dev/hdb5 on /windows/F type vfat
(rw,noexec,nosuid,nodev,gid=100,umask=0002,iocharset=iso8859-1,code=437)

/dev/hdd5 on /windows/G type vfat
(rw,noexec,nosuid,nodev,gid=100,umask=0002,iocharset=iso8859-1,code=437)

doneLoading required kernel modules

doneRestore device permissions
done

Activating remaining swap-devices in /etc/fstab...

doneMounting shared memory FS on /dev/shm
done

Setting up the CMOS clock
done

Setting up timezone data
done

Setting up hostname 'linux'
done

Setting up loopback interface
done

Enabling syn flood protection
done

Disabling IP forwarding
done

Creating /var/log/boot.msg

done<notice>killproc: kill(34,29)
Running /etc/init.d/boot.local

Boot logging started on /dev/tty1(/dev/console) at Sat Aug 2 20:09:22
2003

Master Resource Control: previous runlevel: N, switching to runlevel:
5

Starting Firewall Initialization (phase 1 of 3)
done<notice>killproc: kill(34,3)

INIT: Entering runlevel: 5

<notice>/etc/init.d/rc5.d/S01SuSEfirewall2_init start

done

<notice>'/etc/init.d/rc5.d/S01SuSEfirewall2_init start' exits with
status 0
<notice>/etc/init.d/rc5.d/S01isdn start
<notice>Initializing random number generator'/etc/init.d/rc5.d/S01isdn
start' exits with status 0
<notice>/etc/init.d/rc5.d/S01random start

done

<notice>'/etc/init.d/rc5.d/S01random start' exits with status 0
<notice>/etc/init.d/rc5.d/S05network start
Setting up network interfaces:

    lo
done

    eth0
failed

    dsl0
manual

Starting syslog services<notice>'/etc/init.d/rc5.d/S05network start'
exits with status 0
<notice>/etc/init.d/rc5.d/S06syslog start
<notice>startproc: execve (/sbin/syslogd) [ /sbin/syslogd ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=21
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/sbin/syslogd ]

done

<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -2 ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=21
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/sbin/klogd ]
<notice>'/etc/init.d/rc5.d/S06syslog start' exits with status 0
<notice>/etc/init.d/rc5.d/S07hotplug start
Starting hotplugging services [ ieee1394 net pci usb .... ]
done

<notice>'/etc/init.d/rc5.d/S07hotplug start' exits with status 0
<notice>/etc/init.d/rc5.d/S08resmgr start
Starting resource manager<notice>startproc: execve (/sbin/resmgrd) [
/sbin/resmgrd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh
progress=23 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES
COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin
RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2
BOOT_IMAGE="SuSE_8.2_Prof root=303 hdc=ide-scsi hdclun=0 splash=silent
showopts splash=silent sscripts=40 _=/sbin/startproc
DAEMON=/sbin/resmgrd ]

done

Starting Firewall Initialization (phase 2 of 3)
<notice>'/etc/init.d/rc5.d/S08resmgr start' exits with status 0
<notice>/etc/init.d/rc5.d/S09SuSEfirewall2_setup start

done

Starting RPC portmap
daemon<notice>'/etc/init.d/rc5.d/S09SuSEfirewall2_setup start' exits
with status 0
<notice>/etc/init.d/rc5.d/S09portmap start
<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=25
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/sbin/portmap ]

done

<notice>'/etc/init.d/rc5.d/S09portmap start' exits with status 0
<notice>/etc/init.d/rc5.d/S09splash_early start
<notice>'/etc/init.d/rc5.d/S09splash_early start' exits with status 0
<notice>/etc/init.d/rc5.d/S11SuSEfirewall2_final start
Starting Firewall Initialization (phase 3 of 3)
done

<notice>'/etc/init.d/rc5.d/S11SuSEfirewall2_final start' exits with
status 0
<notice>/etc/init.d/rc5.d/S13alsasound start
Starting sound driver: intel8x0
done

Restoring the previous sound setting
done

<notice>'/etc/init.d/rc5.d/S13alsasound start' exits with status 0
<notice>/etc/init.d/rc5.d/S13fbset start
<notice>'/etc/init.d/rc5.d/S13fbset start' exits with status 0
<notice>/etc/init.d/rc5.d/S13rpmconfigcheck start
Starting SMPPPD<notice>'/etc/init.d/rc5.d/S13rpmconfigcheck start'
exits with status 0
<notice>/etc/init.d/rc5.d/S13smpppd start
<notice>startproc: execve (/usr/sbin/smpppd) [ /usr/sbin/smpppd ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=31
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/usr/sbin/smpppd ]

done

<notice>'/etc/init.d/rc5.d/S13smpppd start' exits with status 0
<notice>/etc/init.d/rc5.d/S13sshd start
Starting SSH daemon<notice>startproc: execve (/usr/sbin/sshd) [
/usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=32
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/usr/sbin/sshd ]

done

<notice>'/etc/init.d/rc5.d/S13sshd start' exits with status 0
<notice>/etc/init.d/rc5.d/S14kbd start
Loading keymap qwerty/us.map.gz

doneLoading compose table winkeys shiftctrl latin1.add
done

Loading console font lat1-16.psfu

doneLoading screenmap none

doneSetting up console ttys

done<notice>'/etc/init.d/rc5.d/S14kbd start' exits with status 0
<notice>/etc/init.d/rc5.d/S14postfix start
Starting mail service (Postfix)
done

Starting service at daemon
done

Starting CRON daemon<notice>'/etc/init.d/rc5.d/S14postfix start' exits
with status 0
<notice>/etc/init.d/rc5.d/S14splash start
<notice>'/etc/init.d/rc5.d/S14splash start' exits with status 5
<notice>/etc/init.d/rc5.d/S15atd start
<notice>startproc: execve (/usr/sbin/atd) [ /usr/sbin/atd ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=36
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/usr/sbin/atd ]
<notice>'/etc/init.d/rc5.d/S15atd start' exits with status 0
<notice>/etc/init.d/rc5.d/S15cron start
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=37
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/usr/sbin/cron ]

done

Starting hardware scan on boot<notice>'/etc/init.d/rc5.d/S15cron
start' exits with status 0
<notice>/etc/init.d/rc5.d/S15hwscan start
<notice>Starting Name Service Cache Daemon'/etc/init.d/rc5.d/S15hwscan
start' exits with status 0
<notice>/etc/init.d/rc5.d/S15nscd start
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [
CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=39
INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/
PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303
hdc=ide-scsi hdclun=0 splash=silent showopts splash=silent sscripts=40
_=/sbin/startproc DAEMON=/usr/sbin/nscd ]

done

<notice>'/etc/init.d/rc5.d/S15nscd start' exits with status 0
<notice>/etc/init.d/rc5.d/S16splash_late start
<notice>'/etc/init.d/rc5.d/S16splash_late start' exits with status 0
<notice>/etc/init.d/rc5.d/S16xdm start
Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [
/opt/kde3/bin/kdm ], [ LC_MONETARY= CONSOLE=/dev/console TERM=linux
SHELL=/bin/sh LC_NUMERIC= QTDIR=/usr/lib/qt3 LC_ALL= progress=41
INIT_VERSION=sysvinit-2.82 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1
AUTOBOOT=YES COLUMNS=80
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin LC_MESSAGES=
RUNLEVEL=5 LC_COLLATE=POSIX PWD=/ LANG=en_US PREVLEVEL=N LINES=25
HOME=/ SHLVL=2 BOOT_IMAGE="SuSE_8.2_Prof root=303 hdc=ide-scsi
hdclun=0 splash=silent showopts splash=silent no_proxy=localhost
RC_LC_COLLATE=POSIX WINDOWMANAGER=/usr/X11R6/bin/kde PRINTER=lp
RC_LANG=en_US LC_CTYPE=en_US sscripts=40 LC_TIME= _=/sbin/startproc
DAEMON=/opt/kde3/bin/kdm ]

done

Master Resource Control: runlevel 5 has been
reached

Skipped services in runlevel 5: splash

<notice>'/etc/init.d/rc5.d/S16xdm start' exits with status 0
<notice>killproc: kill(337,3)

Relevant Pages