Re: Can't erase CD-RW's under SuSE 8.2
From: David (thunderbolt01_at_netscape.net)
Date: 08/23/03
- Next message: Sime: "Re: Desktop Distribution and WM for P266"
- Previous message: John Winters: "Re: Removing kernels"
- In reply to: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Next in thread: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Reply: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Sat, 23 Aug 2003 19:51:14 GMT
someone wrote:
> Thanks very much for your answer.
> I tried it out, but it aborts with the same error message as I receive
> with xcdroast, namely (after the error message there is the error
> message I get when I use blank=all):
>
> cdrecord dev="0,0,0" -v blank=fast
> Cdrecord 2.0 (i686-suse-linux) Copyright (C) 1995-2002 Jörg Schilling
> TOC Type: 1 = CD-ROM
> scsidev: '0,0,0'
> scsibus: 0 target: 0 lun: 0
> Linux sg driver version: 3.1.24
> Using libscg version 'schily-0.7'
> cdrecord: Warning: using inofficial libscg transport code version
> (okir@suse.de-
> scsi-linux-sg.c-1.75-resmgr-patch '@(#)scsi-linux-sg.c 1.75 02/10/21
> Copyright
> 1997 J. Schilling').
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 2
> Capabilities :
> Vendor_info : 'QSI '
> Identifikation : 'DVD/CDRW SBW-161'
> Revision : 'SX09'
> Device seems to be: Generic mmc2 DVD-ROM.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : MMC-2 SWABAUDIO BURNFREE
> Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
> RAW/R96R
> Drive buf size : 1605632 = 1568 KB
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 5
> Reference speed: 2
> Is unrestricted
> Is erasable
> ATIP start of lead in: -11597 (97:27/28)
> ATIP start of lead out: 359849 (79:59/74)
> 1T speed low: 0 (reserved val 0) 1T speed high: 4
> 2T speed low: 0 (reserved val 5) 2T speed high: 0 (reserved val
> 10)
> power mult factor: 3 6
> recommended erase/write power: 3
> A1 values: 02 3C B0
> A2 values: 5A C8 16
> Disk type: Phase change
> Manuf. index: 20
> Manufacturer: Princo Corporation
> Blocks total: 359849 Blocks current: 258484 Blocks remaining: 258634
> Starting to write CD/DVD at speed 4 in real BLANK mode for single
> session.
> Last chance to quit, starting real write 0 seconds. Operation
> starts.
> Performing OPC...
> Blanking PMA, TOC, pregap
> cdrecord: Input/output error. blank unit: scsi sendcmd: no error
> CDB: A1 01 00 00 00 00 00 00 00 00 00 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 24 00 00 00
> Sense Key: 0x5 Illegal Request, Segment 0
> Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
> Sense flags: Blk 0 (not valid)
> cmd finished after 0.000s timeout 9600s
> cdrecord: Cannot blank disk, aborting.
> cdrecord: Some drives do not support all blank types.
> cdrecord: Try again with cdrecord blank=all.
>
> Now I tried blank=all which yielded the following error message:
>
> cdrecord dev="0,0,0" -v blank=all
> Cdrecord 2.0 (i686-suse-linux) Copyright (C) 1995-2002 Jörg Schilling
> TOC Type: 1 = CD-ROM
> scsidev: '0,0,0'
> scsibus: 0 target: 0 lun: 0
> Linux sg driver version: 3.1.24
> Using libscg version 'schily-0.7'
> cdrecord: Warning: using inofficial libscg transport code version
> (okir@suse.de-scsi-linux-sg.c-1.75-resmgr-patch '@(#)scsi-linux-sg.c
> 1.75 02/10/21 Copyright 1997 J. Schilling').
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 2
> Capabilities :
> Vendor_info : 'QSI '
> Identifikation : 'DVD/CDRW SBW-161'
> Revision : 'SX09'
> Device seems to be: Generic mmc2 DVD-ROM.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : MMC-2 SWABAUDIO BURNFREE
> Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
> RAW/R96R
> Drive buf size : 1605632 = 1568 KB
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 5
> Reference speed: 2
> Is unrestricted
> Is erasable
> ATIP start of lead in: -11597 (97:27/28)
> ATIP start of lead out: 359849 (79:59/74)
> 1T speed low: 0 (reserved val 0) 1T speed high: 4
> 2T speed low: 0 (reserved val 5) 2T speed high: 0 (reserved val
> 10)
> power mult factor: 3 6
> recommended erase/write power: 3
> A1 values: 02 3C B0
> A2 values: 5A C8 16
> Disk type: Phase change
> Manuf. index: 20
> Manufacturer: Princo Corporation
> Blocks total: 359849 Blocks current: 258484 Blocks remaining: 258634
> Starting to write CD/DVD at speed 4 in real BLANK mode for single
> session.
> Last chance to quit, starting real write 0 seconds. Operation
> starts.
> Performing OPC...
> Blanking entire disk
> cdrecord: Input/output error. blank unit: scsi sendcmd: no error
> CDB: A1 00 00 00 00 00 00 00 00 00 00 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 24 00 00 00
> Sense Key: 0x5 Illegal Request, Segment 0
> Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
> Sense flags: Blk 0 (not valid)
> cmd finished after 0.000s timeout 9600s
> cdrecord: Cannot blank disk, aborting.
>
> The error seems to be somewhere in the system, any idea where?
Have you tried different drivers?
# cdrecord --driverhelp # shows available drivers
# cdrecord driver=drivername
-- Confucius: He who play in root, eventually kill tree. Registered with The Linux Counter. http://counter.li.org/ Slackware 9.0 Kernel 2.4.21 i686 (GCC) 3.3 Uptime: 6 days, 12:49, 1 user, load average: 1.17, 1.19, 1.18
- Next message: Sime: "Re: Desktop Distribution and WM for P266"
- Previous message: John Winters: "Re: Removing kernels"
- In reply to: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Next in thread: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Reply: someone: "Re: Can't erase CD-RW's under SuSE 8.2"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
