USB DVD-RW not detected

From: Uwe Mayer (merkosh_at_hadiko.de)
Date: 05/29/05 

Date: Sun, 29 May 2005 13:50:42 +0200

Hi,

I have a problem getting my DVD-RW running on my Debian (unstable). K3b does
not detect the device, although "dvdrecord -scanbus" does:

scsibus1:
        1,0,0 100) '_NEC ' 'DVD_RW ND-3500AG' '2.07' Removable CD-ROM
 
Below is what dmesg (with usb debug output) shows. It strikes me that the
DVD drive is connected to sg1 which is a character device.
I also cannot mount any normal CD-Roms in the drive.

Any ideas?

Thanks in advance
Uwe

-- snip --
 strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: Silicon Integrated Systems [SiS] USB 1.0 Controller
usb usb1: Manufacturer: Linux 2.6.5 ohci_hcd
usb usb1: SerialNumber: 0000:00:03.0
usb usb1: registering 1-0:1.0 (config #1, interface 0)
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0000:00:03.0: created debug files
ohci_hcd 0000:00:03.0: OHCI controller state
ohci_hcd 0000:00:03.0: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:03.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:03.0: intrenable 0x80000002 MIE WDH
ohci_hcd 0000:00:03.0: hcca frame #0010
ohci_hcd 0000:00:03.0: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2
ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.0: roothub.status 00000000
ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller
(#2)
ohci_hcd 0000:00:03.1: USB HC TakeOver from BIOS/SMM
ohci_hcd 0000:00:03.1: reset, control = 0x4
ohci_hcd 0000:00:03.1: irq 10, pci mem e09d8000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
usb usb2: Manufacturer: Linux 2.6.5 ohci_hcd
usb usb2: SerialNumber: 0000:00:03.1
usb usb2: registering 2-0:1.0 (config #1, interface 0)
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: no over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
ohci_hcd 0000:00:03.1: created debug files
ohci_hcd 0000:00:03.1: OHCI controller state
ohci_hcd 0000:00:03.1: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:03.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:03.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:03.1: intrenable 0x80000002 MIE WDH
ohci_hcd 0000:00:03.1: hcca frame #0010
ohci_hcd 0000:00:03.1: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2
ohci_hcd 0000:00:03.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.1: roothub.status 00000000
ohci_hcd 0000:00:03.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:03.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 Controller
(#3)
ohci_hcd 0000:00:03.2: USB HC TakeOver from BIOS/SMM
ohci_hcd 0000:00:03.2: reset, control = 0x4
ohci_hcd 0000:00:03.2: irq 11, pci mem e09da000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: root hub device address 1
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb3: Product: Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
usb usb3: Manufacturer: Linux 2.6.5 ohci_hcd
usb usb3: SerialNumber: 0000:00:03.2
usb usb3: registering 3-0:1.0 (config #1, interface 0)
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: unknown reserved power switching mode
hub 3-0:1.0: no over-current protection
hub 3-0:1.0: Port indicators are not supported
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: hub controller current requirement: 0mA
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
hub 3-0:1.0: enabling power on all ports
ohci_hcd 0000:00:03.2: created debug files
ohci_hcd 0000:00:03.2: OHCI controller state
ohci_hcd 0000:00:03.2: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:03.2: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:03.2: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.2: intrstatus 0x00000004 SF
ohci_hcd 0000:00:03.2: intrenable 0x80000002 MIE WDH
ohci_hcd 0000:00:03.2: hcca frame #0010
ohci_hcd 0000:00:03.2: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2
ohci_hcd 0000:00:03.2: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.2: roothub.status 00000000
ohci_hcd 0000:00:03.2: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:03.2: roothub.portstatus [1] 0x00000100 PPS
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2
ordered !ppc ports=6
ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024
ehci_hcd 0000:00:03.3: capability 0001 at 70
ehci_hcd 0000:00:03.3: irq 9, pci mem e0a14000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:03.3: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024
RUN
ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
ehci_hcd 0000:00:03.3: root hub device address 1
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb4: Product: Silicon Integrated Systems [SiS] USB 2.0 Controller
usb usb4: Manufacturer: Linux 2.6.5 ehci_hcd
usb usb4: SerialNumber: 0000:00:03.3
usb usb4: registering 4-0:1.0 (config #1, interface 0)
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: ganged power switching
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: Single TT
hub 4-0:1.0: TT requires at most 8 FS bit times
hub 4-0:1.0: Port indicators are not supported
hub 4-0:1.0: power on to power good time: 20ms
hub 4-0:1.0: hub controller current requirement: 0mA
hub 4-0:1.0: local power source is good
hub 4-0:1.0: no over-current condition exists
hub 4-0:1.0: enabling power on all ports
dc395x: Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040 v2.05, 2004/03/08
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [1] = 0x00010300 CSC
LSDA PPS
hub 1-0:1.0: port 1, status 300, change 1, 1.5 Mb/s
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 1-0:1.0: port 2, status 100, change 1, 12 Mb/s
ehci_hcd 0000:00:03.3: GetStatus port 1 status 001803 POWER sig=j CSC
CONNECT
hub 4-0:1.0: port 1, status 501, change 1, 480 Mb/s
dc395x: Used settings: AdapterID=07, Speed=0(20.0MHz), dev_mode=0x77
dc395x: AdaptMode=0x0f, Tags=4(16), DelayReset=1s
dc395x: (Wide) Connectors: int68 Termination: Auto Low High
dc395x: Performing initial SCSI bus reset
scsi0 : Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040 v2.05, 2004/03/08
hub 4-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501
ehci_hcd 0000:00:03.3: port 1 high speed
ehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE
CONNECT
usb 4-1: new high speed USB device using address 2
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=3
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 4-1: Product: LaCie DVDRW USB
usb 4-1: Manufacturer: LaCie
usb 4-1: SerialNumber: 10000E0001AC71F3
usb 4-1: registering 4-1:1.0 (config #1, interface 0)
usb-storage 4-1:1.0: usb_probe_interface
usb-storage 4-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: altsetting is 0, id_index is 91
usb-storage: -- associate_dev
usb-storage: Transport: Bulk
usb-storage: Protocol: 8070i
usb-storage: Endpoints: In: 0xc99d3700 Out: 0xc99d3714 Int: 0x00000000
(Period 0)
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
dc395x: Target 00: Wide16 Sync: 48ns Offset 15 (41.7 MB/s)
  Vendor: IBM Model: DCAS-34330W Rev: S65A
  Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 8467200 512-byte hdwr sectors (4335 MB)
SCSI device sda: drive cache: write back
 sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 60 00
usb-storage: Bulk Command S 0x43425355 T 0x11 L 96 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 96 bytes
usb-storage: Status code 0; transferred 96/96
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
  Vendor: _NEC Model: DVD_RW ND-3500AG Rev: 2.07
  Type: CD-ROM ANSI SCSI revision: 02
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
USB Mass Storage device found at 2
ehci_hcd 0000:00:03.3: GetStatus port 4 status 001803 POWER sig=j CSC
CONNECT
hub 4-0:1.0: port 4, status 501, change 1, 480 Mb/s
hub 4-0:1.0: debounce: port 4: delay 100ms stable 4 status 0x501
ehci_hcd 0000:00:03.3: port 4 full speed --> companion
ehci_hcd 0000:00:03.3: GetStatus port 4 status 003001 POWER OWNER sig=se0
CONNECT
ehci_hcd 0000:00:03.3: GetStatus port 4 status 003002 POWER OWNER sig=se0
CSC
hub 4-0:1.0: port 4, status 0, change 1, 12 Mb/s
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS
CCS
hub 1-0:1.0: port 2, status 101, change 1, 12 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: new full speed USB device using address 2
usb 1-2: new device strings: Mfr=0, Product=1, SerialNumber=0
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 1-2: Product: Camera
usb 1-2: registering 1-2:1.0 (config #1, interface 0)
lirc_dev: IR Remote Control driver registered, at major 61
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
lirc_dev: lirc_register_plugin:sample_rate: 10
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
-- /snip --

Quantcast