Re: ACPI Problems

From: Charles (charlestaylor_at_bellsouth.net)
Date: 07/31/03

  • Next message: James Knott: "Re: suspend and hibernate commands?" 
    Date: 31 Jul 2003 12:42:17 -0700

    Todd,

    Check your kernel config to make sure APM is NOT built at all, not
    compiled into the kernel, not built as a module. Sometimes ACPI and
    APM loading at the same time will hang the system at boot.

    Charles

    matlabguru@yahoo.com (Todd) wrote in message news:<a569f671.0307300642.6ec5cbe0@posting.google.com>...
    > I patched an official kernel and I'm hanging at boot at the same place.
    >
    >
    > "FluFlo" <flo_flo@hotmail.com> wrote in message news:<bg5qhf$i3e$1@tro.champinet.es>...
    > > Patches against the official kernel series worlk very badly when applied to
    > > mdk kernels. Is this your case?. I recommend you to download an entire
    > > new kernel from www.kernel.org (2.4.21) and apply the patches you want
    > > there.
    > >
    > > Good luck
    > >
    > >
    > > "Todd" <matlabguru@yahoo.com> escribió en el mensaje
    > > news:a569f671.0307281724.5fd31888@posting.google.com...
    > > > I'm running mandrake 9.1 on an HP Pavilion ze4300. I've recompiled my
    > > > kernel 2.4.21 with the latest acpi patch. I've also disassembled
    > > > dsdt.hex, modifying and reassembling. When I boot with acpi enabled
    > > > (apm=off pci=noacpi) it hangs with the last line reading "Executing
    > > > all Device _STA and_INI methods:...". I've included the output of
    > > > dmesg and lspci -vv below when I disable acpi. My bios doesnt include
    > > > any settings for pnp or acpi. Also, in dmesg I get a warning for
    > > > "redundant entry in pci table", and for pci 0:10.0 pin A is routed to
    > > > IRQ 0.
    > > >
    > > > Thanks in advance
    > > >
    > > > dmesg
    > > > -----------
    > > >
    > > > Linux version 2.4.21-0.13mdkcustom (root@coredump) (gcc version 3.2.2
    > > > (Mandrake Linux 9.1 3.2.2-3mdk)) #1 Mon Jul 21 22:23:52 EDT 2003
    > > > BIOS-provided physical RAM map:
    > > > BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    > > > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    > > > BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
    > > > BIOS-e820: 0000000000100000 - 000000000bef0000 (usable)
    > > > BIOS-e820: 000000000bef0000 - 000000000beff000 (ACPI data)
    > > > BIOS-e820: 000000000beff000 - 000000000bf00000 (ACPI NVS)
    > > > BIOS-e820: 000000000bf00000 - 000000000c000000 (reserved)
    > > > BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
    > > > 190MB LOWMEM available.
    > > > ACPI: have wakeup address 0xc0001000
    > > > On node 0 totalpages: 48880
    > > > zone(0): 4096 pages.
    > > > zone(1): 44784 pages.
    > > > zone(2): 0 pages.
    > > > Kernel command line: BOOT_IMAGE=linux-alpha ro root=305 devfs=mount
    > > > hdc=ide-scsi acpi=off pci=biosirq
    > > > ide_setup: hdc=ide-scsi
    > > > Local APIC disabled by BIOS -- reenabling.
    > > > Found and enabled local APIC!
    > > > Initializing CPU#0
    > > > Detected 1656.387 MHz processor.
    > > > Console: colour VGA+ 80x25
    > > > Calibrating delay loop... 3303.01 BogoMIPS
    > > > Memory: 189820k/195520k available (1481k kernel code, 5312k reserved,
    > > > 1165k data, 136k init, 0k highmem)
    > > > Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
    > > > Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
    > > > Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    > > > Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
    > > > Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
    > > > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    > > > CPU: L2 Cache: 256K (64 bytes/line)
    > > > Intel machine check architecture supported.
    > > > Intel machine check reporting enabled on CPU#0.
    > > > CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
    > > > CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
    > > > CPU: AMD mobile AMD Athlon(tm) XP 2000+ stepping 01
    > > > Enabling fast FPU save and restore... done.
    > > > Enabling unmasked SIMD FPU exception support... done.
    > > > Checking 'hlt' instruction... OK.
    > > > POSIX conformance testing by UNIFIX
    > > > enabled ExtINT on CPU#0
    > > > ESR value before enabling vector: 00000000
    > > > ESR value after enabling vector: 00000000
    > > > Using local APIC timer interrupts.
    > > > calibrating APIC timer ...
    > > > ..... CPU clock speed is 1656.3719 MHz.
    > > > ..... host bus clock speed is 265.0193 MHz.
    > > > cpu: 0, clocks: 2650193, slice: 1325096
    > > > CPU0<T0:2650192,T1:1325088,D:8,S:1325096,C:2650193>
    > > > mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
    > > > mtrr: detected mtrr type: Intel
    > > > ACPI: Subsystem revision 20030122
    > > > ACPI: Disabled via command line (acpi=off)
    > > > PCI: PCI BIOS revision 2.10 entry at 0xfd87b, last bus=2
    > > > PCI: Using configuration type 1
    > > > PCI: Probing PCI hardware
    > > > PCI: ACPI tables contain no PCI IRQ routing entries
    > > > PCI: Probing PCI hardware (bus 00)
    > > > PCI: Using IRQ router ALI [10b9/1533] at 00:07.0
    > > > ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
    > > > isapnp: Scanning for PnP cards...
    > > > isapnp: No Plug & Play device found
    > > > Linux NET4.0 for Linux 2.4
    > > > Based upon Swansea University Computer Society NET3.039
    > > > Initializing RT netlink socket
    > > > Starting kswapd
    > > > VFS: Disk quotas vdquot_6.5.1
    > > > devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
    > > > devfs: boot_options: 0x1
    > > > pty: 256 Unix98 ptys configured
    > > > Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS
    > > > MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
    > > > ttyS00 at 0x03f8 (irq = 4) is a 16550A
    > > > PCI: Found IRQ 3 for device 00:08.0
    > > > Redundant entry in serial pci_table. Please send the output of
    > > > lspci -vv, this message (10b9,5457,103c,0024)
    > > > and the manufacturer and name of serial board or modem board
    > > > to serial-pci-info@lists.sourceforge.net.
    > > > register_serial(): autoconfig failed
    > > > RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
    > > > Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
    > > > ide: Assuming 33MHz system bus speed for PIO modes; override with
    > > > idebus=xx
    > > > Warning: ATI Radeon IGP Northbridge is not yet fully tested.
    > > > ALI15X3: IDE controller at PCI slot 00:10.0
    > > > PCI: No IRQ known for interrupt pin A of device 00:10.0.
    > > > ALI15X3: chipset revision 196
    > > > ALI15X3: not 100% native mode: will probe irqs later
    > > > ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
    > > > ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:pio, hdd:pio
    > > > hda: IC25N040ATCS04-0, ATA DISK drive
    > > > blk: queue c03e7480, I/O limit 4095Mb (mask 0xffffffff)
    > > > hdc: TOSHIBA DVD-ROM SD-R2312, ATAPI CD/DVD-ROM drive
    > > > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    > > > ide1 at 0x170-0x177,0x376 on irq 15
    > > > hda: host protected area => 1
    > > > hda: 78140160 sectors (40008 MB) w/1768KiB Cache, CHS=4864/255/63,
    > > > UDMA(100)
    > > > Partition check:
    > > > /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
    > > > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    > > > md: Autodetecting RAID arrays.
    > > > md: autorun ...
    > > > md: ... autorun DONE.
    > > > NET4: Linux TCP/IP 1.0 for NET4.0
    > > > IP Protocols: ICMP, UDP, TCP, IGMP
    > > > IP: routing cache hash table of 1024 buckets, 8Kbytes
    > > > TCP: Hash tables configured (established 16384 bind 32768)
    > > > Linux IP multicast router 0.06 plus PIM-SM
    > > > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    > > > RAMDISK: Compressed image found at block 0
    > > > Freeing initrd memory: 107k freed
    > > > VFS: Mounted root (ext2 filesystem).
    > > > Mounted devfs on /dev
    > > > Journalled Block Device driver loaded
    > > > kjournald starting. Commit interval 5 seconds
    > > > EXT3-fs: mounted filesystem with ordered data mode.
    > > > Mounted devfs on /dev
    > > > Freeing unused kernel memory: 136k freed
    > > > Real Time Clock Driver v1.10e
    > > > usb.c: registered new driver usbdevfs
    > > > usb.c: registered new driver hub
    > > > PCI: Assigned IRQ 9 for device 00:02.0
    > > > usb-ohci.c: USB OHCI at membase 0xcc83a000, IRQ 9
    > > > usb-ohci.c: usb-00:02.0, Acer Laboratories Inc. [ALi] USB 1.1
    > > > Controller
    > > > usb.c: new USB bus registered, assigned bus number 1
    > > > hub.c: USB hub found
    > > > hub.c: 4 ports detected
    > > > usbdevfs: remount parameter error
    > > > EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
    > > > Adding Swap: 506008k swap-space (priority -1)
    > > > SCSI subsystem driver Revision: 1.00
    > > > scsi0 : SCSI host adapter emulation for IDE ATAPI devices
    > > > Vendor: TOSHIBA Model: DVD-ROM SD-R2312 Rev: 1905
    > > > Type: CD-ROM ANSI SCSI revision: 02
    > > > kjournald starting. Commit interval 5 seconds
    > > > EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
    > > > EXT3-fs: mounted filesystem with ordered data mode.
    > > > NTFS driver 2.1.1a [Flags: R/O MODULE].
    > > > NTFS volume version 3.1.
    > > > natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
    > > > originally by Donald Becker <becker@scyld.com>
    > > > http://www.scyld.com/network/natsemi.html
    > > > 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
    > > > PCI: Found IRQ 11 for device 00:12.0
    > > > eth0: NatSemi DP8381[56] at 0xcc84b000, 00:0b:cd:a4:50:50, IRQ 11.
    > > > inserting floppy driver for 2.4.21-0.13mdkcustom
    > > > FDC 0 is a post-1991 82077
    > > > Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
    > > > sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    > > > Uniform CD-ROM driver Revision: 3.12
    > > > eth0: link up.
    > > > eth0: Setting full-duplex based on negotiated link capability.
    > > > Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    > > > Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version
    > > > 0.14.10h, 22:50:33 Jul 21 2003
    > > > PCI: Found IRQ 5 for device 00:06.0
    > > > trident: ALi Audio Accelerator found at IO 0x8400, IRQ 5
    > > > ac97_codec: AC97 Modem codec, id: CXT41 (Unknown)
    > > > PCI: Found IRQ 5 for device 00:06.0
    > > > gameport0: Acer Laboratories Inc. [ALi] M5451 PCI AC-Link Controller
    > > > Audio Device at pci00:06.0 speed 2711 kHz
    > > > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
    > > > parport0: irq 7 detected
    > > > lp0: using parport0 (polling).
    > > >
    > > >
    > > > lspci -vv
    > > > ------------
    > > > 00:00.0 Host bridge: ATI Technologies Inc: Unknown device cab0 (rev
    > > > 13)
    > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort+ >SERR- <PERR-
    > > > Latency: 32
    > > > Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
    > > > Region 1: Memory at d0500000 (32-bit, prefetchable) [size=4K]
    > > > Region 2: I/O ports at 8090 [disabled] [size=4]
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:01.0 PCI bridge: ATI Technologies Inc U1/A3 AGP Bridge [IGP 320M]
    > > > (rev 01) (prog-if 00 [Normal decode])
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 99
    > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
    > > > I/O behind bridge: 00009000-00009fff
    > > > Memory behind bridge: d0100000-d01fffff
    > > > Prefetchable memory behind bridge: e0000000-efffffff
    > > > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
    > > >
    > > > 00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
    > > > (prog-if 10 [OHCI])
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 64 (20000ns max)
    > > > Interrupt: pin A routed to IRQ 9
    > > > Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link
    > > > Controller Audio Device (rev 02)
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR+ <PERR+
    > > > Latency: 64 (500ns min, 6000ns max)
    > > > Interrupt: pin A routed to IRQ 5
    > > > Region 0: I/O ports at 8400 [size=256]
    > > > Region 1: Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin
    > > > IV]
    > > > Subsystem: ALi Corporation ALI M1533 Aladdin IV ISA Bridge
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 0
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:08.0 Modem: ALi Corporation Intel 537 [M5457 AC-Link Modem]
    > > > (prog-if 00 [Generic])
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Interrupt: pin A routed to IRQ 3
    > > > Region 0: Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
    > > > Region 1: I/O ports at 8800 [size=256]
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 32
    > > > Interrupt: pin A routed to IRQ 5
    > > > Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=4K]
    > > > Bus: primary=00, secondary=02, subordinate=05, sec-latency=32
    > > > Memory window 0: 81000000-81100000
    > > > I/O window 0: 00003000-0000307f
    > > > I/O window 1: 00000000-00000003
    > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite-
    > > >
    > > > 00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if b0)
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 32 (500ns min, 1000ns max)
    > > > Interrupt: pin A routed to IRQ 0
    > > > Region 4: I/O ports at 8080 [size=16]
    > > > Capabilities: <available only to root>
    > > >
    > > > 00:11.0 Bridge: ALi Corporation M7101 PMU
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > >
    > > > 00:12.0 Ethernet controller: National Semiconductor Corporation
    > > > DP83815 (MacPhyter) Ethernet Controller
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping- SERR- FastB2B-
    > > > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 90 (2750ns min, 13000ns max)
    > > > Interrupt: pin A routed to IRQ 11
    > > > Region 0: I/O ports at 8c00 [size=256]
    > > > Region 1: Memory at d0003000 (32-bit, non-prefetchable) [size=4K]
    > > > Expansion ROM at <unassigned> [disabled] [size=64K]
    > > > Capabilities: <available only to root>
    > > >
    > > > 01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown
    > > > device 4136 (prog-if 00 [VGA])
    > > > Subsystem: Hewlett-Packard Company: Unknown device 0024
    > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > > > Stepping+ SERR- FastB2B+
    > > > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > > > <TAbort- <MAbort- >SERR- <PERR-
    > > > Latency: 66 (2000ns min), cache line size 10
    > > > Interrupt: pin A routed to IRQ 10
    > > > Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
    > > > Region 1: I/O ports at 9000 [size=256]
    > > > Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
    > > > Expansion ROM at <unassigned> [disabled] [size=128K]
    > > > Capabilities: <available only to root>

  • Next message: James Knott: "Re: suspend and hibernate commands?"

    Relevant Pages

    • [SLE] User mode linux and SuSE 9.0
      ... Has anyone successfully ran a UML with a SuSE built kernel? ... Using a pre-built kernel is not an option for me since I need FreeS/WAN, ... POPTOP and ACL patches. ... I've yet to se any UML kernels with all these ...
      (SuSE)
    • Re: OOM killer in 2.6.31-rc2
      ... I had built a 2nd version of the 2.6.31-rc2 kernel last night when I found the ... Normal zone is absent in the above lines. ... More majordomo info at http://vger.kernel.org/majordomo-info.html ...
      (Linux-Kernel)
    • OOM killer in 2.6.31-rc2
      ... I had built a 2nd version of the 2.6.31-rc2 kernel last night when I found the ... fixes the very early boot time oops, also leaves me with a machine that will ... newer versions are _not_ stable, this is stable after the fix. ...
      (Linux-Kernel)
    • Re: Question for Gene Heskett about slow Firefox launch
      ... How NSA access was built into Windows" ... I believe you will have to build a generic kernel.org kernel ... as you go thru the xconfig screens item ... window, and it says "if you don't know what this option does, you ...
      (Fedora)
    • Re: Question for Gene Heskett about slow Firefox launch
      ... On Wednesday 17 January 2007 01:36, Ric Moore wrote: ... How NSA access was built into Windows" ... I believe you will have to build a generic kernel.org kernel ... hour to work in an xconfig window. ...
      (Fedora)