take a lot of time to boot

From: os2 (marcpirat_at_yahoo.com)
Date: 06/06/04 

Date: 6 Jun 2004 09:50:53 -0700

hi

i installed suse 9.1, that took 2 minutes to boot ( i have a 1800+
athlon with 512mb)

with suse 9.0 that took 50 second

my desg file:

dmesg
Linux version 2.6.4-54.5-default (geeko@buildhost) (gcc version 3.3.3
(SuSE Linu
x)) #1 Fri May 7 21:43:10 UTC 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f7f0000 (usable)
 BIOS-e820: 000000001f7f0000 - 000000001f7f8000 (ACPI data)
 BIOS-e820: 000000001f7f8000 - 000000001f800000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
509MB vmalloc/ioremap area available.
0MB HIGHMEM available.
503MB LOWMEM available.
On node 0 totalpages: 129008
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 124912 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @
0x000fa4e0
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @
0x1f7f0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @
0x1f7f0030
ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: local apic disabled
Built 1 zonelists
Kernel command line: root=/dev/hda9 vga=0x314 desktop resume=/dev/sda2
splash=si
lent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
CKRM Initialized
Detected 1534.121 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 506640k/516032k available (1970k kernel code, 8600k reserved,
677k data,
 212k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay loop... 3039.23 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security
failed.
Failure registering capabilities with the kernel
selinux_register_security: Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Looking for DSDT in initrd ...No customized DSDT found in initrd!
Freeing initrd memory: 1311k freed
CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000
00000000
CPU: After vendor identify, caps: 0383f9ff c1c3f9ff 00000000
00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
do_initcalls
init_elf_binfmt
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
No customized DSDT found!
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
 ... the first call_usermodehelper: pci_bus
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using
IRQ 255
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off
'
vesafb: framebuffer at 0xd0000000, mapped to 0xe0006000, size 7104k
vesafb: mode is 800x600x16, linelength=1600, pages=6
vesafb: protected mode interface info at c000:6e42
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Initial HugeTLB pages allocated: 0
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
SELinux: Registering netfilter hooks
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size
27761 bytes
, found (800x600, 11810 bytes, v3).
Console: switching to colour frame buffer device 92x32
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using
IRQ 255
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: MAXTOR 6L040J2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78198750 sectors (40037 MB) w/1819KiB Cache, CHS=65535/16/63,
UDMA(100)
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 8
NET: Registered protocol family 20
Resume Machine: resuming from /dev/sda2
Resuming from device unknown-block(0,0)
Resume Machine: Error -6 resuming
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
sym0: <875> rev 0x26 at pci 0000:00:09.0 irq 11
sym0: Tekram NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18i
  Vendor: SEAGATE Model: ST118202LC Rev: 7D08
  Type: Direct-Access ANSI SCSI revision: 02
sym0:0:0: tagged command queuing enabled, command queue depth 16.
sym0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
SCSI device sda: drive cache: write back
 sda: sda1 < sda5 sda6 > sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: TOSHIBA Model: CD-ROM XM-6401TA Rev: 1001
  Type: CD-ROM ANSI SCSI revision: 02
  Vendor: SAF Model: CD-R4012 Rev: 6.0N
  Type: CD-ROM ANSI SCSI revision: 02
VFS: Mounted root (jfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 212k freed
Adding 361420k swap on /dev/sda2. Priority:42 extents:1
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
subfs 0.9
hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
  http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xd400, 00:07:95:46:91:f3, IRQ 5.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link
45e1.
eth0: Setting full-duplex based on MII #1 link partner capability of
45e1.
NET: Registered protocol family 17
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1, 16 throttling states)
powernow-k8: AMD Athlon 64 or AMD Opteron processor required
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03545c0(lo)
IPv6 over IPv4 tunneling driver
ALSA sound/pci/ac97/ac97_codec.c:1867: AC'97 0 analog subsections not
ready
NET: Registered protocol family 23
powernow: PowerNOW! Technology present. Can scale: nothing.
Disabled Privacy Extensions on device dd982c00(sit0)
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: irq 11, io base 0000d800
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.4-54.5-default uhci_hcd
usb usb1: SerialNumber: 0000:00:11.2
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: irq 11, io base 0000dc00
Linux agpgart interface v0.100 (c) Dave Jones
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.4-54.5-default uhci_hcd
usb usb2: SerialNumber: 0000:00:11.3
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:11.4: UHCI Host Controller
uhci_hcd 0000:00:11.4: irq 11, io base 0000e000
uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.4-54.5-default uhci_hcd
usb usb3: SerialNumber: 0000:00:11.4
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
agpgart: Detected VIA PM266/KM266 chipset
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: AGP aperture is 64M @ 0xe0000000
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
sym0: SCSI parity error detected: SCR1=132 DBC=50000000 SBCL=0
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Generic
drivers/usb/core/usb.c: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
sym0: SCSI parity error detected: SCR1=132 DBC=2440a04 SBCL=0
Non-volatile memory driver v1.2
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
sym0: SCSI parity error detected: SCR1=132 DBC=2440a04 SBCL=0
eth0: no IPv6 routers present
sym0:4:0: ABORT operation started.
sym0:4:0: ABORT operation timed-out.
sym0:4:0: DEVICE RESET operation started.
sym0:4:0: DEVICE RESET operation timed-out.
sym0:4:0: BUS RESET operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sym0:4:0: BUS RESET operation complete.
sym0:4: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 16)
sr0: scsi-1 drive
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
sym0:6: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 15)
sr1: scsi-1 drive
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 6, lun 0
st: Version 20040318, fixed bufsize 32768, s/g segs 256
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi0, channel 0, id 4, lun 0, type 5
Attached scsi generic sg2 at scsi0, channel 0, id 6, lun 0, type 5
BIOS EDD facility v0.13 2004-Mar-09, 2 devices found
mtrr: 0xd0000000,0x800000 overlaps existing 0xd0000000,0x400000
sym0: SCSI parity error detected: SCR1=132 DBC=50000000 SBCL=0
sym0:4:0: ABORT operation started.
sym0:4:0: ABORT operation timed-out.
sym0:4:0: DEVICE RESET operation started.
sym0:4:0: DEVICE RESET operation timed-out.
sym0:4:0: BUS RESET operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sym0:4:0: BUS RESET operation complete.

any idea?

thanks 

---
La boîte à prog http://www.laboiteaprog.com