Cyclades TS800 Firmware Upgrade
From: CUT (snm_uk(CUT)_at_hotmail.com)
Date: 12/09/03
- Next message: Eli Aran: "used to windows"
- Previous message: Axel Burwitz: "Re: fedora welcome screen freezes after first install and after booting / ATI Radeon 9800 AGP8x"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Date: Tue, 9 Dec 2003 12:24:46 -0000
I've just attempted to upgrade from Ver 1.3.1 to 1.3.9 on a TS800.
Followed instructions as per website, ie removed all references to ssh
from /etc/config_files did a saveconf and reboot.
Now I get the following... any ideas? Thanks in advance.
Linux/PPC load: root=/dev/ram ramdisk=0x00002000
ncompressing Linux...done.
Now booting the kernel
Linux version 2.2.14 (root@dell) (gcc version 2.95.2 19991030 (2.95.3
prereleas3
Boot arguments: root=/dev/ram ramdisk=0x00002000
PM interrupt vector 0 handler c00b3100
time_init: decrementer frequency = 180000000/60
Calibrating delay loop... 47.82 BogoMIPS
Memory: 11864k available (740k kernel code, 524k data, 32k init)
[c0000000,c100]
Flash addr: c4004000, CPLD addr: c4002000, UART Addr: c4000000
CPLD-20 init: r1=dc ck1=3 sc1=dc i1=ff i2=23 i3=ff i4=23 s1=0 s2=3 s3=0
s4=1
FLASH disk driver initialized: VMA c4004000 size 4096kb blocks 64
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
Initializing RT netlink socket
Starting kswapd v 1.2
Serial driver version 4.27 with SHARE_IRQ enabled
ttyS01 at 0xc4000000 (irq = 2) is a ST16C654
ttyS02 at 0xc4000008 (irq = 2) is a ST16C654
ttyS03 at 0xc4000010 (irq = 2) is a ST16C654
ttyS04 at 0xc4000018 (irq = 2) is a ST16C654
ttyS05 at 0xc4000020 (irq = 2) is a ST16C654
ttyS06 at 0xc4000028 (irq = 2) is a ST16C654
ttyS07 at 0xc4000030 (irq = 2) is a ST16C654
ttyS08 at 0xc4000038 (irq = 2) is a ST16C654
CPM UART driver version 0.03
ttyS0 on SMC1 at 0x0280, BRG1
CPM interrupt vector 4 handler c00b3560
RAM disk driver initialized: 16 RAM disks of 8192K size
eth0: FEC ENET Version 0.1, 00:fec: Phy @ 0x1, type 0x20005c20
60:2e:00:1f:fec: link down
d9
PPP: version 2.3.7 (demand dialling)
TCP compression code copyright 1989 Regents of the University of
California
PPP line discipline registered.
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
RAMDISK: Compressed image found at block 0
attempt to access beyond end of device
01:00: rw=0, want=8196, limit=8192
dev 01:00 blksize=1024 blocknr=8195 sector=16390 size=1024 count=1
EXT2-fs error (device ramdisk(1,0)): read_block_bitmap: Cannot read
block bitma0
attempt to access beyond end of device
01:00: rw=0, want=8197, limit=8192
dev 01:00 blksize=1024 blocknr=8196 sector=16392 size=1024 count=1
EXT2-fs error (device ramdisk(1,0)): read_inode_bitmap: Cannot read
inode bitma6
EXT2-fs error (device ramdisk(1,0)): ext2_check_inodes_bitmap: Wrong
free inode7
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 32k init
attempt to access beyond end of device
^[^[^[^[01:00: rw=0, want=8198, limit=8192
dev 01:00 blksize=1024 blocknr=8197 sector=16394 size=1024 count=1
EXT2-fs error (device ramdisk(1,0)): ext2_read_inode: unable to read
inode bloc7
attempt to access beyond end of device
01:00: rw=0, want=8221, limit=8192
dev 01:00 blksize=1024 blocknr=8220 sector=16440 size=1024 count=1
EXT2-fs error (device ramdisk(1,0)): ext2_read_inode: unable to read
inode bloc0
Kernel panic: No init found. Try passing init= option to kernel.
- Next message: Eli Aran: "used to windows"
- Previous message: Axel Burwitz: "Re: fedora welcome screen freezes after first install and after booting / ATI Radeon 9800 AGP8x"
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Relevant Pages
|
|
