Re: My 3rd sata drive



On 06/07/2010 02:09 PM, J.O. Aho wrote:
nomail@xxxxxxxxxxxxxxx wrote:
On 06/06/2010 01:52 AM, J.O. Aho wrote:

I looked at the manual and it just talks 4 sata connectors which are
numbered 1-4. I don't see any raid connectors as such, raid setup is in
BIOS.

Check that your "sda" is really connected to SATA1, so you haven't just at
some point put it in SATA4 and then changed boot order in BIOS.
This would explain why the booting don't work with your 3 disks setup, you
read the kernel from the machine with the kernel in hd0,0, but the kernel will
see the other disk as /dev/sda and that one does lack your high partition.

I'll check this out, for now i'm busy prepping a eeeeeeeeeeeeeepc :-)

The other idea of reading the dmsg is probably a good one too, not that
I could understand most of it. The question is how to recover it? Every
suspect boot is incomplete by definition and by the time I get a good
one the boot message has been overwritten. Maybe if I boot another
partition the second time with only two disks and then fish out the dmsg
from the first?

Much depends on your distro, some distros do save the dmesg to /var/log/dmesg
and then you can read /var/log/dmesg.X what happen previous times you booted.


I got it as I thought I could, afterwards and from a another booted
system. It's been a loooooooong series of sesssions.

Your hunch that the sata pinouts 1&2/3&4 are somehow separated is
beginning to look like a major suspect. The mobo manual is rather tight
lipped about it. For years I've presumed that they were just that 4 nice
sata drives and as I never had more than two I never ran into any trouble.

Now

1 booted p-9 of disk 320gb-A in pos-1, 320gb-B in pos-2, 500gb in pos-3
"could not find /dev/sda9"

2 booted p-9 of disk 320B in pos-1, nothing in pos-2, 500 in pos-3
"could not find /dev/sda9"

In the above only the 320gb-A driove had a bootable partition #9

Then

3 booted p-9 of 320gb-B in pos-1, nothing in pos-2/3, 2000gb-A in pos-4

I again got

"could not find /dev/sda9"

but the boot continued. Here I got results because I more or less
successfully booted a suse-10.3 partition #9 ...but... on the 4th drive
instead!

fstab swap, fdisk against /dev/sda and such ALL confirmed the
system was in fact on the 4th drive, 2000gb-A.


Grub > root (hd0,14) [from within OS]
"Error 18: selected cyl. not supported by BIOS"
..... not likely with a 320gb drive



Grub > root (hd0,4) [from within OS]
"..fs unknown, partition type 82"
.... that's a swap partition on the 2000gb-A drive


Contrary to what I had presumed, with 'a' kernel booted and grub loaded
within it, the disk numbers given by grub are no longer the bios
numbers. Giving the same arguments to grub before the boot would hit the
correct disk and its partitions. That disk being 320gb and its #5 being
vfat neither of the above errors surface until booted.

All of the above confirms the finding that the 4th drive was being
booted as the 'final' one :-)

I can also boot with a disk in only #3 or only #4 or #3 & #4, there
again the 2/3 border not being crossed.

The only option might be to get another board, one that offers a
straight series 4 or more SATA connectors and no PATA (just guessing if
there are such boards).


=======================================================
I then fished out the message. Looks like if a same-number bootable
partition on the other side of 1&2 exists then it will boot instead. A
kernel/modules conflict then arises and I'm only guessing that this may
be because the target kernel has loaded but is now somewhere else and
can't find the matching modules sets (?).

.....a few long bits cut...


Cannot find map file.
No module symbols loaded - kernel modules not enabled.

Cannot build symbol table - disabling symbol lookups
klogd 1.4.1, log source = ksyslog started.
<6>Initializing cgroup subsys cpuset
<6>Initializing cgroup subsys cpu
<5>Linux version 2.6.27.39-0.2-default (geeko@buildhost) (gcc version
4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2009-11-23
12:57:38 +0100
<6>BIOS-provided physical RAM map:
<6> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
<6> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
<6> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<6> BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
<6> BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
<6> BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
<6> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
<6> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
<6>DMI 2.3 present.
<5>Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
<6>last_pfn = 0x7fff0 max_arch_pfn = 0x100000
<6>x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
<7>kernel direct mapping tables up to 38000000 @ 10000-15000
<6>RAMDISK: 37a14000 - 37fef83b
<4>ACPI: RSDP 000F7560, 0014 (r0 Nvidia)
<4>ACPI: RSDT 7FFF3040, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
<4>ACPI: FACP 7FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
<4>ACPI: DSDT 7FFF3180, 65F2 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E)
<4>ACPI: FACS 7FFF0000, 0040
<4>ACPI: SSDT 7FFF9880, 00D6 (r1 PTLTD POWERNOW 1 LTP 1)
<4>ACPI: MCFG 7FFF99C0, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
<4>ACPI: APIC 7FFF97C0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
<7>ACPI: Local APIC address 0xfee00000
<5>1151MB HIGHMEM available.
<5>896MB LOWMEM available.
<6> mapped low ram: 0 - 38000000
<6> low ram: 00000000 - 38000000
<6> bootmap 00011000 - 00018000
<6>(9 early reservations) ==> bootmem [0000000000 - 0038000000]
<6> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 -
0000001000]
<6> #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 -
0000002000]
<6> #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 -
0000007000]
<6> #3 [0000100000 - 0000638a5c] TEXT DATA BSS ==> [0000100000 -
0000638a5c]
<6> #4 [0037a14000 - 0037fef83b] RAMDISK ==> [0037a14000 -
0037fef83b]
<6> #5 [0000639000 - 000063c000] INIT_PG_TABLE ==> [0000639000 -
000063c000]
<6> #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 -
0000100000]
<6> #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 -
0000011000]
<6> #8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 -
0000018000]
<6>found SMP MP-table at [c00f54c0] 000f54c0
<4>Zone PFN ranges:
<4> DMA 0x00000010 -> 0x00001000
<4> Normal 0x00001000 -> 0x00038000
<4> HighMem 0x00038000 -> 0x0007fff0
<4>Movable zone start PFN for each node
<4>early_node_map[2] active PFN ranges
<4> 0: 0x00000010 -> 0x0000009f
<4> 0: 0x00000100 -> 0x0007fff0
<7>On node 0 totalpages: 524159
<7>free_area_init_node: node 0, pgdat c050d300, node_mem_map c1000240
<7> DMA zone: 3947 pages, LIFO batch:0
<7> Normal zone: 223300 pages, LIFO batch:31
<7> HighMem zone: 292304 pages, LIFO batch:31
<6>Using APIC driver default
<6>Nvidia board detected. Ignoring ACPI timer override.
<6>If you got timer trouble try acpi_use_timer_override
<6>ACPI: PM-Timer IO Port: 0x4008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<6>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<4>ACPI: BIOS IRQ0 pin2 override ignored.
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
<7>ACPI: IRQ9 used by override.
<7>ACPI: IRQ14 used by override.
<7>ACPI: IRQ15 used by override.
<4>Enabling APIC mode: Flat. Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<6>SMP: Allowing 2 CPUs, 1 hotplug CPUs
<7>mapped APIC to ffffb000 (fee00000)
<7>mapped IOAPIC to ffffa000 (fec00000)
<6>PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
<6>PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
<6>PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
<6>Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
<6>PERCPU: Allocating 37916 bytes of per cpu data
<7>NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages:
519551
<5>Kernel command line: root=/dev/sda9 vga=0x31a splash=0 3
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 16384 bytes)
<6>TSC: PIT calibration confirmed by PMTIMER.
<6>TSC: using PIT calibration value
<4>Detected 2010.260 MHz processor.
<7>spurious 8259A interrupt: IRQ7.
<4>Console: colour dummy device 80x25
<6>console [tty0] enabled
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 2064936k/2097088k available (2303k kernel code, 30724k
reserved, 1931k data, 280k init, 1179584k highmem)
<6>virtual kernel memory layout:
<6> fixmap : 0xffdf7000 - 0xfffff000 (2080 kB)
<6> pkmap : 0xff400000 - 0xff800000 (4096 kB)
<6> vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
<6> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
<6> .init : 0xc052b000 - 0xc0571000 ( 280 kB)
<6> .data : 0xc033ff93 - 0xc0522cd0 (1931 kB)
<6> .text : 0xc0100000 - 0xc033ff93 (2303 kB)
<6>Checking if this processor honours the WP bit even in supervisor
mode...Ok.
<7>CPA: page pool initialized 1 of 1 pages preallocated
<6>Calibrating delay loop (skipped), value calculated using timer
frequency.. 4020.52 BogoMIPS (lpj=8041040)
<4>kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All
Rights Reserved
<6>Security Framework initialized
<6>AppArmor: AppArmor initialized
<4>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys ns
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys memory
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
<6>CPU: L2 Cache: 512K (64 bytes/line)
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<6>Checking 'hlt' instruction... OK.
<6>SMP alternatives: switching to UP code
<6>ACPI: Core revision 20080609
<6>ACPI: Checking initramfs for custom DSDT
<4>Parsing all Control Methods:
<4>Table [DSDT](id 0001) - 988 Objects with 86 Devices 316 Methods 37
Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0002) - 3 Objects with 0 Devices 0 Methods 0 Regions
<4> tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully
acquired
<4>evxfevnt-0091 [00] enable : Transition to ACPI mode
successful
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
<6>CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 02
<6>Brought up 1 CPUs
<6>Total of 1 processors activated (4020.52 BogoMIPS).
<7>CPU0 attaching NULL sched-domain.
<6>net_namespace: 1044 bytes
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<5>PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
<5>PCI: MCFG area at e0000000 reserved in E820
<6>PCI: Using MMCONFIG for extended config space
<6>PCI: Using configuration type 1 for base access
<5>perfmon: version 2.82
<5>perfmon: CPU hotplug support enabled
<4>evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs
on int 0x9
<4>evgpeblk-0957 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs
on int 0x9
<7>ACPI: EC: Look up EC in DSDT
<4>Completing Region/Field/Buffer/Package
initialization:.................................................................................................................................................
<4>Initialized 33/37 Regions 9/9 Fields 35/35 Buffers 68/79 Packages
(1000 nodes)
<4>Initializing Device/Processor/Thermal objects by executing _INI
methods:...
<4>Executed 3 _INI methods requiring 1 _STA executions (examined 91 objects)
<4>evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 0
Runtime GPEs in this block
<4>evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0
Runtime GPEs in this block
<6>ACPI: Interpreter enabled
<6>ACPI: (supports S0 S1 S3 S4 S5)
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<6>HPET not enabled in BIOS. You might try hpet=force boot option
<7>PCI: 0000:00:01.1 reg 10 io port: [e400, e41f]
<7>PCI: 0000:00:01.1 reg 20 io port: [4c00, 4c3f]
<7>PCI: 0000:00:01.1 reg 24 io port: [4c40, 4c7f]
<6>pci 0000:00:01.1: PME# supported from D3hot D3cold
<6>pci 0000:00:01.1: PME# disabled
<7>PCI: 0000:00:02.0 reg 10 32bit mmio: [d8004000, d8004fff]
<7>pci 0000:00:02.0: supports D1
<7>pci 0000:00:02.0: supports D2
<6>pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:02.0: PME# disabled
<7>PCI: 0000:00:02.1 reg 10 32bit mmio: [feb00000, feb000ff]
<7>pci 0000:00:02.1: supports D1
<7>pci 0000:00:02.1: supports D2
<6>pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:02.1: PME# disabled
<7>PCI: 0000:00:04.0 reg 10 io port: [dc00, dcff]
<7>PCI: 0000:00:04.0 reg 14 io port: [e000, e0ff]
<7>PCI: 0000:00:04.0 reg 18 32bit mmio: [d8003000, d8003fff]
<7>pci 0000:00:04.0: supports D1
<7>pci 0000:00:04.0: supports D2
<7>PCI: 0000:00:06.0 reg 20 io port: [f000, f00f]
<7>PCI: 0000:00:07.0 reg 10 io port: [9f0, 9f7]
<7>PCI: 0000:00:07.0 reg 14 io port: [bf0, bf3]
<7>PCI: 0000:00:07.0 reg 18 io port: [970, 977]
<7>PCI: 0000:00:07.0 reg 1c io port: [b70, b73]
<7>PCI: 0000:00:07.0 reg 20 io port: [d800, d80f]
<7>PCI: 0000:00:07.0 reg 24 32bit mmio: [d8002000, d8002fff]
<7>PCI: 0000:00:08.0 reg 10 io port: [9e0, 9e7]
<7>PCI: 0000:00:08.0 reg 14 io port: [be0, be3]
<7>PCI: 0000:00:08.0 reg 18 io port: [960, 967]
<7>PCI: 0000:00:08.0 reg 1c io port: [b60, b63]
<7>PCI: 0000:00:08.0 reg 20 io port: [c400, c40f]
<7>PCI: 0000:00:08.0 reg 24 32bit mmio: [d8001000, d8001fff]
<7>PCI: 0000:00:0a.0 reg 10 32bit mmio: [d8000000, d8000fff]
<7>PCI: 0000:00:0a.0 reg 14 io port: [b000, b007]
<7>pci 0000:00:0a.0: supports D1
<7>pci 0000:00:0a.0: supports D2
<6>pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:0a.0: PME# disabled
<6>pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:0b.0: PME# disabled
<6>pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:0c.0: PME# disabled
<6>pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:0d.0: PME# disabled
<6>pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:00:0e.0: PME# disabled
<6>pci 0000:00:09.0: transparent bridge
<7>PCI: 0000:01:00.0 reg 10 32bit mmio: [d0000000, d3ffffff]
<7>PCI: 0000:01:00.0 reg 14 64bit mmio: [c0000000, cfffffff]
<7>PCI: 0000:01:00.0 reg 1c 64bit mmio: [d4000000, d4ffffff]
<7>PCI: 0000:01:00.0 reg 30 32bit mmio: [d5000000, d501ffff]
<4>Pre-1.1 PCIe device detected, disable ASPM for 0000:00:0e.0. It can
be enabled forcedly with 'pcie_aspm=force'
<7>PCI: bridge 0000:00:0e.0 32bit mmio: [d0000000, d7ffffff]
<7>PCI: bridge 0000:00:0e.0 64bit mmio pref: [c0000000, cfffffff]
<7>bus 00 -> node 0
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
<6>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15)
<6>ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15)
<6>ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
<6>ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15)
<6>ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
<6>ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
<6>ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
<6>ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
<6>ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
<6>ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
<6>ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
<6>ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
<6>ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
<6>ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
<6>ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
<6>ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
<6>ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
<6>ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
<6>ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>ACPI: bus type pnp registered
<6>pnp: PnP ACPI: found 15 devices
<6>ACPI: ACPI bus type pnp unregistered
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>AppArmor: AppArmor Filesystem Enabled
<4>ACPI: RTC can wake from S4
<6>system 00:01: ioport range 0x4000-0x407f has been reserved
<6>system 00:01: ioport range 0x4080-0x40ff has been reserved
<6>system 00:01: ioport range 0x4400-0x447f has been reserved
<6>system 00:01: ioport range 0x4480-0x44ff has been reserved
<6>system 00:01: ioport range 0x4800-0x487f has been reserved
<6>system 00:01: ioport range 0x4880-0x48ff has been reserved
<6>system 00:02: ioport range 0x4d0-0x4d1 has been reserved
<6>system 00:02: ioport range 0x800-0x87f has been reserved
<6>system 00:02: ioport range 0x290-0x297 has been reserved
<6>system 00:0d: iomem range 0xe0000000-0xefffffff could not be reserved
<6>system 00:0e: iomem range 0xf0000-0xf3fff could not be reserved
<6>system 00:0e: iomem range 0xf4000-0xf7fff could not be reserved
<6>system 00:0e: iomem range 0xf8000-0xfbfff could not be reserved
<6>system 00:0e: iomem range 0xfc000-0xfffff could not be reserved
<6>system 00:0e: iomem range 0x7fff0000-0x7fffffff could not be reserved
<6>system 00:0e: iomem range 0xffff0000-0xffffffff could not be reserved
<6>system 00:0e: iomem range 0x0-0x9ffff could not be reserved
<6>system 00:0e: iomem range 0x100000-0x7ffeffff could not be reserved
<6>system 00:0e: iomem range 0xfec00000-0xfec00fff could not be reserved
<6>system 00:0e: iomem range 0xfee00000-0xfeefffff could not be reserved
<6>system 00:0e: iomem range 0xfefff000-0xfeffffff could not be reserved
<6>system 00:0e: iomem range 0xfff80000-0xfff80fff could not be reserved
<6>system 00:0e: iomem range 0xfff90000-0xfffbffff could not be reserved
<6>system 00:0e: iomem range 0xfffed000-0xfffeffff could not be reserved
<6>pci 0000:00:09.0: PCI bridge, secondary bus 0000:05
<6>pci 0000:00:09.0: IO window: disabled
<6>pci 0000:00:09.0: MEM window: disabled
<6>pci 0000:00:09.0: PREFETCH window: disabled
<6>pci 0000:00:0b.0: PCI bridge, secondary bus 0000:04
<6>pci 0000:00:0b.0: IO window: disabled
<6>pci 0000:00:0b.0: MEM window: disabled
<6>pci 0000:00:0b.0: PREFETCH window: disabled
<6>pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03
<6>pci 0000:00:0c.0: IO window: disabled
<6>pci 0000:00:0c.0: MEM window: disabled
<6>pci 0000:00:0c.0: PREFETCH window: disabled
<6>pci 0000:00:0d.0: PCI bridge, secondary bus 0000:02
<6>pci 0000:00:0d.0: IO window: disabled
<6>pci 0000:00:0d.0: MEM window: disabled
<6>pci 0000:00:0d.0: PREFETCH window: disabled
<6>pci 0000:00:0e.0: PCI bridge, secondary bus 0000:01
<6>pci 0000:00:0e.0: IO window: disabled
<6>pci 0000:00:0e.0: MEM window: 0xd0000000-0xd7ffffff
<6>pci 0000:00:0e.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
<7>pci 0000:00:09.0: setting latency timer to 64
<7>pci 0000:00:0b.0: setting latency timer to 64
<7>pci 0000:00:0c.0: setting latency timer to 64
<7>pci 0000:00:0d.0: setting latency timer to 64
<7>pci 0000:00:0e.0: setting latency timer to 64
<6>bus: 00 index 0 io port: [0, ffff]
<6>bus: 00 index 1 mmio: [0, ffffffff]
<6>bus: 05 index 0 mmio: [0, 0]
<6>bus: 05 index 1 mmio: [0, 0]
<6>bus: 05 index 2 mmio: [0, 0]
<6>bus: 05 index 3 io port: [0, ffff]
<6>bus: 05 index 4 mmio: [0, ffffffff]
<6>bus: 04 index 0 mmio: [0, 0]
<6>bus: 04 index 1 mmio: [0, 0]
<6>bus: 04 index 2 mmio: [0, 0]
<6>bus: 04 index 3 mmio: [0, 0]
<6>bus: 03 index 0 mmio: [0, 0]
<6>bus: 03 index 1 mmio: [0, 0]
<6>bus: 03 index 2 mmio: [0, 0]
<6>bus: 03 index 3 mmio: [0, 0]
<6>bus: 02 index 0 mmio: [0, 0]
<6>bus: 02 index 1 mmio: [0, 0]
<6>bus: 02 index 2 mmio: [0, 0]
<6>bus: 02 index 3 mmio: [0, 0]
<6>bus: 01 index 0 mmio: [0, 0]
<6>bus: 01 index 1 mmio: [d0000000, d7ffffff]
<6>bus: 01 index 2 mmio: [c0000000, cfffffff]
<6>bus: 01 index 3 mmio: [0, 0]
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>Unpacking initramfs...<7>Switched to high resolution mode on CPU 0
<4> done
<6>Freeing initrd memory: 5998k freed
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(1275989476.580:1): initialized
<4>highmem bounce pool size: 64 pages
<6>HugeTLB registered 4 MB page size, pre-allocated 0 pages
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>msgmni has been set to 435
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>perfmon: added sampling format default
<6>pci 0000:00:00.0: Enabling HT MSI Mapping
<6>pci 0000:00:0b.0: Enabling HT MSI Mapping
<6>pci 0000:00:0b.0: Found enabled HT MSI Mapping
<6>pci 0000:00:0b.0: Linking AER extended capability
<6>pci 0000:00:0c.0: Enabling HT MSI Mapping
<6>pci 0000:00:0c.0: Found enabled HT MSI Mapping
<6>pci 0000:00:0c.0: Linking AER extended capability
<6>pci 0000:00:0d.0: Enabling HT MSI Mapping
<6>pci 0000:00:0d.0: Found enabled HT MSI Mapping
<6>pci 0000:00:0d.0: Linking AER extended capability
<6>pci 0000:00:0e.0: Enabling HT MSI Mapping
<6>pci 0000:00:0e.0: Found enabled HT MSI Mapping
<6>pci 0000:00:0e.0: Linking AER extended capability
<7>pci 0000:01:00.0: Boot video device
<7>pcieport-driver 0000:00:0b.0: setting latency timer to 64
<6>pcieport-driver 0000:00:0b.0: found MSI capability
<7>pci_express 0000:00:0b.0:pcie00: allocate port service
<7>pci_express 0000:00:0b.0:pcie03: allocate port service
<7>pcieport-driver 0000:00:0c.0: setting latency timer to 64
<6>pcieport-driver 0000:00:0c.0: found MSI capability
<7>pci_express 0000:00:0c.0:pcie00: allocate port service
<7>pci_express 0000:00:0c.0:pcie03: allocate port service
<7>pcieport-driver 0000:00:0d.0: setting latency timer to 64
<6>pcieport-driver 0000:00:0d.0: found MSI capability
<7>pci_express 0000:00:0d.0:pcie00: allocate port service
<7>pci_express 0000:00:0d.0:pcie03: allocate port service
<7>pcieport-driver 0000:00:0e.0: setting latency timer to 64
<6>pcieport-driver 0000:00:0e.0: found MSI capability
<7>pci_express 0000:00:0e.0:pcie00: allocate port service
<7>pci_express 0000:00:0e.0:pcie03: allocate port service
<6>vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using
10240k, total 262144k

....continued







.