Compaq 6400R SMP RedHat

• Previous message: Kasper Bjørn Nielsen: "Samsung Contact From 7.5 to 8.5?"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Date: 19 Oct 2004 07:11:17 -0700

Hi there,

I recently purchased a used Compaq 6400R with 4 CPUs (all working and
reporting
fine at boot time), and I installed the Red Hat Linux ES release 3.

The installation went very smoothly, and it loads the SMP kernel
(uname -r
returns 2.4.21-4.ELsmp) , however, it reports only one CPU - the
CPU#0. The
/var/log/messages reports:

Oct 18 18:59:09 rhino kernel: SMP motherboard not detected.
Oct 18 18:59:09 rhino kernel: enabled ExtINT on CPU#0

Is there anything that I can do to enable the other CPUs? I checked
on the
RedHat site, and the 6400R is definitely on their supported list...
What
gives??

The complete DMESG output follows below..

Thanks for help, Alex.

Linux version 2.4.21-4.ELsmp (bhcompile@daffy.perf.redhat.com) (gcc
version 3.2.3 20030502 (Red Hat Linux 3.2.3-20)) #1 SMP Fri Oct 3
17:52:56 EDT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fffc000 (usable)
 BIOS-e820: 000000007fffc000 - 0000000080000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 524284
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 294908 pages.
Kernel command line: ro root=LABEL=/
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 549.863 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1097.72 BogoMIPS
Memory: 2056932k/2097136k available (1683k kernel code, 35592k
reserved, 1318k data, 224k init, 1179632k highmem)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 131072 (order: 7, 524288 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Katmai) stepping 03
per-CPU timeslice cutoff: 1462.49 usecs.
task migration cache decay timeout: 10 msecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 549.8651 MHz.
..... host bus clock speed is 99.9753 MHz.
cpu: 0, clocks: 999753, slice: 499876
CPU0<T0:999744,T1:499856,D:12,S:499876,C:999753>
zapping low mappings.
Process timing init...done.
Starting migration thread for cpu 0
PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=9
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Searching for i450NX host bridges on 00:10.0
PCI: Device 00:78 not found by BIOS
PCI: Device 00:80 not found by BIOS
PCI: Device 00:90 not found by BIOS
PCI: Device 00:a0 not found by BIOS
PCI: C0 revision 450NX. Disabling PCI restreaming.
PCI: C0 revision 450NX. Disabling PCI restreaming.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 131071
aio_setup: sizeof(struct page) = 60
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
piix: 450NX errata present, disabling IDE DMA.
piix: A BIOS update may resolve this.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 00:0f.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x2c00-0x2c07, BIOS settings: hda:pio, hdb:pio
PIIX4: IDE controller at PCI slot 00:10.0
PIIX4: device not capable of full native PCI mode
PIIX4: device disabled (BIOS)
PIIX4: not 100% native mode: will probe irqs later
PIIX4: neither IDE port enabled (BIOS)
hda: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 278k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Compaq SMART2 Driver (v 2.4.26)
cpqarray: Device 0xae10 has been found at bus 1 dev 0 func 0
cpqarray: Finding drives on ida0 (Smart Array 3200)
cpqarray ida/c0d0: blksz=512 nr_blks=35561280
cpqarray ida/c0d1: blksz=512 nr_blks=35561280
blk: queue c04f7fa0, I/O limit 4095Mb (mask 0xffffffff)
Partition check:
 ida/c0d0: p1 p2 p3 p4 < p5 p6 >
 ida/c0d1: p1 p2 p3 p4 < p5 p6 >
sym53c8xx: at PCI bus 0, device 13, function 0
sym53c8xx: 53c875 detected
sym53c8xx: at PCI bus 0, device 13, function 1
sym53c8xx: 53c875 detected
sym53c875-0: rev 0x14 on pci bus 0 device 13 function 0 irq 5
sym53c875-0: ID 7, Fast-20, Parity Checking
sym53c875-1: rev 0x14 on pci bus 0 device 13 function 1 irq 10
sym53c875-1: ID 7, Fast-20, Parity Checking
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
Starting timer : 0 0
blk: queue f7faee18, I/O limit 4095Mb (mask 0xffffffff)
Starting timer : 0 0
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 224k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:08:43 Oct 3 2003
usb-uhci.c: High bandwidth mode enabled
PCI: No IRQ known for interrupt pin D of device 00:0f.2. Please try
using pci=biosirq.
usb-uhci.c: found UHCI device with no IRQ assigned. check BIOS
settings!
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,2), internal journal
Adding Swap: 1024072k swap-space (priority -1)
Adding Swap: 1024072k swap-space (priority -2)
Adding Swap: 1024056k swap-space (priority -3)
Adding Swap: 1024056k swap-space (priority -4)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,17), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ida0(72,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com>
usb-uhci.c: $Revision: 1.275 $ time 18:08:43 Oct 3 2003
usb-uhci.c: High bandwidth mode enabled
PCI: No IRQ known for interrupt pin D of device 00:0f.2. Please try
using pci=biosirq.
usb-uhci.c: found UHCI device with no IRQ assigned. check BIOS
settings!
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
inserting floppy driver for 2.4.21-4.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Intel(R) PRO/100 Network Driver - version 2.3.13-k1-1
Copyright (c) 2003 Intel Corporation

divert: allocating divert_blk for eth0
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection

divert: allocating divert_blk for eth1
e100: selftest OK.
e100: eth1: Intel(R) PRO/100 Network Connection

divert: freeing divert_blk for eth0
divert: freeing divert_blk for eth1
ip_tables: (C) 2000-2002 Netfilter core team
Intel(R) PRO/100 Network Driver - version 2.3.13-k1-1
Copyright (c) 2003 Intel Corporation

divert: allocating divert_blk for eth0
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection

divert: allocating divert_blk for eth1
e100: selftest OK.
e100: eth1: Intel(R) PRO/100 Network Connection

ip_tables: (C) 2000-2002 Netfilter core team
e100: eth0 NIC Link is Up 100 Mbps Full duplex
ip_tables: (C) 2000-2002 Netfilter core team
e100: eth1 NIC Link is Up 100 Mbps Full duplex
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
lp0: console ready
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
ide-floppy driver 0.99.newide
hda: attached ide-cdrom driver.
hda: ATAPI 24X CD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
mtrr: Intel 450NX MMC detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining

• Previous message: Kasper Bjørn Nielsen: "Samsung Contact From 7.5 to 8.5?"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]