Re: problem with ohci1394

From: Michele (mikfiNOSPAMM_at_yahoo.com)
Date: 09/22/04


Date: Wed, 22 Sep 2004 12:12:39 GMT


[..]
>
> You complain about these messages, but I find them quite helpful.

well, I forgot to say that I'm quite ignorant about linux ;-)

> What does looking into syslog, looking at /var/log/messages and running
> dmesg tell you?

well... probably I didn't run it inthe proper way: it is rather long:

# dmesg
Linux version 2.4.20-33.9.Linoxcustom (root@hed035-199.research.nokia.com)
(gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Sep 6 10:11:42
EEST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
 BIOS-e820: 000000000fff0000 - 000000000fffec00 (ACPI data)
 BIOS-e820: 000000000fffec00 - 0000000010000000 (ACPI NVS)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: root=/dev/ram0 rw init=/linuxrc
Initializing CPU#0
Detected 696.978 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1389.36 BogoMIPS
Memory: 251836k/262080k available (1363k kernel code, 7812k reserved, 1008k
data, 132k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
PCI: Found IRQ 11 for device 00:03.1
PCI: Sharing IRQ 11 with 00:03.0
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (115d,000c,8086,2408)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:pio, hdd:pio
hda: HTS548080M9AT00, ATA DISK drive
blk: queue c03d0060, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/7877KiB Cache, CHS=9729/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1225k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 132k freed
loop: loaded (max 16 devices)
cryptoapi: loaded
cryptoloop: loaded
init_ppdd
cryptoapi: Registered ppdd-cbc (65536)
Journalled Block Device driver loaded
ppdd_lock
ppdd_set_key: key_len=0 atomic=0
ppdd_unlock
ppdd_lock
ppdd_set_key: key_len=1844 atomic=0
ppdd_unlock
ppdd_lock
ppdd_set_key: key_len=0 atomic=0
ppdd_unlock
ppdd_lock
ppdd_set_key: key_len=1844 atomic=0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ppdd_lock
ppdd_set_key: key_len=0 atomic=0
ppdd_unlock
ppdd_lock
ppdd_set_key: key_len=1844 atomic=0
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 11:00:03 Sep 6 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x1860, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,0), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 470008k swap-space (priority -1)
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
SCSI subsystem driver Revision: 1.00
Intel(R) PRO/100 Network Driver - version 2.2.21-k1
Copyright (c) 2003 Intel Corporation

PCI: Found IRQ 11 for device 00:03.0
PCI: Sharing IRQ 11 with 00:03.1
e100: selftest OK.
divert: allocating divert_blk for eth0
e100: eth0: Intel(R) PRO/100 Network Connection
  Hardware receive checksums enabled
  cpu cycle saver enabled

divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 292 bytes per conntrack
Intel(R) PRO/100 Network Driver - version 2.2.21-k1
Copyright (c) 2003 Intel Corporation

PCI: Found IRQ 11 for device 00:03.0
PCI: Sharing IRQ 11 with 00:03.1
e100: selftest OK.
divert: allocating divert_blk for eth0
e100: eth0: Intel(R) PRO/100 Network Connection
  Hardware receive checksums enabled
  cpu cycle saver enabled

parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
lp0: using parport0 (polling).
lp0: console ready
IrCOMM protocol (Dag Brattli)
PCI: Found IRQ 11 for device 00:05.0
PCI: Sharing IRQ 11 with 00:02.0
PCI: Sharing IRQ 11 with 01:00.0
Crystal 4280/46xx + AC97 Audio, version 1.28.32, 10:56:50 Sep 6 2004
cs46xx: Card found at 0xe8122000 and 0xe8000000, IRQ 11
cs46xx: Thinkpad 600X/A20/T20 (1014:0153) at 0xe8122000/0xe8000000, IRQ 11
ac97_codec: AC97 Audio codec, id: CRY20 (Cirrus Logic CS4297A rev B)

 
> If you have the RedHat 8 installation where it worked available, check
> the IRQ and IO settings you had there (as listed in /proc).

unluckily I don't have it anymore.

> Sorry that I even consider that you made such a trivial mistake,

please don't overextimate me :-) I am a beginner!

> but did
> you compile and install the kernel modules correctly?

I assume so.... other modules that I've been compiling (like ieee1394 can be
loaded succesfully).

> Did you run 'depmod -a'? Any messages?

no messages...

> Is the /etc/modules.conf the same as on the RedHat 8 system?

I don't know.... don't have it anymore.
 
> Do other modules load without problem?

yes they load without problem.
 
Thanks for your help.

- michele



Relevant Pages