Re: How long does DD take? 180GB?

From: Frank Burns (frankburnz_at_hotmail.com)
Date: 10/09/03 

Date: 8 Oct 2003 17:43:24 -0700

> Ohh. *OUCH*, that sucks. Couldn't you buy or borrow another RAID
> controller to speed this process?

Okay here is the status & other problems:
I used this command (after I enabled DMA (3.47MB/sec vs 47.9MB/sec))

dd if=/dev/hda of=/dev/hdb bs=32M

it said:

171705+1 records in
171705+1 records out
180,045,766,656 bytes
35822.125322 seconds (I think it was about 2 hours in reality, it
can't add right)
5,025,105 bytes/sec

(notice the records are different, for identical drives)

Now I didn't think I could use another RAID controller, (can I???)
Whenever I try to reboot on the Old RAID it says "Raid Offline" so I
can get into it, can I? If I get another raid controller, can I
install my new raid on my motherboard, the old raid on the controller
and copy the old raid to the new raid?

This is an entire 1 partition WinXP SP1 Partition NTFS 5.1, (I know, I
know) on this computer.

I copied the two drives, and remember I did get an error message when
I copied the first drive, I put them back in, and they didn't work.
The RAID bios said the two drives were FREE and not in an array. So
does DD not copy everything? the raid info is stored on the HDD, not
the raid bios. Do I need to go to a DATA restorer guy and see if I can
use a physical HDD copier?

Help!

Raid sucks. I dislike raid 0 for obvious reasons, but it is so
noticably faster. I dislike raid 1 because if one OS goes south,
you're screwed, twice over. But it's better. I guess RAID 0,1 or 5 is
best. but I'm not made of money... maybe I should be.

Relevant Pages

  • Re: SATA vs. SCSI, RAID?
    ... Also this would depend on which controller is ... Well MS's intrinsic SW RAID 1 drivers using typical Intel mobo EIDE ... controllers for ATA or Adaptec SCSI non-RAID cards do very well here. ... But do note that I only mentioned "3x drives ...
    (microsoft.public.windows.server.sbs)
  • Re: Do I have the correct SATA controller installed ?
    ... My intention is to use the 2 SATA hard drives as stand alone drives, ... I was just concerned I might have choosen the wrong ICH7 controller ... > Youre going about it wrong.First,if not running RAID then only 1 hd must ... >> I selected the 82801GB AHCI controller and Windows continued to install ...
    (microsoft.public.windowsxp.hardware)
  • Re: Upgrading to Hardware RAID SBS2000
    ... depends on the RAID controller but as a general rule I'd suggest putting the ... Prug'n'pray should detect the RAID and allow you to ... other drives, be migrated non-destructively between RAID levels. ... > for installing a HW RAID card into an existing server? ...
    (microsoft.public.backoffice.smallbiz2000)
  • Re: bad blocks on raid5 cause filesystem failure
    ... It is setup in in RAID 5. ... How could a RAID controller botch this up? ... should be rebuilt on spare drive if available from remaining drives. ... All is fine unless you have double fault. ...
    (comp.os.linux.hardware)
  • Re: on board RAID chip
    ... I don't actually want to use RAID, real or otherwise, ... the two IDE channels that the "raid" chip controls, ... 8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, ... > harddrive over to the second channel and tried to boot. ...
    (Debian-User)