usb cd-burner problem
From: CNerone (chiappami_at_rimpiatt.no)
Date: 03/13/04
- Next message: CNerone: "usb cd-burner problem"
- Previous message: Willie the Wimp: "Re: Final Guide to ACPI with HP Notebooks"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Sat, 13 Mar 2004 20:22:27 GMT
up to some days ago I used my usb cd-burner without problems. Drivers were
load by hotplug deamon.
Now I am not able to make it to run. I'm able to use an other usb-storage
device (iomega click! 40) but not cd-burner.
Often my pc doesn't know cd-burner is connected. Sometimes it know it's
connected but it write about some errors and then "disconnect".
usb-storage: -- transport indicates transport failure
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
sr0: scsi3-mmc drive: 0x/0x caddy
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
usb.c: USB disconnect on device 2
usb-storage: storage_disconnect() called
usb-storage: -- releasing main URB
usb-storage: -- usb_unlink_urb() returned - 19
go on and read the complete dmesg output to evaluate problem:
Linux version 2.4.18-bf2.4 (root@zombie) (gcc version 2.95.4 20011002
(Debian prerelease)) #1 Son Apr 14 09:53:28 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bff8000 (ACPI data)
BIOS-e820: 000000000bff8000 - 000000000c000000 (ACPI NVS)
On node 0 totalpages: 49136
zone(0): 4096 pages.
zone(1): 45040 pages.
zone(2): 0 pages.
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Kernel command line: BOOT_IMAGE=Linux ro root=303
Initializing CPU#0
Detected 332.562 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 663.55 BogoMIPS
Memory: 190124k/196544k available
(1783k kernel code, 6032k reserved, 549k data, 280k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08)
with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller on PCI bus 00 dev 78
ALI15X3: chipset revision 32
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x78c0-0x78c7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x78c8-0x78cf, BIOS settings: hdc:DMA, hdd:pio
hda: FUJITSU MHR2020AT, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 39070080 sectors (20004 MB) w/2048KiB Cache, CHS=2432/255/63, (U)DMA
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
Partition check:
hda: hda1 hda2 < hda5 > hda3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Loading I2O Core - (c) Copyright 1999 Red Hat Software
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
loop: loaded (max 8 devices)
Compaq CISS Driver (v 2.4.5)
HDLC support module revision 1.02 for Linux 2.4
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.97.sv
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver, Apr 14 2002
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.016.
3w-xxxx: No cards with valid units found.
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ cbfefe00
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 128484k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xcc83e000, IRQ 10
usb-ohci.c: usb-00:14.0, Acer Laboratories Inc. [ALi] M5237 USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 149M
agpgart: Detected Ali M1621 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
i2c-core.o: i2c core module
i2c-proc.o version 2.6.1 (20010825)
mice: PS/2 mouse device common for all mice
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
usb.c: registered new driver usblp
printer.c: v0.8:USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
solo1: version v0.19 time 10:28:35 Apr 14 2002
PCI: Guessed IRQ 5 for device 00:08.0
solo1: joystick port at 0x78a5
solo1: ddma base address: 0x7870
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
usb-uhci.c: $Revision: 1.275 $ time 10:29:43 Apr 14 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
VFS: Disk change detected on device ide1(22,0)
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04
Loading Lucent Modem Controller driver version 8.22
Detected Parameters Irq=9 BaseAddress=0x7400 ComAddress=0x7090
Lucent Modem Interface driver version 8.22 (2002-04-11) with SHARE_IRQ enabled
ttyLT00 at 0x7400 (irq = 9) is a Lucent Modem
VFS: Disk change detected on device fd(2,0)
end_request: I/O error, dev 02:00 (floppy), sector 0
VFS: Disk change detected on device fd(2,0)
end_request: I/O error, dev 02:00 (floppy), sector 0
VFS: Disk change detected on device ide1(22,0)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
VFS: Disk change detected on device ide1(22,0)
PPP BSD Compression module registered
hub.c: USB new device connect on bus1/1, assigned device number 2
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 81
usb-storage: Array length appears to be: 83
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc5d284a0 Out: 0xc5d284b4 Int: 0x00000000 (Period 0)
usb-storage: New GUID 059b00573999900000041902
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 00 00 75 5a 1c c0
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 96/255
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x1 R 159 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: IOMEGA Model: CDRW23042EXT3-C Rev: U.12
Type: CD-ROM ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0/1)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 2a 00 80 00 00 00 df e6 24 c0
usb-storage: Bulk command S 0x43425355 T 0xa Trg 0 LUN 0 L 128 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 128 bytes
usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/128
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_transfer_partial(): unknown error
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0xa R 0 Stat 0x2
usb-storage: Bulk reset requested
usb-storage: Bulk soft reset completed
usb-storage: -- transport indicates transport failure
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 2a 00 80 00 00 00 df e6 24 c0
usb-storage: Bulk command S 0x43425355 T 0xb Trg 0 LUN 0 L 128 F 128 CL 6
usb-storage: Bulk command transfer result=-110
usb-storage: Bulk reset requested
usb-storage: Bulk soft reset failed -110
usb-storage: -- transport indicates transport failure
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 2a 00 80 00 00 00 df e6 24 c0
usb-storage: Bulk command S 0x43425355 T 0xc Trg 0 LUN 0 L 128 F 128 CL 6
usb-storage: Bulk command transfer result=-110
usb-storage: Bulk reset requested
usb-storage: Bulk soft reset failed -110
usb-storage: -- transport indicates transport failure
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
sr0: scsi3-mmc drive: 0x/0x caddy
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
usb.c: USB disconnect on device 2
usb-storage: storage_disconnect() called
usb-storage: -- releasing main URB
usb-storage: -- usb_unlink_urb() returned -19
- Next message: CNerone: "usb cd-burner problem"
- Previous message: Willie the Wimp: "Re: Final Guide to ACPI with HP Notebooks"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
